• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (18): 299-310.doi: 10.3901/JME.260738

• 材料科学与工程 • 上一篇    

扫码分享

铝合金T型筋薄壁筒双向旋挤成形机制研究

熊凌枫1,2, 樊晓光1,2, 詹梅1,2, 周达科3, 白丹妮1,2, 满谦4   

  1. 1. 西北工业大学材料学院 西安 710072;
    2. 西北工业大学陕西省高性能精确成形技术与装备重点实验室 西安 710072;
    3. 北京卫星制造厂有限公司 北京 100190;
    4. 火箭军成都局驻西安地区第二军事代表室 西安 710199
  • 收稿日期:2025-10-29 修回日期:2026-05-15 发布日期:2026-11-20
  • 作者简介:熊凌枫,男,2002年出生,博士研究生。主要研究方向为机器学习与功能结构材料;E-mail:xlf@mail.nwpu.edu.cn;詹梅(通信作者),女,1972 年出生,博士,博士研究生导师。主要研究方向为高性能轻量化薄壁复杂构件精确塑性成形制造理论、技术与 装备。E-mail:zhanmei@nwpu.edu.cn

Mechanism of Biaxial Spinning-Extrusion Forming Thin-Walled Cylinders with Aluminum Alloy T-Ribs

XIONG Lingfeng1,2, FAN Xiaoguang1,2, ZHAN Mei1,2, ZHOU Dake3, BAI Danni1,2, MAN Qian4   

  1. 1. School of Material Science and Engineering, Northwestern Polytechnical University, Xi'an 710072;
    2. Shaanxi Key Laboratory of High-Performance Precision Forming Technology and Equipment, School of Materials Science and Engineering, Xi'an 710072;
    3. Beijing Satellite Manufacturing Co., Ltd., Beijing 100190;
    4. The Second Military Representative Office of Chengdu Bureau of Rocket Force in Xi'an Area, Xi'an 710199
  • Received:2025-10-29 Revised:2026-05-15 Published:2026-11-20

摘要: 环向T型筋薄壁筒整体塑性成形是先进航空航天装备轻量化低成本制造的急需。针对T型筋筒成形困难的难题,本文提出了双向旋挤成形新原理:以旋压平台为基础,通过主旋轮轴向加载和辅助旋轮径向加载,成形T型筋结构。基于有限元仿真和实验,分析了旋挤成形材料变形特征、流动规律,揭示了其成形机理。结果表明:主旋轮挤压作用使筋部材料同时沿径向和周向伸长而外流,辅助旋轮的径向约束使筋顶部产生剪切分流,更容易成形出筋翼板结构,但易带动筒壁材料产生径向和轴向的流动,从而产生扩径缺陷。通过研究扩径的成形机制发现:筋部材料的周向变形是产生扩径的关键,通过改变旋轮布局、提高摩擦因子和筒壁厚度可以增大变形约束和筋部材料流动阻力,从而有效抑制扩径。搭建了双向旋挤成形实验平台,实验获得了高厚比为7.2,筋翼板高厚比为5.3的T型筋筒样件,证明旋挤成形工艺是可行和实用的。研究结果为带环向T型筋薄壁筒旋挤成形提供了理论依据。

关键词: T型筋薄壁筒体, 双向旋挤成形, 扩径, 数值模拟

Abstract: The overall plastic forming of thin-walled cylinder with transverse T-shaped ribs is an urgent need for lightweight and low-cost manufacturing of advanced aerospace equipment. To address the difficulty in forming T-ribbed cylinders, this paper proposes a new biaxial spinning extrusion forming principle: based on the spinning platform, the T-shaped rib structure is formed by axial loading of the main spinning roller and radial loading of the auxiliary spinning roller. Using finite element simulation and experiments, the material deformation characteristics and flow behavior during spinning extrusion are analyzed, and the forming mechanism is revealed. The results show that the extrusion action of the main roller causes the rib material to elongate and flow outward in both the radial and circumferential directions, while the radial constraint of the auxiliary roller induces shear diversion at the rib top, making it easier to form the rib flange, but it tends to cause radial and axial transfer of the cylinder wall material, resulting in diameter expansion defects. Investigation of the expansion formation mechanism reveals that the circumferential deformation of the rib material is the key factor causing expansion. By changing the roller arrangement, increasing the friction factor and the cylinder wall thickness, the deformation constraint and the material flow resistance of the rib can be enhanced, thereby effectively suppressing expansion. A biaxial spinning extrusion forming experimental platform was built, and a qualified T-shaped rib tube sample with a high thickness ratio of 7.2 and a high thickness ratio of 5.3 was obtained. It is proved that the biaxial spinning extrusion forming process is feasible and practical. The research results provide a theoretical basis for the spinning extrusion forming of thin-walled tubes with circumferential T-shaped ribs.

Key words: thin-walled tube with T ribs, biaxial spinning-extrusion forming, diameter expansion, numerical simulation

中图分类号: