• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (17): 473-481.doi: 10.3901/JME.260577

• 制造工艺与装备 • 上一篇    

扫码分享

超声辅助电火花线切割加工形状记忆合金枝晶细化生长机理研究

王艳, 李天成, 陈宇, 王传琦, 杜林, 马豪杰   

  1. 上海理工大学机械工程学院 上海 200093
  • 收稿日期:2025-09-16 修回日期:2025-12-24 发布日期:2026-11-20
  • 作者简介:王艳(通信作者),女,1969年出生,博士,教授,博士研究生导师。主要研究方向为精密加工、磨削加工技术和特种加工技术。E-mail:yanwang909909@163.com
  • 基金资助:
    国家自然科学基金资助项目(52675595)。

Ultrasonic-assisted Electric Discharge Wire-cutting Processing of Shape Memory Alloy Dendrite Refinement Growth Mechanism Study

WANG Yan, LI Tiancheng, CHEN Yu, WANG Chuanqi, DU Lin, MA Haojie   

  1. School of Mechanical Engineering, University of Shanghai for Science and Technology, Shanghai 200093
  • Received:2025-09-16 Revised:2025-12-24 Published:2026-11-20

摘要: 传统慢走丝电火花线切割加工(Conventional slow-feed wire EDM,WEDM-LS)在加工Ni-Ti形状记忆合金时,常面临加工效率低、表面质量差等问题。工件的力学性能主要由加工过程中形成的微观组织决定,因此,通过精确控制微观组织的演变,可以有效调控合金的力学性能。为解决这一问题,将超声振动引入WEDM-LS工艺中,研究了超声振动对熔池中枝晶生长过程的影响。通过Matlab建立的数值模型,利用耦合相场法分别模拟了自然对流和超声耦合作用下单枝晶生长过程,并对比了多个枝晶在施加超声前后的形态和生长行为。模拟结果表明,超声振动通过影响熔体流场和溶质迁移,显著改变了枝晶的生长形态。对比试验表明,相较于传统电火花线切割,超声振动辅助电火花线切割显著细化了工件微观组织:最大表面高度差降低22.3%,总固相分数提升32.53%,平均晶粒尺寸减小31.98%。揭示了超声振动通过影响枝晶稳态生长速度、形态演化及合金凝固过程,有效细化枝晶结构、改善微观组织。

关键词: 电火花线切割加工, 微观组织, 相场法, 枝晶生长, 格子玻尔兹曼方法

Abstract: Conventional slow-feed wire EDM (WEDM-LS) often faces problems such as low processing efficiency and poor surface quality when machining NiTi shape memory alloys. The mechanical properties of the workpiece are mainly determined by the microstructure formed during the machining process, therefore, the mechanical properties of the alloy can be effectively regulated by precisely controlling the evolution of the microstructure. To solve this problem, this study introduces ultrasonic vibration into the WEDM-LS process, and combines the lattice Boltzmann method (LBM) with the phase field (PF) method to investigate the effect of ultrasonic vibration on the growth process of dendrites in the melt pool. In this paper, through the numerical model established by Matlab, firstly, the lattice Boltzmann method with coupled phase field is used to simulate the growth process of single dendrite under natural convection and ultrasonic coupling, respectively, and on this basis, the morphology and growth behavior of multiple dendrites before and after the application of ultrasound are compared. The simulation results show that ultrasonic vibration significantly changes the growth morphology of dendrites by affecting the melt flow field and solute migration. Finally, the comparison tests between conventional EDM and ultrasonic vibration-assisted EDM were carried out respectively. The results show that the microstructure of the workpieces under the condition of ultrasonic vibration-assisted EDM is obviously refined, which is in line with the simulation results, and the average grain size has been reduced by 31.98% after the EBSD test, which reveals the influence mechanism of the ultrasonic vibration on the steady state growth rate of the dendritic crystals, the morphology evolution, and the solidification process, indicating that ultrasonic vibration can effectively change the growth morphology and growth behavior of dendrites before and after the application of ultrasound. It reveals the influence mechanism of ultrasonic vibration on the steady state growth rate of dendrites, morphological evolution and solidification process of the alloy, indicating that ultrasonic vibration can effectively refine the structure of dendrites and improve the microstructure of alloy.

Key words: WEDM, microstructure, phase field method, dendrite growth, lattice Boltzmann method

中图分类号: