Al-Cu合金超低温变形行为及强化机制分析

doi:10.3901/JME.2025.14.045

摘要/Abstract

摘要： 制备Al-Cu二元合金作为模型材料，研究温度对其变形行为及强化机制的影响。通过单向拉伸测试、应变原位测量、电子显微镜观察等宏微观表征手段对比研究Al-Cu合金在不同温度下的力学性能、应变速率敏感性、塑性失稳现象 (Portevin-Le Chatelier，PLC)效应、位错演变及断口形貌，并通过相关经典理论建立起与温度相关联的强化模型。结果显示，Al-Cu合金的力学性能随温度降低先减弱后增强，越过123 K后可实现强度和伸长率的协同提升。同时，其变形转移模式随温度降低发生显著改变，由PLC带的循环传播转变为整体协调均匀变形。通过强化模型分析发现超低温对Al-Cu合金变形行为的影响主要归结于两类强化机制的竞争关系。随温度降低动态应变时效(Dynamic strain ageing，DSA)强化机制的削弱与其他强化机制的增强此消彼长，共同导致Al-Cu合金力学性能的先减弱后增强，为铝合金超低温成形技术的工艺实践提供理论基础。

关键词: 铝铜合金, 超低温, Portevin-Le Chatelier效应, 变形行为, 强化机制

Abstract: Al-Cu binary alloy is prepared as the model material, and the influence of temperature on its deformation behaviors and strengthening mechanism is studied. The mechanical properties, strain rate sensitivity, Portevin-Le Chatelier effect, dislocation evolution and fracture morphology of Al-Cu alloy at different temperatures are comprehensively studied by means of uniaxial tensile tests, in-situ strain measurement and electron microscopy observation. The temperature dependent strengthening model is established based on the classical theory. The results show that the mechanical properties of Al-Cu alloy first weaken and then increase with decreasing temperature, and the strength and elongation of Al-Cu alloy can be enhanced simultaneously when the temperature is lower than 123 K. In addition, the deformation transfer mode changes significantly with the decrease of temperature, from the cyclic propagation of PLC band to the whole coordinated uniform deformation. Through strengthening model analysis, it is found that the influence of cryogenic temperature on the deformation behavior of Al-Cu alloy is mainly attributed to the competitive relationship between two kinds of strengthening mechanisms. The weakening of dynamic strain ageing and the strengthening of other mechanisms with decreasing temperature synergistically lead to the first weakening and then strengthening of mechanical properties of Al-Cu alloy. It provides a theoretical basis for the practical application of cryogenic forming technology in aluminum alloys.

Key words: Al-Cu alloy, cryogenic temperature, Portevin-Le Chatelier effect, deformation behavior, strengthening mechanism

中图分类号:

TG111

王睿乾, 李鲁博, 刘伟. Al-Cu合金超低温变形行为及强化机制分析[J]. 机械工程学报, 2025, 61(14): 45-55.

WANG Ruiqian, LI Lubo, LIU Wei. Analysis of Deformation Behavior and Strengthening Mechanism of Al-Cu Alloy at Cryogenic Temperature[J]. Journal of Mechanical Engineering, 2025, 61(14): 45-55.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2025.14.045

http://www.cjmenet.com.cn/CN/Y2025/V61/I14/45

参考文献

[1] YUAN Shijian. Developments and perspectives on the precision forming processes for ultra-large size integrated components[J]. International Journal of Extreme Manufacturing，2019，1(2):38-55.
[2] YUAN Shijian. Fundamentals and processes of fluid pressure forming technology for complex thin-walled components[J]. Engineering，2021，7(3):358-366.
[3] ZHENG Kailun，POLITIS D J，WANG Liliang，et al. A review on forming techniques for manufacturing lightweight complex-shaped aluminium panel components[J]. International Journal of Lightweight Materials and Manufacture，2018，1(2):55-80.
[4] LIU Jun，WANG Ailing，GAO Haoxiang，et al. Transition of failure mode in hot stamping of AA6082 tailor welded blanks[J]. Journal of Materials Processing Technology，2018，257:33-44.
[5] YUAN Shijian，CHENG Wangjun，LIU Wei，et al. A novel deep drawing process for aluminum alloy sheets at cryogenic temperatures[J]. Journal of Materials Processing Technology，2020，284:116743.
[6] YUAN Shijian. Frozen forming method for large tailored plate aluminum alloy component:USA，10376943B1[P]. 2019-08-15.
[7] FAN Xiaobo，CHEN Xianshuo，YUAN Shijian. Novel forming process for aluminum alloy thin shells at ultra-low temperature gradient[J]. International Journal of Machine Tools and Manufacture，2023，185:103992.
[8] WANG Chenguang，YI Youping，WANG Haihang，et al. Investigation on the formability and deformation mechanism of aluminum alloy thin-walled parts at cryogenic temperature[J]. Journal of Materials Processing Technology，2023，319:118041.
[9] DONG Fei，HUANG Shiquan，YI Youping，et al. Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature[J]. Journal of Alloys and Compounds，2023，968:171992.
[10] FENG Bin，GU Bin，LI Shuhui. Cryogenic deformation behavior and failure mechanism of AA7075 alloy sheets tempered at different conditions[J]. Materials Science and Engineering:A，2022，848:143396.
[11] FU Yunfan，CHEN Canyang，LIU Xuefeng，et al. Research on the ultra-low temperature tensile deformation mechanism of Al-Mg-Si alloys in different heat treatment states[J]. Journal of Alloys and Compounds，2025，1010:177150.
[12] WANG Ruiqian，LIU Wei，YAO Mengjia. Cooperative effect of grain size and cryogenic temperature on deformation behavior and mechanism of commercial pure Al sheets[J]. Materials Science and Engineering:A，2024，899:146411.
[13] 程旺军. 2219铝合金薄板超低温变形行为与成形性能[D]. 哈尔滨:哈尔滨工业大学，2021. CHENG Wangjun. Deformation behavior and formability of 2219 aluminum alloy sheets at cryogenic temperature[D]. Harbin:Harbin Institute of Technology，2021.
[14] PENG Youhong，LIU Chenglu，GENG Lin，et al. Microstructures and cryogenic mechanical properties of spray deposited 2195 Al-Cu-Li alloy with different heat treatments[J]. Materials Science and Engineering:A，2024，895:146173.
[15] 董非. 铝锂合金薄板超低温变形行为与拉深成形工艺研究[D]. 长沙:中南大学，2022. DONG Fei. Research on cryogenic deformation behaviors and deep drawing technique of Al-Li alloy sheet [D]. Changsha:Central South University，2022.
[16] KREYCA J，KOZESCHNIK E. State parameter-based constitutive modelling of stress strain curves in Al-Mg solid solutions[J]. International Journal of Plasticity，2018，103:67-80.
[17] XU Jianbin. HOLMEDAL B，HOPPERSTAD O S，et al. Dynamic strain ageing in an AlMg alloy at different strain rates and temperatures:Experiments and constitutive modelling[J]. International Journal of Plasticity，2022，151:103215.
[18] ZHOU Dengshan，ZHANG Xiuzhang，TEHRANCHI A，et al. Stacking faults in a mechanically strong Al(Mg)-Al₃Mg₂ composite[J]. Composites Part B，2022，245:110211.
[19] AN Xianghai，WU Shiding，WANG Zhongguang，et al. Significance of stacking fault energy in bulk nanostructured materials:Insights from Cu and its binary alloys as model systems[J]. Progress in Materials Science，2019，101:1-45.
[20] SCHULTHESS T C，TURCHI P E A，GONIS A，et al. Systematic study of stacking fault energies of random Al-based alloys[J]. Acta Materialia，1998，46(6):2215-2221.
[21] CHEN Yu，WEYLAND M，HUTCHINSON C R. The effect of interrupted aging on the yield strength and uniform elongation of precipitation-hardened Al alloys[J]. Acta Materialia，2013，61(15):5877-5894.
[22] VIERNSTEIN B，SOLYOM L，KOZESCHNIK E. Strain hardening in dilute binary Al-Cu，Al-Zn，and Al-Mn alloys:Experiment and modeling[J]. Metallurgical and Materials Transactions A，2024，55:3627-3639.
[23] ZOLOTOREVSKY N Y，SOLONIN A N，CHURYUMOV A Y，et al. Study of work hardening of quenched and naturally aged Al-Mg and Al-Cu alloys[J]. Materials Science and Engineering:A，2009，502(1-2):111-117.
[24] CHEN Han，CHEN Yanchi，TANG Yifei，et al. Quantitative assessment of the influence of the Portevin-Le Chatelier effect on the flow stress in precipitation hardening AlMgScZr alloys[J]. Acta Materialia，2023，255(15):119060.
[25] KABIRIAN F，KHAN A S，PANDEY A. Negative to positive strain rate sensitivity in 5xxx series aluminum alloys:Experiment and constitutive modeling[J]. International Journal of Plasticity，2014，55:232-246.
[26] ROWLANDS B S，RAE C，GALINDO-NAVA E. The Portevin-Le Chatelier effect in nickel-base superalloys:Origins，consequences and comparison to strain ageing in other alloy systems[J]. Progress in Materials Science，2023，132:101038.
[27] XU Jie，LI Jianwei，SHI Lei，et al. Effects of temperature，strain rate and specimen size on the deformation behaviors at micro/meso-scale in ultrafine-grained pure Al[J]. Materials Characterization，2015，109:181-188.
[28] ZHAO Shiteng，MENG Chenlu，MAO Fengxin，et al. Influence of severe plastic deformation on dynamic strain aging of ultrafine grained Al-Mg alloys[J]. Acta Materialia，2014，76:54-67.
[29] REN S C，MORGENEYER T F，MAZIÈRE M，et al. Effect of Lüders and Portevin-Le Chatelier localization bands on plasticity and fracture of notched steel specimens studied by DIC and FE simulations[J]. International Journal of Plasticity，2021，136:102880.
[30] DONG Fei，HUANG Shiquan，YI Youping，et al. Flow behaviors and deformation mechanism of WQ-tempered Al-Li alloy at cryogenic temperatures[J]. Materials Science and Engineering:A，2021，809:140971.
[31] PENG Youhong，WANG Li，LIU Chenglu，et al. Revealing the exceptional cryogenic strength-ductility synergy of a solid solution 6063 alloy by in-situ EBSD experiments[J]. Journal of Materials Science & Technology，2025，208(10):313-322.
[32] SUN Shijie，TIAN Yanzhong，LIN Hairong，et al. Temperature dependence of the Hall-Petch relationship in CoCrFeMnNi high-entropy alloy[J]. Journal of Alloys and Compounds，2019，806:992-998.
[33] CORDERO Z C，KNIGHT B E，SCHUH C A. Six decades of the Hall-Petch effect - a survey of grain-size strengthening studies on pure metals[J]. International Materials Reviews，2016，61(8):495-512.
[34] YAO Kai，XIN Shewei，YANG Yi，et al. Ultrahigh cryogenic strength and exceptional ductility at 20 K in a TWIP Ti-15Mo alloy[J]. Scripta Materialia，2022，213:114595.
[35] LEYSON G P M，JR L G H，CURTIN W A. Solute strengthening from first principles and application to aluminum alloys[J]. Acta Materialia，2012，60(9):3873-3884.
[36] CURTIN W A，OLMSTED D L，JR L G H. A predictive mechanism for dynamic strain ageing in aluminium- magnesium alloys[J]. Nature Materials，2006，5:875-880.
[37] SAMANTA S，SAHOO J R，MISHRA S. A robust phenomenological modeling framework based on cross-slip propensity factor for capturing the effect of dynamic strain aging on work hardening behavior of an Al-Mg alloy[J]. Acta Materialia，2023，254:119014.
[38] KERALAVARMA S M，BOWER A F，CURTIN W A. Quantum-to-continuum prediction of ductility loss in aluminium-magnesium alloys due to dynamic strain aging[J]. Nature Communications，2014，5:4604.
[39] CALCAGNOTTO M，PONGE D，DEMIR E，et al. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD[J]. Materials Science and Engineering:A，2010，527(10-11):2738-2746.
[40] SAMANTA S，SAHOO J R，MISHRA S. Effect of dynamic strain ageing on flow stress and critical strain for jerky flow in Al-Mg alloys[J]. International Journal of Plasticity，2024，180:104053.
[41] LIU Wei，WANG Ruiqian，ZHOU Huabo，et al. Modeling of cryo-deformation based on grain size-dependent dislocation evolution[J]. International Journal of Mechanical Sciences，2025，285(1):109813.
[42] CHENG Wangjun，LIU Wei，FAN Xiaobo，et al. Cooperative enhancements in ductility and strain hardening of a solution-treated Al-Cu-Mn alloy at cryogenic temperatures[J]. Materials Science and Engineering:A，2020，790:139707.
[43] SHI Rongjian，WANG Zidong，QIAO Lijie，et al. Microstructure evolution of in-situ nanoparticles and its comprehensive effect on high strength steel[J]. Journal of Materials Science & Technology，2019，35(9):1940-1950.
[44] FIGUEIREDO R B，LANGDON T G. Effect of grain size on strength and strain rate sensitivity in metals[J]. Journal of Materials Science，2022，57(8):5210-5229.
[45] ZHANG Xiuzhen，YANG Chao，MENG Lei，et al. The influence of precipitation on plastic deformation in a high Mg-containing AlMgZn-based crossover alloy:Slip localization and strain hardening[J]. International Journal of Plasticity，2024，173:103896.
[46] LEYSON G P M，CURTIN W A. Solute strengthening at high temperatures[J]. Modelling and Simulation in Materials Science and Engineering，2016，24(6):065005.
[47] LEYSON G P M，CURTIN W A，JR L G H，et al. Quantitative prediction of solute strengthening in aluminium alloys[J]. Nature Materials，2010，9:750-755.
[48] CAI Mingchun，NIU Lisha，YU Tao，et al. Strain rate and temperature effects on the critical strain for Portevin-Le Chatelier effect[J]. Materials Science and Engineering:A，2010，527(20):5175-5180.
[49] TIAN Teng，ZHA Min，JIA Hailong，et al. The effect of high solid solution Mg contents (7-13 wt%) on the dynamic strain aging behavior of Al-Mg alloys[J]. Materials Science，2023，880(26):145376.
[50] JIANG Lei，FU Huadong，ZHANG Hongtao，et al. Physical mechanism interpretation of polycrystalline metals’ yield strength via a data-driven method:A novel Hall-Petch relationship[J]. Acta Materialia，2022，231:117868.