Ti3AlC2构建梯度界面对Cu-20Sn-10Ti合金钎料钎焊金刚石磨粒磨削性能的影响

doi:10.3901/JME.2025.04.156

机械工程学报 ›› 2025, Vol. 61 ›› Issue (4): 156-166.doi: 10.3901/JME.2025.04.156

扫码分享

Ti₃AlC₂构建梯度界面对Cu-20Sn-10Ti合金钎料钎焊金刚石磨粒磨削性能的影响

崔冰¹, 江涛¹, 赵卫星¹, 傅玉灿², 杜全斌³

1. 安徽工业大学材料科学与工程学院马鞍山 243002;
2. 南京航空航天大学机电学院南京 210016;
3. 河南机电职业学院河南省超硬材料智能制造装备集成重点实验室新郑 451191

收稿日期:2024-04-05 修回日期:2024-10-16 出版日期:2025-02-20 发布日期:2025-04-14
作者简介:崔冰，女，1987年出生，硕士研究生导师。主要研究方向为新材料及异种材料连接。E-mail：bingcui6688@163.com
杜全斌(通信作者)，男，1983年出生，副教授。主要研究方向为新型钎焊材料与工艺。E-mail：paperduqb@126.com

Effect of Ti₃AlC₂ Construction Gradient Interface on Brazing Diamond Abrasive Grains with Cu-20Sn-10Ti Filler Metals

CUI Bing¹, JIANG Tao¹, ZHAO Weixing¹, FU Yucan², DU Quanbin³

1. College of Material Science and Engineering, Anhui University of Technology, Ma'anshan 243002;
2. College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016;
3. Henan Key Laboratory of Intelligent Manufacturing Equipment Integration for Superhard Materials, Henan Mechanical and Electrical Vocational College, Xinzheng 451191

Received:2024-04-05 Revised:2024-10-16 Online:2025-02-20 Published:2025-04-14

摘要/Abstract

摘要： 为了研究梯度界面对Cu基钎料钎焊金刚石试样耐磨性和界面结合强度的影响，使用不同Ti₃AlC₂含量的陶瓷颗粒对Cu基钎料进行改性，并进行金刚石磨粒的钎焊。使用电子扫描显微镜和能谱仪对钎焊试样金刚石磨粒的微观形貌和界面结构进行研究。使用高精度摩擦磨损试验仪对钎焊试样的耐磨性进行了研究。最后使用ANSYS有限元分析软件研究单界面层和梯度界面对金刚石磨粒和钎料层应力分布的影响。结果表明，Ti₃AlC₂分解生成TiC，减弱了钎焊材料中活性元素Ti与金刚石磨粒之间的剧烈反应，从而降低了金刚石磨粒的热损伤，而活性较强的Al原子与金刚石磨粒反应生成Al₄C₃界面层。Ti₃AlC₂最佳添加含量为3%时，钎焊试样的耐磨性最佳，磨削系数最低，瓷砖的去除率提高了34%。梯度界面对降低钎料层应力的效果更佳明显。

关键词: Ti₃AlC₂, 耐磨性, 梯度界面, 力学性能, 应力

Abstract: In order to investigate the effect of gradient interface on the grinding performance and interfacial bond strength of Cu-based filler metals brazed diamond specimens, Cu-based brazing materials are modified using ceramic particles with different Ti₃AlC₂ contents and diamond abrasive grits are brazed. The microstructure and interfacial structure of diamond abrasive grains of brazed specimens are evaluated using scanning electron microscope and energy dispersive spectrometer. The wear resistance of the brazed specimens is investigated using a high precision friction wear tester. Finally, the effect of single interface layer and gradient interface on the stress distribution of diamond abrasive grits and filler metals layer is studied using ANSYS finite element analysis software for research. The results indicate that Ti₃AlC₂ decomposed to form TiC, which weakened the violent reaction between the active element Ti and diamond abrasive grits in the filler metals, thus reducing the thermal damage of diamond abrasive grits, while the more active Al atoms reacted with diamond abrasive grits to form Al₄C₃ interfacial layer. The best wear resistance and lowest grinding coefficient of brazed specimens are achieved with the optimal Ti₃AlC₂ addition content of 3%, and the tile removal rate is increased by 34%. The gradient interface is more effective in reducing the stress in the brazing layer.

Key words: Ti₃AlC₂, grinding properties, gradient interface, mechanical properties, stress

中图分类号:

TG425

崔冰, 江涛, 赵卫星, 傅玉灿, 杜全斌. Ti₃AlC₂构建梯度界面对Cu-20Sn-10Ti合金钎料钎焊金刚石磨粒磨削性能的影响[J]. 机械工程学报, 2025, 61(4): 156-166.

CUI Bing, JIANG Tao, ZHAO Weixing, FU Yucan, DU Quanbin. Effect of Ti₃AlC₂ Construction Gradient Interface on Brazing Diamond Abrasive Grains with Cu-20Sn-10Ti Filler Metals[J]. Journal of Mechanical Engineering, 2025, 61(4): 156-166.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2025.04.156

http://www.cjmenet.com.cn/CN/Y2025/V61/I4/156

参考文献

[1] 聂鹏，康晓峰，王明海. 金刚石工具的性能、应用研究与进展[J]. 沈阳航空航天大学学报，2011，28(3):60-66. NIE Peng，KANG Xiaofeng，WANG Minghai. Research on property and application of diamond tools and its development[J]. Journal of Shenyang Aerospace University，2011，28(3):60-66.
[2] XU X P，TIE X R，YU Y Q. The effects of rare earth on the fracture properties of different metal-diamond composites[J]. Journal of Materials Processing Technology，2007，187(12):421-424.
[3] ZHANG L. Filler metals，brazing processing and reliability for diamond tools brazing:A review[J]. Journal of Manufacturing Processes，2021，66:651-668.
[4] CUI B，LIU Z W，ZUO R Z，et al. Microstructure and mechanical properties of vacuum brazed diamond abrasive segments with zirconium carbide reinforced Cu-based active filler metals[J]. Diamond & Related Materials，2022，126:109091.
[5] 尹孝辉，徐凡，徐东，等. 添加ZrC增强相的Cu-Sn-Ti钎料真空钎焊金刚石的微观结构和磨削性能的研究[J]. 机械工程学报，2021，57(18):182-189. YIN Xiaohui，XU Fan，XU Dong，et al. Research on microstructure and grinding performance of vacuum brazed diamond with ZrC reinforced Cu-Sn-Ti composite alloys[J]. Journal of Mechanical Engineering，2021，57(18):182-189.
[6] FAN Y G，LI K N，LI H D，et al. Profiling interfacial reaction features between diamond and Cu-Sn-Ti active filler metal brazed at 1223 K[J]. Journal of Materials Science & Technology，2022，131:100-105.
[7] KLOTZ U E，Liu C L，Khalid F A，et al. Influence of brazing parameters and alloy composition on interface morphology of brazed diamond[J]. Materials Science and Engineering A，2008，495:265-270.
[8] YAMAZAKI T，SUZUMURA A. Reaction products at brazed interface between Ag-Cu-V filler metal and diamond (111)[J]. Journal of Materials Science，2006，41:6409-6416.
[9] HUANG S F，TSAI H L，LIN S T. Effects of brazing route and brazing alloy on the interfacial structure between diamond and bonding matrix[J]. Materials Chemistry and Physics，2004，84:251-258.
[10] WANG J，Liu C，KLOTZ U K. Experimental investigation and thermodynamic assessment of the CuSnTi ternary system[J]. Calphad，2011，35(1):82-94.
[11] 俞海，刘云鹏. 梯度界面对Cu/WC_P功能梯度材料力学性能影响[J]. 机械工程学报，2021，57:182-189. YU Hai，LIU Yunpeng. The effect of gradient interface on the mechanical properties of Cu/WC_P functionally graded materials[J]. Journal of Mechanical Engineering，2021，57(6):182-189.
[12] LINDLEYL T C，UZUN H，MCSHANE H B，et al. Fatigue crack growth behavior of 2124/SiC/10p functionally graded materials[J]. Metallurgical and Materials Transactions，2010，32(7):1831-1939．
[13] HOU M，GAO J Y，YANG H B，et al. Synthesis of diamond composites via microwave sintering and the improvement of mechanical properties induced by in-situ decomposition of Ti₃AlC₂[J]. Ceramics International，2021，47:13199-13206．
[14] DUAN D Z，HAN F，DING J J，et al. Microstructure and performance of brazed diamonds with multilayer graphene-modified Cu-Sn-Ti solder alloys[J]. Ceramics International，2021，47(7):22854-22863．
[15] LIU Y，TANG X H，ZHOU S F，et al. Improving mechanical properties of Cu/Ti₃AlC₂ composites via in-situ decomposed gradient interfaces[J]. Materials Science and Engineering:A，2022，834:142615.
[16] WANG X H，ZHOU Y C. Stability and selective oxidation of aluminum in nano-laminate Ti₃AlC₂ upon heating in argon[J]. Chemistry of Materials，2003，15(19):3716-3720.
[17] Liu Z，Yang J，Zhang H，et al. Thermal stability and decomposition behavior of Cr₂TiAlC₂ at elevated temperature[J]. Ceramics International，2023，49(8):12034-12041.
[18] ZHANG J，WANG J Y，ZHOU Y C. Structure stability of Ti₃AlC₂ in Cu and microstructure evolution of Cu-Ti₃AlC₂ composites[J]. Acta Materialia，2007，55(13):4381-4390.
[19] BUHL S，Leinenbach C，Spolenak R. Failure mechanisms and cutting characteristics of brazed single diamond grains[J]. International Journal of Advanced Manufacturing Technology，2013，66:775-786.
[20] DING W，XU J H，CHEN Z Z，et al. Interface characteristics and fracture behavior of brazed polycrystalline cBN grains using CuSnTi alloy[J]. Materials Science and Engineering:A，2013，559:629-634.
[21] DUAN D Z，MA Y S，DING J J，et al. Effect of multilayer graphene addition on performance of brazed diamond drill bits with Ni-Cr alloy and its mechanism[J]. Ceramics International，2020，46(10):16684-16692.
[22] 陈康华，方玲，李侠，等. 颗粒失效对SiCp/Al复合材料强度的影响[J]. 中南大学学报，2008，39(3):493-499. CHEN Kanghua，FANG Ling，LI Xia，et al. Influence of particle failure on strength of SiCp/Al composites[J]. Journal of Central South University，2008，39(3):493-499.
[23] 柴东朗，曹利强，李晓军，等. 镁基复合材料微区力学状态的有限元分析[J]. 稀有金属材料与工程，2005，34(1):60-63. CHAI Donglang，CAO Liqiang，LI Xiaojun，et al. Finite element analysis of micro-mechanics behavior on magnesium matrix composites[J]. Rare Metal Materials and Engineering，2005，34(1):60-63.
[24] 季冬明. 磨料预钎焊金刚石工具的加工性能研究[D]. 南京:南京航空航天大学，2016. JI Dongming. Working performance evaluation of the abrasive grains pre-brazed diamond tool[D]. Nanjing:Nanjing University of Aeronautics and Astronautics，2016.
[25] 张鹏，李付国. 界面对颗粒增强金属基复合材料强化性能的影响[J]. 材料科学与工艺，2010，18(2):192-198. ZHANG Peng，LI Fuguo. Interfacial effects on the strengthening behavior of metal matrix composite reinforced with SiC particles[J]. Matetials Science & Technology，2010，18(2):192-198.
[26] 段端志. 磨料预钎焊金刚石工具的基础[D]. 南京:南京航空航天大学，2016. DUAN Duanzhi. Fundamental research on metal bonded diamond tools with pre-brazed diamond abrasive grits [D]. Nanjing:Nanjing University of Aeronautics and Astronautics，2016.

Ti₃AlC₂构建梯度界面对Cu-20Sn-10Ti合金钎料钎焊金刚石磨粒磨削性能的影响

Effect of Ti₃AlC₂ Construction Gradient Interface on Brazing Diamond Abrasive Grains with Cu-20Sn-10Ti Filler Metals

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	夏子文, 单晨伟, 张猛猛, 刘文港, 崔敏超, 罗明. 超声椭圆振动铣削GH4169切削特性及亚表层力学性能研究[J]. 机械工程学报, 2026, 62(7): 439-451.
[2]	魏兆成, 曾文, 施宁, 房玉鑫, 李加胜, 郭明龙. 超声应力测量的高重复精度控制方法及应用开发[J]. 机械工程学报, 2026, 62(6): 209-219.
[3]	师英杰, 徐科, 雷泰然, 张毅. 基于电磁超声横波双折射的钢板应力检测方法[J]. 机械工程学报, 2026, 62(6): 257-266.
[4]	郑文健, 胡铭汇, 余洋, 冯道臣, 闫德俊, 杨建国. 高镁铝合金焊接接头软化行为对焊接残余应力的影响研究[J]. 机械工程学报, 2026, 62(4): 180-189.
[5]	韩新宇, 刘峻嵩, 石岩. 激光粉末床熔融B₄Cp/Al复合材料的性能研究[J]. 机械工程学报, 2026, 62(4): 224-232.
[6]	黎凯, 蒋笑, 方学伟, 陈瑞凯, 王航, 李昌泽, 黄科, 卢秉恒. 激光冲击对电弧熔丝直接能量沉积Al-Zn-Mg薄壁构件的性能影响研究[J]. 机械工程学报, 2026, 62(3): 137-145.
[7]	王迪, 卫洋, 郑品铸, 田印仟, 杨永强, 周恒, 黎燕文, 张世钦, 韩昌骏. 层间停留时间对激光增材成形GH3536合金温度场与沉积质量的影响研究[J]. 机械工程学报, 2026, 62(3): 146-159.
[8]	刘腾飞, 杨腾锐, 田小永, 吴玲玲, 李涤尘. 面向空间极端环境的聚醚醚酮及其复合材料真空3D打印工艺机理与性能[J]. 机械工程学报, 2026, 62(3): 271-281.
[9]	潘勤学, 赵广源, 于昊申, 徐佳褀. 基于临界折射纵波的碳纤维复合材料应力检测方法的研究[J]. 机械工程学报, 2026, 62(2): 48-60.
[10]	徐宁, 孙占勇, 杨超, 任尊松, 杨广雪, 周义昌, 屈升. 动车组设备舱底板疲劳损伤特征试验研究[J]. 机械工程学报, 2026, 62(2): 250-260.
[11]	姚帅, 戴巨川, 吕伟荣. 基于频率法的风电机组混合塔筒拉索索力检测技术研究[J]. 机械工程学报, 2026, 62(2): 385-396.
[12]	罗智超, 唐倩, 宋军, 张远航, 陈俊杰, 马帅, 冯琪翔. 四方对称TPMS晶格结构的设计及各向异性分析[J]. 机械工程学报, 2026, 62(1): 347-360.
[13]	李玉梅, 陈健, 李亚冠, 陈韵之, 聂振国. 基于图神经网络的直接能量沉积工艺3D工件全局残余应力场预测[J]. 机械工程学报, 2026, 62(1): 421-435.
[14]	钦兰云, 袁溪涟, 赵朔, 杨光, 王向明. 电弧模式对Ti/Al异质合金直接增材制造界面组织与力学行为影响研究[J]. 机械工程学报, 2025, 61(9): 199-210.
[15]	蔡金虎, 荣见华, 丁慧冰, 赵磊, 张明军, 赵志军. 基于连续体拓扑优化的拉/压结构设计方法[J]. 机械工程学报, 2025, 61(9): 449-460.