高扭矩密度仿人机器人驱动单元研究

doi:10.3901/JME.2022.18.192

机械工程学报 ›› 2022, Vol. 58 ›› Issue (18): 192-204.doi: 10.3901/JME.2022.18.192

扫码分享

高扭矩密度仿人机器人驱动单元研究

李慧莱^1,2, 凌振飞^1,2, 王泽正^1,2, 孙茂文^1,2, 刘浩^1,3, 欧阳小平^1,2, 李斌斌⁴

1. 浙江大学机械工程学院杭州 310027;
2. 浙江大学流体动力与机电系统国家重点实验室杭州 310027;
3. 浙江大学先进技术研究院杭州 310027;
4. 乾元科学研究院杭州 310008

收稿日期:2022-03-01 修回日期:2022-07-10 出版日期:2022-09-20 发布日期:2022-12-08
通讯作者: 欧阳小平(通信作者)，男，1974年出生，博士，教授，博士研究生导师。主要研究方向为飞机液压、外骨骼机器人、仿人机器人。E-mail：ouyangxp@zju.edu.cn
作者简介:李慧莱,男,1998年出生,博士研究生。主要研究方向为仿人机器人;E-mail:12025010@zju.edu.cn
基金资助:
国家重点研发计划(2018YFB1305402)、国家自然科学基金(51890883)、流体动力与机电系统国家重点实验室自主课题(SKLoFP_ZZ_2016)和1912资助项目。

Research on High Torque Density Drive Unit for Humanoid Robots

LI Huilai^1,2, LING Zhenfei^1,2, WANG Zezheng^1,2, SUN Maowen^1,2, LIU Hao^1,3, OUYANG Xiaoping^1,2, LI Binbin⁴

1. School of Mechanical Engineering, Zhejiang University, Hangzhou 310027;
2. State Key Laboratory of Fluid Power and Mechatronic Systems, Zhejiang University, Hangzhou 310027;
3. Institute of Advanced Technology, Zhejiang University, Hangzhou 310027;
4. Institute of Science, Qianyuan, Hangzhou 310008

Received:2022-03-01 Revised:2022-07-10 Online:2022-09-20 Published:2022-12-08

摘要/Abstract

摘要： 驱动单元是协作型仿人机器人的核心部件之一。研制出一种用于大负载仿人机械臂的小体积、高扭矩密度、高动态性能和抗倾覆的驱动单元。通过合理的槽极匹配结合径向长度和轴向厚度等电机机械结构参数的优化，设计出一种高径长比外转子永磁同步电机。通过分析驱动单元减速器部件的受力形式设计了抗倾覆两级行星减速器。建立驱动单元的动力学模型，对驱动单元样机进行集成研制。基于实际试验台对驱动单元样机进行系统辨识和负载特性测试，验证了所研制的驱动单元满足仿人机械臂的应用需求。汇演结果表明，所设计的驱动单元具有体积小、扭矩密度高和动态性能好等优点，外形尺寸降至88.5 mm×35 mm，额定扭矩密度高达35.97 N«m/kg，空载工况下闭环控制带宽达到47.6 Hz。

关键词: 驱动单元, 仿人机器人, 扭矩密度, 抗倾覆, 电机, 减速器

Abstract: The drive unit is one of the core components of collaborative humanoid robots. A small volume, high torque density, high dynamic performance, and anti-overturning drive unit is developed for the large-load humanoid robotic arm. A high diameter-length ratio outer rotor permanent magnet synchronous motor is designed through good slot-pole matching and optimization of mechanical parameters such as radial length and axial thickness. An anti-overturning two-stage planetary reducer is designed by analyzing the forces acting on the drive unit components. The dynamic model of the drive unit is established, and the drive unit prototype is integrated and developed. Based on the actual test bench, the system identification and load characteristic test of the drive unit prototype are carried out, and it is verified that the designed drive unit meets the application requirements of the humanoid robotic arm. The experimental results show that the designed drive unit has the advantages of small size, high torque density, and good dynamic performance. The overall size is reduced to 88.5 mm × 35 mm, the torque density is as high as 35.97 N«m/kg under the rated load condition, and the closed-loop control bandwidth under the no-load condition is up to 47.6 Hz.

Key words: drive unit, humanoid robot, torque density, anti-overturning, motor, reducer

中图分类号:

TG156

李慧莱, 凌振飞, 王泽正, 孙茂文, 刘浩, 欧阳小平, 李斌斌. 高扭矩密度仿人机器人驱动单元研究[J]. 机械工程学报, 2022, 58(18): 192-204.

LI Huilai, LING Zhenfei, WANG Zezheng, SUN Maowen, LIU Hao, OUYANG Xiaoping, LI Binbin. Research on High Torque Density Drive Unit for Humanoid Robots[J]. Journal of Mechanical Engineering, 2022, 58(18): 192-204.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2022.18.192

http://www.cjmenet.com.cn/CN/Y2022/V58/I18/192

参考文献

[1] 黄思翰，王柏村，张美迪，等. 面向人本智造的新一代操作工:参考架构、使能技术与典型场景[J/OL]. 机械工程学报，[2022-08-06]. http://kns.cnki.net/kcms/detail/11.2187.TH.20220727.1117.054.html. HUANG Sihan，WANG Baicun，ZHANG Meidi，et al. Towards human-centric smart manufacturing: Framework, enabling technologies and typical scenarios of Operator 4.0[J/OL]. Journal of Mechanical Engineering. [2022-08-06]. http://kns.cnki.net/kcms/detail/11.2187.TH.20220727.1117.054.html.
[2] MICHALOS G，KOUSI N，KARAGIANNIS P，et al. Seamless human robot collaborative assembly-an automotive case study[J]. Mechatronics，2018，55:194-211.
[3] FAGER P，CALZAVARA M，SGARBOSSA F. Modeling time efficiency of cobot-supported kit preparation[J]. The International Journal of Advanced Manufacturing Technology，2020，106:2227-2241.
[4] Lohmeier S，Buschmann T，Ulbrich H，et al. Modular joint design for performance enhanced humanoid robot LOLA[C]//Proceedings 2006 IEEE International Conference on Robotics and Automation. Orlando:International Conference on Robotics and Automation ，2006:88-93.
[5] Procter S，Secco E L. Design of a biomimetic BLDC driven robotic arm for teleoperation & biomedical applications[J]. Journal of Human, Earth，and Future，2021，2(4):345-354.
[6] Baccelliere L，Kashiri N，Muratore L，et al. Development of a human size and strength compliant bi-manual platform for realistic heavy manipulation tasks[C]//2017 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS). Vancouver:International Conference on Intelligent Robots and Systems (IROS)，2017:5594-5601.
[7] Katz B G. A low cost modular actuator for dynamic robots[D]. Massachusetts:Massachusetts Institute of Technology，2018.
[8] KAMINAGA H，KO T，MASUMURA R，et al. Mechanism and control of whole-body electro-hydrostatic actuator driven humanoid robot hydra[C]//2016 International Symposium on Experimental Robotics. Cham:International Symposium on Experimental Robotics，2016:656-665.
[9] SUN Maowen，OUYANG Xiaoping，MATTILA J，et al. One novel hydraulic actuating system for the lower-body exoskeleton[J]. Chinese Journal of Mechanical Engineering，2021，34(1):1-10.
[10] SUN Maowen，OUYANG Xiaoping，MATTILA J，et al. Lightweight electrohydrostatic actuator drive solution for exoskeleton robots[J]. IEEE/ASME Transactions on Mechatronics，2022:1-12.
[11] 单开正，于海涛，韩亮亮，等. 近似直驱双足机器人跳跃运动非线性优化及试验验证[J]. 机械工程学报，2021，57(13):153-162，171. SHAN Kaizheng，YU Haitao，HAN Liangliang，et al. Nonlinear optimization and experimental validation of a quasi-direct-drive bipedal robot’s jumping motion[J]. Journal of Mechanical Engineering，2021，57(13):153-162，171.
[12] Wensing P M，Wang A，Seok S，et al. Proprioceptive actuator design in the mit cheetah:Impact mitigation and high-bandwidth physical interaction for dynamic legged robots[J]. Ieee transactions on robotics，2017，33(3):509-522.
[13] Bledt G，Powell M J，Katz B，et al. MIT Cheetah 3:Design and control of a robust, dynamic quadruped robot[C]//2018 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS). Madrid:International Conference on Intelligent Robots and Systems (IROS)，2018，2245-2252.
[14] Huang T H，Zhang S，Yu S，et al. Modeling and stiffness-based continuous torque control of lightweight quasi-direct-drive knee exoskeletons for versatile walking assistance[J]. IEEE Transactions on Robotics，2022，38(3)，1442-1459.
[15] Nesler C，Thomas G，Divekar N，et al. Enhancing voluntary motion with modular, backdrivable, powered hip and knee orthoses[J]. IEEE Robotics and Automation Letters，2022，7(3):6155-6162.
[16] Yu S，Huang T H，Yang X，et al. Quasi-direct drive actuation for a lightweight hip exoskeleton with high backdrivability and high bandwidth[J]. IEEE/ASME Transactions on Mechatronics，2020，25(4):1794-1802.
[17] Singh A，Kashiri N，Tsagarakis N. Design of a quasi-direct-drive actuator for dynamic motions[J]. Multidisciplinary Digital Publishing Institute Proceedings，2020，64(1):11.
[18] Katz B，Di C J，Kim S. Mini cheetah:A platform for pushing the limits of dynamic quadruped control[C]//2019 International Conference on Robotics and Automation (ICRA). Montreal:International Conference on Robotics and Automation (ICRA)，2019:6295-6301.
[19] Reichert T，Nussbaumer T，Kolar J W. Torque scaling laws for interior and exterior rotor permanent magnet machines[C/CD]//IEEE International Magnetics Conference 2009，Sacramento，CA，USA May 4-8，2009.
[20] 董夏林. 分数槽集中绕组永磁电机研究[D]. 南京:东南大学，2015. DONG Xialin. Research on permanent magnet machine with fractional slot concentrated windings[D]. Nanjing:Southeast University，2015.
[21] 唐任远. 现代永磁电机理论与设计[M]. 北京:机械工业出版社，2016.TANG Renyuan. Modern permanent magnet machines:theory and design[M]. Beijing:China Machine Press，2016.
[22] 徐玉婷. 四足机器人用关节电机设计与分析[D]. 杭州:浙江大学，2020.XU Yuting. Design and analysis of permanent magnet motors for quadruped robot[D]. Hangzhou:Zhejiang University，2020.
[23] 鲍和云. 两级星型齿轮传动系统分流特性及动力学研究[D]. 南京:南京航天航空大学，2006.BAO Heyun. Study on load-split characteristics and dynamics of two-stage star gear trains[D]. Nanjing:Nanjing University of Aeronautics and Astronautics，2006.
[24] 庞中华，崔红. 系统辨识与自适应控制MATLAB仿真[M]. 北京:北京航空航天大学出版社，2013.PANG Zhonghua，CUI Hong. Matlab simulation of system identification and adaptive control[M]. Beijing:Beijing University of Aeronautics and Astronautics Press，2013
[25] 黎宝梁. 采煤用低速大转矩永磁电机的设计与研究[D]. 沈阳:沈阳工业大学，2018. LI Baoliang. Design and research of low speed and large torque permanent magnet motor for coal mining[D]. Shenyang:Shenyang University of Technology，2018.

高扭矩密度仿人机器人驱动单元研究

Research on High Torque Density Drive Unit for Humanoid Robots

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	史彪飞, 刘忠韬, 孟宪夫, 魏中康, 张伟东, 魏恒. 单电机前驱电动汽车低速辅助转向控制研究[J]. 机械工程学报, 2026, 62(8): 125-138.
[2]	安海涛, 贾博韬, 王亮, 吴金涛, 潘松, 赵盖. 空间中空型超声电机的动力学仿真分析与极端环境试验研究[J]. 机械工程学报, 2026, 62(7): 269-283.
[3]	李丹阳, 林勇刚, 顾亚京, 刘宏伟, 徐志良, 付德义. 大型风电机组地面测试台导向加载静压支承技术[J]. 机械工程学报, 2026, 62(4): 309-317.
[4]	姚帅, 戴巨川, 吕伟荣. 基于频率法的风电机组混合塔筒拉索索力检测技术研究[J]. 机械工程学报, 2026, 62(2): 385-396.
[5]	张宁, 吴志豪, 张浩彬, 李普, 徐利伟, 殷国栋. 考虑车辆系统动力学与轮胎滑移能耗的车辆编队纵向协调控制[J]. 机械工程学报, 2025, 61(8): 250-260.
[6]	肖钊, 曹智辉, 邓杰文, 段书用, 赵前程, 戴巨川, 陶洁. 融合光纤传感数据与门控循环神经网络的风电机组载荷预测方法[J]. 机械工程学报, 2025, 61(8): 272-282.
[7]	吕航, 商显赫, 赵长禄, 韩雪峰, 杨占华, 张付军. 弱混车辆分层约束的能量协调控制策略[J]. 机械工程学报, 2025, 61(6): 268-276.
[8]	杨磊鹏, 王以磊, 王开政, 潘柏松, 肖渊. 介电层表面微结构3D打印构筑与摩擦纳米发电机性能研究[J]. 机械工程学报, 2025, 61(23): 270-279.
[9]	张永顺, 王莉, 吴振华, 刘高仁. 永磁球型电机目标方位的旋转磁矢量补偿控制[J]. 机械工程学报, 2025, 61(22): 36-46.
[10]	高天雄, 杨柳, 姚旭东, 肖守文, 艾超, 孔祥东. 高速湿式永磁无刷直流电机多目标优化设计[J]. 机械工程学报, 2025, 61(20): 339-348.
[11]	侯圣文, 周长江, 夏宁伟, 董凡. 高速减速器传动效率计算模型与试验[J]. 机械工程学报, 2025, 61(19): 54-62.
[12]	林世权, 张弛, 刘检华. 摩擦起电机理、调控与应用研究的现状及展望[J]. 机械工程学报, 2025, 61(19): 112-125.
[13]	李臻, 黄浩程, 李思语, 任慧敏, 何志祝, 盛磊. 高扭矩密度轴向磁通双PCB定子电机设计[J]. 机械工程学报, 2025, 61(19): 249-262.
[14]	王玉静, 李祎然, 康守强, 刘连胜, 李玉庆, 孙宇林. 基于数字孪生的不同工况下谐波减速器故障诊断方法[J]. 机械工程学报, 2025, 61(18): 12-26.
[15]	王嘉, 葛曼哲, 王子铭, 张露予, 王崇帅. 服役工况下基于电流信号的工业机器人谐波减速器故障建模[J]. 机械工程学报, 2025, 61(18): 366-377.