电热处理对湿热环境作用下碳纤维环氧复合材料的损伤机制

doi:10.3901/JME.2017.18.064

机械工程学报 ›› 2017, Vol. 53 ›› Issue (18): 64-70.doi: 10.3901/JME.2017.18.064

电热处理对湿热环境作用下碳纤维环氧复合材料的损伤机制

刘登俊¹, 关庆丰¹, 王志平², 路鹏程², 李娜², 吕鹏¹

1. 江苏大学材料科学与工程学院镇江 212013;
2. 中国民航大学天津市民用航空器适航与维修重点实验室天津 300300

收稿日期:2016-05-18 修回日期:2016-12-21 出版日期:2017-09-20 发布日期:2017-09-20
通讯作者: 吕鹏(通信作者),男,1985年出生,副研究员.主要研究方向为载能束表面改性与微观结构.E-mail:lvp@ujs.edu.cn
作者简介:刘登俊,男1991年出生.主要研究方向为湿热、电热环境下复合材料微观结构与性能退化.E-mail:947026434@qq.com
基金资助:
国家自然科学基金（61471364）、中国民航大学开放基金（151001A）、江苏省博士后基金（1501159B）和江苏大学高级人才科研启动基金（14JDG127）资助项目。

Damage Mechanism of Electrothermal Treatment on Carbon Fiber Epoxy Composites under Hygrothermal Environment

LIU Dengjun¹, GUAN Qingfeng¹, WANG Zhiping², LU Pengcheng², LI Na², LÜ Peng¹

1. College of Material Science and Engineering, Jiangsu University, Zhenjiang 212013;
2. Tianjin Key Laboratory for Civil Aircraft Airworthiness and Maintenance, Civil Aviation University of China, Tianjin 300300

Received:2016-05-18 Revised:2016-12-21 Online:2017-09-20 Published:2017-09-20

摘要/Abstract

摘要： 对T300/E51复合材料进行电热处理、湿热老化以及电热吸湿处理，从弯曲性能、吸湿率、基体化学结构、玻璃化转变温度、弯曲断口等方面揭示电热处理对湿热老化的影响机制。研究结果表明：原始试样经湿热处理后发生部分水解，4 A电热+湿热处理试样的后固化比较明显，6 A电热+湿热处理试样没有发生明显的变化。后固化作用引起的界面裂纹尺寸减小导致4 A电热试样的吸湿率下降；玻璃化转变温度的变化规律与弯曲性能的变化规律类似。详细的分析表明，T300/E51复合材料经电热处理后其损伤机制与传统的吸湿损伤机制有所不同，玻璃化转变温度代替吸湿率成为衡量复合材料性能变化的重要因素。微观结构分析显示电热处理产生的温度梯度和压缩应力使得基体微裂纹增多，再经湿热处理后，溶胀广泛存在于整个基体中，进而导致弯曲性能降低。

关键词: 电热处理, 湿热老化, 碳纤维/环氧树脂复合材料, 微观结构

Abstract: The T300/E51 composites are treated by electrothermal treatment, hygrothermal ageing and electrothermal moisture treatment. The effect of electrothermal treatment on the hygrothermal ageing is revealed from bending properties, moisture absorption rate, chemical structure of the matrix, glass transition temperature, bending fracture and etc. The results show that the original sample is hydrolyzed partially after the hydrothermal treatment, and the samples processed with 4 A electro-thermal and hydrothermal treatment have an obvious postcure effect, while there is no significant change in the samples after 6 A electro-thermal and hydrothermal treatment. The moisture absorption rate of 4 A heated sample is decreased due to the decrease of the size of interface cracks caused by postcure effect. The variation of glass transition temperature is similar to that of bending behavior. The detailed analysis reveals that, the damage mechanism of T300/E51 composites after electrothermal treatment is different from that of traditional moisture. The glass transition temperature becomes a primary factor to measure the performance of composite materials, instead of moisture absorption. Microstructure observations show that the micro-cracks are increased owing to the temperature gradient and compressive stress generated by the effect of electrothermal treatment. Additionally, the swelling occurs throughout the matrix after the subsequent hydrothermal treatment, which eventually leads to the decrease of the bending property.

Key words: carbon fiber/epoxy composite, electro-thermal treatment, hydrothermal aging, microstructure

中图分类号:

TB332

刘登俊, 关庆丰, 王志平, 路鹏程, 李娜, 吕鹏. 电热处理对湿热环境作用下碳纤维环氧复合材料的损伤机制[J]. 机械工程学报, 2017, 53(18): 64-70.

LIU Dengjun, GUAN Qingfeng, WANG Zhiping, LU Pengcheng, LI Na, LÜ Peng. Damage Mechanism of Electrothermal Treatment on Carbon Fiber Epoxy Composites under Hygrothermal Environment[J]. Journal of Mechanical Engineering, 2017, 53(18): 64-70.

参考文献

[1] 张厚江,陈五一,陈鼎昌. 碳纤维复合材料 (CFRP)钻孔出口缺陷的研究[J]. 机械工程学报,2004,40(7):150-155. ZHANG Houjiang,CHEN Wuyi,CHEN Dingchang. Defects in drilling carbon fibre-reinforced plastic plates[J]. Chinese Journal of Mechanical Engineering,2004,40(7):150-155.
[2] FERABOLI P,MILLER M. Damage resistance and tolerance of carbon/epoxy composite coupons subjected to simulated lightning strike[J]. Composites Part A:Applied Science and Manufacturing,2009,40(6):954-967.
[3] KAWAKAMI H,FERABOLI P. Lightning strike damage resistance and tolerance of scarf-repaired mesh-protected carbon fiber composites[J]. Composites Part A:Applied Science and Manufacturing,2011,42(9):1247-1262.
[4] CZEPIELA S A,MCMANUS H,HASTINGS D. Charging of composites in the space environment[J]. Journal of Spacecraft and Rockets,2000,37(5):556-560.
[5] BOGORAD A L,LIKAR J J,HERSCHITZ R. Charging of composites in space environment:Ground test data[J]. Nuclear Science,IEEE Transactions on,2007,54(6):1981-1984.
[6] CZEPIELA S A,MCMANUS H L,HASTINGS D. Measurement and tailoring of composite electrical properties[J]. Journal of Spacecraft and Rockets,2000,37(5):561-566.
[7] HIRANO Y,KATSUMATA S,IWAHORI Y,et al. Artificial lightning testing on graphite/epoxy composite laminate[J]. Composites Part A:Applied Science and Manufacturing,2010,41(10):1461-1470.
[8] 吴锦武,原海朋. 铺设角度对层合板结构声功率的影响分析[J]. 机械工程学报,2016,52(19):73-80. WU Jinwu,YUAN Haipeng. Influence of laying angle on acoustic radiation power of laminated composite plates[J]. Journal of Mechanical Engineering,2016,52(19):73-80.
[9] 中国航空工业总公司. HB 7401-1996 树脂基复合材料层合板湿热环境吸湿试验方法[S]. 北京:中国标准出版社,1996. Aviation Industry Corporation of China. HB 7401-1996 Test method for moisture absorption of polymer metrix composite material laminated plates in hygrothermal environment[S]. Beijing:Standards Press of China,1996.
[10] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会. GB/T 3356-2014定向纤维增强聚合物基复合材料弯曲性能试验方法[S]. 北京:中国标准出版社,2014. General Administration of Quality Supervision,Inspection and Quarantine of the People's Republic of China,Standardization Administration of the People's Republic of China. GB/T 3356-2014 Test method for flexural properties of orientational fiber reinforced polymer metrix composite materials[S]. Beijing:Standards Press of China,2014.
[11] 谢可勇,李晖,孙岩,等. 湿热老化对纤维增强树脂基复合材料性能的影响及其机理[J]. 机械工程材料,2014,38(8):1-5. XIE Keyong,LI Hui,SUN Yan,et al. Effect of hygrothermal aging on behaviors of fiber reinforced resin composites and its mechanism[J]. Materials for Mechanical Engineering,2014,38(8):1-5.
[12] ANDREW J J,ARUMUGAM V,SANTULLI C. Effect of post-cure temperature and different reinforcements in adhesive bonded repair for damaged glass/epoxy composites under multiple quasi-static indentation loading[J]. Composite Structures,2016(143):63-74.
[13] 刘廷栋,王乃昌,许鑫平. 环氧树脂的固化机理[J]. 热固性树脂,1989(2):38-48. LIU Tingdong,WANG Naichang,XU Xinping. Curing mechanism of epoxy resin[J]. Thermosetting Resin,1989(2):38-48.
[14] 李晓骏,许凤和,陈新文. 先进聚合物基复合材料的热氧老化研究[J]. 材料工程,1999(12):19-22. LI Xiaojun,XU Fenghe,CHEN Xinwen. Study of thermooxidizing aging of advanced polymer matrix composites[J]. Journal of Materials Engineering,1999(12):19-12.
[15] PAPANICOLAOU G C,KOSMIDOU T V,VATALIS A S,et al. Water absorption mechanism and some anomalous effects on the mechanical and viscoelastic behavior of an epoxy system[J]. Journal of Applied Polymer Science,2006,99(4):1328-1339.
[16] 路鹏程,毕亚芳,王志平,等. 电热作用对CFRP力学性能的影响[J]. 复合材料学报,2016,33(10):2223-2229. LU Pengcheng,BI Yafang,WANG Zhiping,et al. Effects of electric thermal effect on mechanical properties of carbon fiber reinforced polymer[J]. Acta Materiae Compositae Sinica,2016,33(10):2223-2229.
[17] 汪微微,赵建平. 平行偏置裂纹相互作用及其合并条件[J]. 南京工业大学学报,2009,31(4):27-31. WANG Weiwei,ZHAO Jianping. Interaction between offset parallel cracks and combination conditions[J]. Journal of Nanjing University of Technology,2009,31(4):27-31.

电热处理对湿热环境作用下碳纤维环氧复合材料的损伤机制

Damage Mechanism of Electrothermal Treatment on Carbon Fiber Epoxy Composites under Hygrothermal Environment

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 13

编辑推荐

Metrics

本文评价

[1]	秦瑶,李忠华,孙云龙. 纳米炭黑/XLPE复合绝缘热老化特性试验研究 ^*[J]. 电气工程学报, 2019, 14(3): 33-40.
[2]	王东, 赵军, 曹岩, 薛超. 微纳米复合陶瓷刀具材料计算机辅助设计和制备[J]. 机械工程学报, 2018, 54(7): 223-232.
[3]	陈旭斌, 葛翔, 祝毅, 杨华勇. 选择性激光熔化零件微观结构及摩擦学性能研究[J]. 机械工程学报, 2018, 54(3): 63-72.
[4]	刘净川, 姜风春, 王立权, 张蒙祺, 运飞宏. Ti-(SiC_f/Al₃Ti)层状复合材料在侵彻早期阶段基于NEIM的建模与仿真研究[J]. 机械工程学报, 2018, 54(22): 63-77.
[5]	徐明秀;陈章华;徐敏强;樊久铭. 疲劳过程中磁记忆信号变化的机理[J]. , 2014, 50(4): 53-59.
[6]	李媛;刘小君;张彦;刘焜. 面接触条件下织构表面摩擦特性研究[J]. , 2012, 48(19): 109-115.
[7]	王婷;王东坡;刘刚;龚宝明;宋宁霞. 40Cr超声表面滚压加工纳米化[J]. , 2009, 45(5): 177-183.
[8]	刘翠荣;孟庆森;鲁小莹;刘子建. ZrO2电解质陶瓷与Al的阳极键合连接机理分析[J]. , 2008, 44(5): 114-118.
[9]	罗彬宾;李祥;陈云飞. 超薄水膜剪切流的分子动力学模拟[J]. , 2007, 43(9): 119-121.
[10]	王志平;王吉孝;纪朝辉;李娜;陈亚军. 表面纳米化焊接接头组织和结构[J]. , 2007, 43(11): 154-159.
[11]	郑靖;陈捷;周仲荣. 四环素牙摩擦磨损行为的研究[J]. , 2005, 41(2): 158-161.
[12]	许晓静;施连杰;程晓农;蔡兰;吉平平. 40Cr钢低温超塑性的研究[J]. , 2004, 40(7): 141-144.
[13]	王顺才;李春志;边为民. 2024高强铝合金中等弥散相Al20Cu2Mn3结构的确定[J]. , 1990, 26(4): 16-19.