近a型钛合金航空锻件宏观清晰晶形成机理及预测模型

doi:10.3901/JME.2021.08.133

摘要/Abstract

摘要： 在双相区锻造成形的某TA15钛合金模锻件表现出局部粗大的清晰晶缺陷。利用金相拼接技术及逐点统计手段对不同晶区的宏微观组织进行分析。研究发现清晰晶区域与模糊晶区域均表现为典型的双态组织。与模糊晶区域对比，清晰晶区域初生等轴α相（α_p）含量略低，次生α相片层略厚且存有大量的粗大原始β晶粒，其平均尺寸可达模糊晶区域的3倍以上。对比研究表明，粗大的原始β晶粒是导致清晰晶缺陷最主要因素，依据试验分析结果给出了锻件出现低倍清晰晶的临界条件。采用模锻件同批次原材料通过热压缩试验，获得了该材料在不同变形条件下宏微观组织的变化规律，进而建立TA15钛合金原始β晶粒尺寸的预测模型，实现了低倍粗晶的可视化预测。研究表明动态相变是造成β晶粒粗化的最主要原因，是导致低倍组织出现清晰晶的根本原因。清晰晶对温度、变形量及应变速率均敏感，当其他条件一定时，变形温度越高、变形量越大及应变速率越小，出现清晰晶的倾向均比较越大。

关键词: 钛合金, 低倍组织, 清晰晶, 预测模型, 动态相变

Abstract: The local coarse and clear grain defects are found in the TA15 titanium alloy die forging formed in the dual phase region. The metallographic stitching technology and point by point statistical method are used to analyze the macrostructure and microstructure of different macro-grain regions. It is found that the microstructure of clear grain region and fuzzy grain region are typical duplex microstructure of the titanium alloy. Compared with the fuzzy grain region, the content of primary equiaxes α phase (α_P) in clear grain region is slightly lower, and the lamellar thickness of secondary α phase is slightly thicker, but there are a lot of coarse original β grains, whose average size is more than 3 times of that of fuzzy-grained region. According to papers, the coarse original β grains are the main factors leading to clear grain defects. The critical condition of clear grain on the surface of the forging is proposed. The same batch of original material is used to perform hot compression tests. The evolvement law variation of macrostructure and microstructure are obtained under different deformation processes. The prediction model of the original β grain size of TA15 titanium alloy is established, so the visualization prediction of macrostructure is realized. The results show that the dynamic transformation can lead to the coarsening of β grain and the clear grain of macrostructure. The clear grain is sensitive to temperature, deformation and strain rate. When other conditions are constant, the higher the deformation temperature, the larger the deformation amount and the smaller the strain rate, the higher the tendency of macrostructure to be clear grain.

Key words: titanium alloy, macrostructure, clear grain, prediction model, dynamic transformation

中图分类号:

TG319

张启飞, 金淼, 陈雷, 张禹森, 杨帅, 郭宝峰. 近a型钛合金航空锻件宏观清晰晶形成机理及预测模型[J]. 机械工程学报, 2021, 57(8): 133-145.

ZHANG Qifei, JIN Miao, CHEN Lei, ZHANG Yusen, YANG Shuai, GUO Baofeng. Formation Mechanism and Prediction Model of Macro Clear Grains in Near α Titanium Alloy Aviation Forgings[J]. Journal of Mechanical Engineering, 2021, 57(8): 133-145.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2021.08.133

http://www.cjmenet.com.cn/CN/Y2021/V57/I8/133

参考文献

[1] 李献民，刘立，董洁，等. 钛及钛合金材料应用经济性分析[C/CD]//中国有色金属工业协会钛锆铪分会. 2015. LI Xianmin，LIU Li，DONG Jie，et al. Economic analysis and decreasing cost process of titanium and titanium alloy[C/CD]//Titanium，Zirconium and Hafnium Branch of China Nonferrous Metals Industry Association，2015.
[2] 何耿煌，吴明阳，李凌祥，等. 典型钛合金切削层相变形成机理及其影响因素研究[J]. 机械工程学报，2018，54(17)：133-141. HE Genghuang，WU Mingyang，LI Lingxiang，et al. Study on the formation mechanism of phase transformation and the influencing factors of cutting layer of the typical titanium alloy[J]. Journal of Mechanical Engineering，2018，54(17)：133-141.
[3] 贺建超，张田仓，何胜春. Ti600/TC17钛合金惯性摩擦焊接头组织与力学性能研究[J]. 机械工程学报，2017，53(22)：95-100. HE Jianchao，ZHANG Tiancang，HE Shengchun. Research of microstructure and mechanical properties of Ti600/TC17 inertia friction welding joints[J]. Journal of Mechanical Engineering，2017，53(22)：95-100.
[4] 赵永庆，辛社伟，陈永楠，等. 中国战略性新兴产业-新材料·新型合金材料—钛合金[M]. 北京：中国铁道出版社，2017. ZHAO Yongqing，XIN Shewei，CHEN Yongnan，et al. China's strategic emerging industries-new materials，new alloy materials - titanium alloys[M]. Beijing：China Railway Publishing House，2017.
[5] 中国锻压协会. 特种合金及其锻造[M]. 北京：国防工业出版社，2009.Confederation of Chinese Metalforming Industry. Special alloys and their forging[M]. Beijing：National Defense Industry Press，2009.
[6] 李敏娜，卢凯凯，周立鹏，等. 加热温度及变形量对TC4钛合金棒材低倍清晰晶现象的影响[J]. 金属热处理，2019，44(12)：128-132. LI Minna，LU Kaikai，ZHOU Lipeng，et al. Effects of heating temperature and deformation on microstructure of clear crystal in TC4 titanium alloy bar[J]. Heat Treatment of Metals，2019，44(12)：128-132.
[7] 姚泽坤，郭鸿镇，邹永恒，等. 改善大尺寸钛合金自由锻件组织均匀性的方法[J]. 锻压技术，2005(5)：4-6. YAO Zekun，GUO Hongzhen，ZOU Yongheng，et al. Method of improving structure uniformity of big size titanium open-die forgings[J]. Forging and Stamping Technology，2005(5)：4-6.
[8] GAO X，ZENG W，MA H，et al. The origin of coarse macrograin during thermo-mechanical processing in a high temperature titanium alloy[J]. Journal of Alloys and Compounds，2018，775：589-600.
[9] 孙杰，柯映林. 残余应力对航空整体结构件加工变形的影响分析[J]. 机械工程学报，2005，41(2)：117-122. SUN Jie，KE Yinglin. Study on machining distortion of unitization airframe due to residual stress[J]. Journal of Mechanical Engineering，2005，41(2)：117-122.
[10] 陈飞，刘建生，马越. 关于轴类锻件拔长过程中组织均匀性控制的研究[J]. 机械工程学报，2018，54(10)：127-133. CHEN Fei，LIU Jiansheng，MA Yue. Research on controlling organization uniformity of axial forgings in the process of swaging[J]. Journal of Mechanical Engineering，2018，54(10)：127-133.
[11] 马济民，贺金宇，庞克昌. 钛铸锭和锻造[M]. 北京：冶金工业出版社，2012. MA Jimin，HE Jinyu，PANG Kechang. Titanium ingot and forging[M]. Beijing：Metallurgical Industry Press，2012.
[12] 周义刚，曾卫东，俞汉清. 钛合金高温形变强韧化研究[J]. 机械工程学报，1996，32(5)：70-73. ZHOU Yigang，ZENG Weidong，YU Hanqing. Investigation on the high temperature deformation strength-toughening of titanium alloy[J]. Journal of Mechanical Engineering，1996，32(5)：70-73.
[13] 姚泽坤，郭鸿镇，苏祖武. 改善钛合金棒材和锻件低倍和高倍组织的研究[J]. 西北工业大学学报，1992(4)：487-494. YAO Zekun，GUO Hongzhen，SU Zuwu. Study on improving macrostructure and macrostructure of titanium alloy bars and forgings[J]. Journal of Northwest Polytechnical University，1992(4)：487-494.
[14] 王华. TC4-DT钛合金模锻件组织和性能的控制研究[J]. 热加工工艺，2017(13)：171-173. WANG Hua. Control study on microstructure and properties of TC4-DT titanium alloy die forgings[J]. Hot Working Technology，2017(13)：171-173.
[15] JONAS J J，JR C A，FALL A，et al. Transformation softening in three titanium alloys[J]. Materials &; Design，2017，113：305-310.
[16] FOUL A，ARANAS C，GUO B，et al. Dynamic transformation of α → β titanium at temperatures below the β-transus in commercially pure titanium[J]. Materials Science and Engineering A，2018，722(11)：156-159.
[17] KOIKE J，SHIMOYAMA Y，OHNUMA I，et al. Stress-induced phase transformation during superplastic deformation in two-phase Ti-Al-Fe alloy[J]. Acta Materialia，2000，48(9)：2059-2069.
[18] GUO B，SEMIATIN S L，JONAS J J，et al. Dynamic transformation of Ti-6Al-4V during torsion in the two-phase region[J]. Journal of Materials Science，2018，53(12)：1-11.
[19] ABBASI S M，MOMENI A. Effect of hot working and post-deformation heat treatment on microstructure and tensile properties of Ti-6Al-4V alloy[J]. Transactions of Nonferrous Metals Society of China，2011，21(8)： 1728-1734.
[20] SADEGHPOUR S，JAVAHERI V，ABBASI S M，et al. The effect of phase stability on the grain growth behavior of beta titanium alloys[J]. Physica B Condensed Matter，2020，593：412315.
[21] 石卫民，魏寿庸，王鼎春，等. Ti60钛合金大棒材的显微组织及力学性能[J]. 中国有色金属学报，2010，20(增刊1)：75-78. SHI Weimin，WEI Shouyong，WANG Dingchun，et al. Microstructures and mechanical properties of Ti60 Ti alloy large-section bars[J]. The Chinese Journal of Nonferrous Metals，2010，20(Suppl.1)：75-78.
[22] 张津，刘贞阳，郭海明. Ti8LC钛合金热处理工艺对硬度和组织的影响[J]. 稀有金属，2011，35(1)：17-21. ZHANG Jin，LIU Zhenyang，GUO Haiming. Effect of heat treatment on hardness and microstructure of Ti8 LC alloy[J]. Chinese Journal of Rare Metals，2011，35(1)：17-21.
[23] WANG X，LI W，MA T，et al. Microstructural heredity and its effect on mechanical properties of linear friction welded Ti-6.5Al-3.5Mo-1.5Zr-0.3Si alloy joints[J]. Materials Characterization，2020，168：110540.
[24] 杨晓雅，何岸，谢甘霖，等. 核电用奥氏体不锈钢的动态再结晶行为[J]. 工程科学学报，2015，37(11)：1447-1455. YANG Xiaoya，HE An，XIE Ganlin，et al. Dynamic recrystallization behavior of an austenitic stainless steel for nuclear power plants[J]. Chinese Journal of Engineering，2015，37(11)：1447-1455.
[25] LEHNERT W，CUONG N D. Integrated model for calculating microstructural and forming parameters of steel during rolling in continuous mills[J]. Transactions of the Iron and Steel Institute of Japan，2007，35(9)：1100-1108.
[26] 肖凯，陈拂晓. 铸态铅黄铜动态再结晶模型的建立[J]. 塑性工程学报，2008，15(3)：132-137. XIAO Kai，CHEN Fuxiao. Modeling the dynamic-recrystallization of casting lead brass[J]. Journal of Plasticity Engineering，2008，15(3)：132-137.
[27] 许赵华，李宏，李淼泉. GH696合金动态再结晶模型[J]. 中国有色金属学报，2017，27(8)：1551-1562. XU Zhaohua，LI Hong，LI Miaoquan. Dynamic recrystallization model of GH696 superalloy[J]. Chinese Journal of Nonferrous Metals，2017，27(8)：1551-1562.