• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (18): 287-298.doi: 10.3901/JME.260775

• 特邀专栏:大模型驱动的高端装备智能运维 • 上一篇    

扫码分享

变转速下基于改进MFCC-CWT与Cycle GAN的铣刀多源特征融合与故障诊断

张玉彦, 沈光辉, 李浩, 杜文辽, 王昊琪, 刘越洋   

  1. 郑州轻工业大学河南省高端装备智能制造重点实验室 郑州 450002
  • 收稿日期:2025-11-03 修回日期:2026-06-03 发布日期:2026-11-20
  • 作者简介:张玉彦,男,1989年出生,博士,副教授,硕士研究生导师。主要研究方向为深度学习、信号分析、多模态融合。E-mail:Zhangyuyan@zzuli.edu.cn;杜文辽(通信作者),男,1977年出生,博士,教授,博士研究生导师。主要研究方向为机械故障诊断、智能运维。E-mail:dwenliao@zzuli.edu.cn
  • 基金资助:
    国家自然科学基金(52105536,52275138)、高校科技创新人才团队(25HASTIT036,26IRTSTHN039,25IRTSTHN024)、河南省科技攻关(242102241029)和河南省重点研发专项(231111221100)资助项目。

Multi-source Feature Fusion and Tool Fault Diagnosis under Variable Spindle Speeds Based on Improved MFCC-CWT and Cycle GAN

ZHANG Yuyan, SHEN Guanghui, LI Hao, DU Wenliao, WANG Haoqi, LIU Yueyang   

  1. Zhengzhou University of Light Industry, Henan Provincial Key Laboratory of Intelligent Manufacturing of High-End Equipment, Zhengzhou 450002
  • Received:2025-11-03 Revised:2026-06-03 Published:2026-11-20

摘要: 针对变转速下铣刀故障诊断性能显著退化问题,提出一种基于改进MFCC-CWT与循环一致性生成对抗网络(Cycle-consistent generative adversarial network, Cycle GAN)的铣刀多源特征融合与故障诊断方法。包括三方面改进:构建动静梅尔频率倒谱系数(Mel frequency cepstral coefficients, MFCC)与增强连续小波变换(Continuous wavelet transform, CWT)特征图,实现声音与振动信号关键信息的联合表征;在嵌入卷积注意力模块的残差网络中对多模态特征进行自适应融合,提升故障模式的判别能力;将条件约束引入Cycle GAN实现不同转速下特征分布对齐。基于自建三轴机床平台,在12 000 r/min、15 000 r/min和18 000 r/min三种转速及五类铣刀状态下共采集9 000组多源数据进行验证。所提方法在12 000 r/min下诊断准确率达到99.40%,迁移到15 000 r/min和18 000 r/min时方法的准确率由69.03%和44.47%分别提升至95.97%和93.63%,在10 dB强噪声下仍保持95.03%的准确率。

关键词: 铣刀故障诊断, 多源信号融合, 动静MFCC, 增强CWT

Abstract: To address the significant degradation of milling cutter fault diagnosis performance under variable spindle speed conditions,a multi-source feature fusion and fault diagnosis method for milling cutters based on improved MFCC-CWT and cycle-consistent generative adversarial network (Cycle GAN) is proposed. The method includes three aspects of improvement: dynamic-static mel frequency cepstral coefficients (MFCC) and enhanced continuous wavelet transform (CWT) feature maps are constructed to realize the joint representation of key information from acoustic and vibration signals; multimodal features are adaptively fused in a residual network embedded with a convolutional attention module to improve the discriminative ability for fault modes; conditional constraints are introduced into Cycle GAN to align feature distributions under different spindle speeds. Based on a self-built three-axis machine tool platform,a total of 9 000 groups of multi-source data were collected under three spindle speeds of 12 000 r/min,15 000 r/min,and 18 000 r/min,as well as five milling cutter states,for validation. The proposed method achieves a diagnosis accuracy of 99.40% at 12 000 r/min. When transferred to 15 000 r/min and 18 000 r/min,the accuracy of the method is improved from 69.03% and 44.47% to 95.97% and 93.63%,respectively,and an accuracy of 95.03% is still maintained under strong noise of 10 dB.

Key words: tool fault diagnosis, multi-source signal fusion, dynamic-static MFCC, enhanced CWT

中图分类号: