Research Progress in the Numerical Simulation of Heat and Mass Transfer during Wire Arc Additive Manufacturing

doi:10.3901/JME.2024.08.065

Abstract

Abstract: Wire Arc Additive Manufacturing (WAAM), which is able to create large metal components with high deposition rate and low equipment cost, has increasingly attracted attention from industrial sectors, including aerospace, shipbuilding, military equipment etc. During WAAM, the combined effects from arc characteristics, droplet transfer behaviour, molten pool flow and solidification, and heat accumulation under the complex thermal cycle plays a critical role in the deposition formation and quality, which also the theoretical basis of realizing the geometry and material properties in control. The emerging research on the numerical simulation of WAAM is reviewed in this article, and a comprehensive overview of the physical mechanism of WAAM based on different heat sources is also provided. The heat and mass transfer produced in different WAAM process are described to reveal their intrinsic connections. Common defects are depicted, including formation mechanism, inside factors, inhibition strategy. Methods for controlling the deposition process, geometry and quality are discussed, take into account the physical characteristics of WAAM. It is concluded in this paper that many challenges still exist in the numerical simulation of the WAAM process, and critical thinking and suggestions are proposed for its future development and application.

Key words: wire arc additive manufacturing, numerical model, heat and mass transfer, defect, quality control

CLC Number:

TG156

ZHANG Yunshu, WU Bintao, ZHAO Yun, DING Donghong, PAN Zengxi, LI Huijun. Research Progress in the Numerical Simulation of Heat and Mass Transfer during Wire Arc Additive Manufacturing[J]. Journal of Mechanical Engineering, 2024, 60(8): 65-80.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.2024.08.065

http://www.cjmenet.com.cn/EN/Y2024/V60/I8/65

References

[1] SPANIOL E，UNGETHüM T，TRAUTMANN M，et al. Development of a novel tig hot-wire process for wire and arc additive manufacturing[J]. Welding in The World，2020，64(8)：1329-1340.
[2] HEJRIPOUR F，VALENTINE D T，AIDUN D K. Study of mass transport in cold wire deposition for wire arc additive manufacturing [J]. International Journal of Heat and Mass Transfer，2018，125：471-484.
[3] ARTAZA T，BHUJANGRAO T，SUáREZ A，et al. Influence of heat input on the formation of laves phases and hot cracking in plasma arc welding (paw) additive manufacturing of inconel 718 [J]. Metals，2020，10(6)：771-788.
[4] GARCíA-GARCíA V，CAMACHO-ARRIAGA J C，REYES-CALDERóN F. A simplified elliptic paraboloid heat source model for autogenous gtaw process[J]. International Journal of Heat and Mass Transfer，2016，100：536-549.
[5] ZHANG B，WANG C，WANG Z，et al. Microstructure and properties of AL alloy er5183 deposited by variable polarity cold metal transfer[J]. Journal of Materials Processing Technology，2019，267：167-176.
[6] MUKHERJEE T，MANVATKAR V，DE A，et al. Mitigation of thermal distortion during additive manufacturing[J]. Scripta Materialia，2017，127：79-83.
[7] CHAO Y P，QI L H，ZUO H S，et al. Remelting and bonding of deposited aluminum alloy droplets under different droplet and substrate temperatures in metal droplet deposition manufacture[J]. International Journal of Machine Tools and Manufacture，2013，69：38-47.
[8] LIU M，YI H，CAO H，et al. Heat accumulation effect in metal droplet-based 3d printing：evolution mechanism and elimination strategy[J]. Additive Manufacturing，2021，48：102413.
[9] ZHAO W，WEI Y，LONG J，et al. Modeling and simulation of heat transfer，fluid flow and geometry morphology in gmaw-based wire arc additive manufacturing [J]. Welding in the World，2021，65(8)：1571-1590.
[10] YANG D，WANG G，ZHANG G. Thermal analysis for single-pass multi-layer gmaw based additive manufacturing using infrared thermography[J]. Journal of Materials Processing Technology，2017，244：215-224.
[11] LIU Z，QI H. Effects of substrate crystallographic orientations on crystal growth and microstructure formation in laser powder deposition of nickel-based superalloy[J]. Acta Materialia，2015，87：248-258.
[12] RADHAKRISHNAN B，GORTI S，BABU S S. Large scale phase field simulations of microstructure evolution during thermal cycling of Ti-6Al-4V[C]//Proceeding International Conference on Solid-Solid Phase Transformations in Inorganic Materials (PTM) Whistler，2015.
[13] PRABHAKAR P，SAMES W J，DEHOFF R，et al. Computational modeling of residual stress formation during the electron beam melting process for Inconel 718[J]. Additive Manufacturing，2015，7：83-91.
[14] MUKHERJEE T，DEBROY T. Printability of 316 stainless steel[J]. Science and Technology of Welding and Joining，2019，24(12)：1-8.
[15] MUKHERJEE T，DEBROY T. A digital twin for rapid qualification of 3d printed metallic components[J]. Applied Materials Today，2019，14：59-65.
[16] PARK H J，RHEE S，KANG M J，et al. Joining of steel to aluminum alloy by ac pulse mig welding[J]. Materials Transactions，2009，50(9)：2314-2317.
[17] KUMAR R，DILTHEY U，DWIVEDI D K，et al. Thin sheet welding of Al 6082 alloy by AC pulse-GMA and AC wave pulse-gma welding[J]. Materials & Design，2009，30(2)：306-313.
[18] BAI X，COLEGROVE P，DING J，et al. Numerical analysis of heat transfer and fluid flow in multilayer deposition of paw-based wire and arc additive manufacturing[J]. International Journal of Heat and Mass Transfer，2018，124：504-516.
[19] YIN X，GOU J，ZHANG J，et al. Numerical study of arc plasmas and weld pools for gtaw with applied axial magnetic fields[J]. Journal of Physics D：Applied Physics，2012，45(28)：285203-285215.
[20] YANG Y，ZHOU X，LI Q，et al. A computationally efficient thermo-mechanical model for wire arc additive manufacturing [J]. Additive Manufacturing，2021，46：100955.
[21] DING D，PAN Z，CUIURI D，et al. Wire-feed additive manufacturing of metal components：technologies，developments and future interests[J]. The International Journal of Advanced Manufacturing Technology，2015，81(1-4)：465-481.
[22] PATTANAYAK S，SAHOO S K. Gas metal arc welding based additive manufacturing—a review[J]. CIRP Journal of Manufacturing Science and Technology，2021，33：398-442.
[23] NORRISH J，POLDEN J，RICHARDSON I. A review of wire arc additive manufacturing：development，principles，process physics，implementation and current status[J]. Journal of Physics D：Applied Physics，2021，54(47)：473001.
[24] CHO D W，NA S J，CHO M H，et al. A study on v-groove gmaw for various welding positions[J]. Journal of Materials Processing Technology，2013，213(9)：1640-1652.
[25] E SILVA R H G，DOS SANTOS PAES L E，OKUYAMA M P，et al. Tig welding process with dynamic feeding：a characterization approach[J]. The International Journal of Advanced Manufacturing Technology，2018，96(9-12)：4467-4475.
[26] XU W H，LIN S B，FAN C L，et al. Statistical modelling of weld bead geometry in oscillating arc narrow gap all-position gma welding[J]. The International Journal of Advanced Manufacturing Technology，2014，72(9-12)：1705-1716.
[27] XU W H，LIN S B，FAN C L，et al. Prediction and optimization of weld bead geometry in oscillating arc narrow gap all-position gma welding[J]. The International Journal of Advanced Manufacturing Technology，2015，79(1-4)：183-196.
[28] LV S X，XU Z W，WANG H T，et al. Investigation on tig cladding of copper alloy on steel plate[J]. Science and Technology of Welding and Joining，2013，13(1)：10-16.
[29] OGINO Y，HIRATA Y. Numerical simulation of metal transfer in argon gas-shielded GMAW[J]. Welding in the World，2015，59：465-473.
[30] KADOTA K，HIRATA Y. Numerical model of metal transfer using an electrically conductive liquid[J]. Weld World，2021，55：50-55.
[31] DUTRA J C，CIRINO L M，GONçALVES E SILVA R H. AC–gtaw of aluminium–new perspective for evaluation of role of positive polarity time[J]. Science and Technology of Welding and Joining，2013，15(7)：632-637.
[32] CHEN J，ZHANG Y，WU C，et al. Suppression of undercut defects in high-speed gmaw through a compound magnetic field[J]. Journal of Materials Processing Technology，2019，274：1-11.
[33] WU H，CHANG Y，LU L，et al. Review on magnetically controlled arc welding process[J]. The International Journal of Advanced Manufacturing Technology，2017，91(9-12)：4263-4273.
[34] XIAO L，FAN D，HUANG J K. Numerical study on arc plasma behaviors in gmaw with applied axial magnetic field[J]. Journal of the Physical Society of Japan，2019，88(7)：473001.
[35] CHEN J，HAN Z，WANG L，et al. Influence of arc interactions on heat and mass transfer during a two-arc hybrid welding[J]. International Journal of Heat and Mass Transfer，2020，148：119058.
[36] WANG X，FAN D，HUANG J，et al. A unified model of coupled arc plasma and weld pool for double electrodes tig welding[J]. Journal of Physics D：Applied Physics，2014，47(27)：202-275.
[37] WANG X，FAN D，HUANG J，et al. Numerical simulation of arc plasma and weld pool in double electrodes tungsten inert gas welding [J]. International Journal of Heat and Mass Transfer，2015，85：924-934.
[38] LI Y，SU C，ZHU J. Comprehensive review of wire arc additive manufacturing：hardware system，physical process，monitoring，property characterization，application and future prospects[J]. Results in Engineering，2021，13：100330.
[39] Fang M，Chandra S，Park C B. Experiments on remelting and solidification of molten metal droplets deposited in vertical columns[J]. Manuf. Sci. Eng. -Trans. Asm.，2007，129(2)：311-318.
[40] HU J，TSAI H L. Heat and mass transfer in gas metal arc welding. part II：the metal [J]. International Journal of Heat and Mass Transfer，2007，50(5-6)：808-820.
[41] XU G，HU J，TSAI H L. Modeling three-dimensional plasma arc in gas tungsten arc welding[J]. Journal of Manufacturing Science and Engineering，2012，134：1-12.
[42] JIAN X，WU C S. Numerical analysis of the coupled arc–weld pool–keyhole behaviors in stationary plasma arc welding[J]. International Journal of Heat and Mass Transfer，2015，84：839-847.
[43] HU J，TSAI H L. Heat and mass transfer in gas metal arc welding. part I：the arc[J]. International Journal of Heat and Mass Transfer，2007，50(5-6)：833-846.
[44] XU G，HU J，TSAI H L. Three-dimensional modeling of arc plasma and metal transfer in gas metal arc welding[J]. International Journal of Heat and Mass Transfer，2009，52(7-8)：1709-1724.
[45] Zhu F L，Tsai H L. A comprehensive model on the transport phenomena during gas metal arc welding process[J]. Progress in Computational Fluid Dynamics，2004，37：99-117.
[46] ZHAO Y，CHUNG H. Numerical simulation of droplet transfer behavior in variable polarity gas metal arc welding[J]. International Journal of Heat and Mass Transfer，2017，111：1129-1141.
[47] PAN J，HU S，YANG L，et al. Simulation and analysis of heat transfer and fluid flow characteristics of variable polarity gtaw process based on a tungsten–arc-specimen coupled model[J]. International Journal of Heat and Mass Transfer，2016，96：346-352.
[48] ZHANG Z，WU C. Effect of fluid flow in the weld pool on the numerical simulation accuracy of the thermal field in hybrid welding[J]. Journal of Manufacturing Processes，2015，20：215-223.
[49] KOMEN H，SHIGETA M，TANAKA M. Numerical simulation of molten metal droplet transfer and weld pool convection during gas metal arc welding using incompressible smoothed particle hydrodynamics method[J]. International Journal of Heat and Mass Transfer，2018，121：978-985.
[50] TRAUTMANN M，HERTEL M，FÜSSEL U. Numerical simulation of tig weld pool dynamics using smoothed particle hydrodynamics[J]. International Journal of Heat and Mass Transfer，2017，115：842-853.
[51] CADIOU S，COURTOIS M，CARIN M，et al. 3D heat transfer，fluid flow and electromagnetic model for cold metal transfer wire arc additive manufacturing (CMT-WAAM)[J]. Additive Manufacturing，2020，36：101541.
[52] TRAIDIA A，ROGER F，GUYOT E，et al. Hybrid 2d–3d modelling of GTA welding with filler wire addition[J]. International Journal of Heat and Mass Transfer，2012，55(15-16)：3946-3963.
[53] ZHOU X，ZHANG H，WANG G，et al. Three-dimensional numerical simulation of arc and metal transport in arc welding based additive manufacturing[J]. International Journal of Heat and Mass Transfer，2016，103：521-537.
[54] OU W，MUKHERJEE T，KNAPP G L，et al. Fusion zone geometries，cooling rates and solidification parameters during wire arc additive manufacturing[J]. International Journal of Heat and Mass Transfer，2018，127：1084-1094.
[55] NGUYEN T C，WECKMAN D C，JOHNSON D A，et al. High speed fusion weld bead defects[J]. Science and Technology of Welding and Joining，2013，11(6)：618-633.
[56] LIU J W，RAO Z H，LIAO S M，et al. Numerical investigation of weld pool behaviors and ripple formation for a moving GTA welding under pulsed currents[J]. International Journal of Heat and Mass Transfer，2015，91：990-1000.
[57] HU J，GUO H，TSAI H L. Weld pool dynamics and the formation of ripples in 3d gas metal arc welding[J]. International Journal of Heat and Mass Transfer，2008，51(9-10)：2537-2552.
[58] Rao Z H，Zhou J，Liao S M，et al. Three-dimensional modeling of transport phenomena and their effect on the formation of ripples in gas metal arc welding[J]. Journal of Applied Physics，2010，107(5)：101541.
[59] MENG X，QIN G，BAI X，et al. Numerical analysis of undercut defect mechanism in high speed gas tungsten arc welding[J]. Journal of Materials Processing Technology，2016，236：225-234.
[60] ZONG R，CHEN J，WU C，et al. Numerical analysis of molten metal behavior and undercut formation in high-speed gmaw[J]. Journal of Materials Processing Technology，2021，297：117-266.
[61] WU D，HUA X，YE D，et al. Understanding of humping formation and suppression mechanisms using the numerical simulation[J]. International Journal of Heat and Mass Transfer，2017，104：634-643.
[62] CHO M H，FARSON D F. Understanding bead hump formation in gas metal arc welding using a numerical simulation[J]. Metallurgical and Materials Transactions B，2007，38(2)：305-319.
[63] XU G，CAO Q，HU Q，et al. Modelling of bead hump formation in high speed gas metal arc welding[J]. Science and Technology of Welding and Joining，2016，21(8)：700-710.
[64] MENG X，QIN G，ZOU Z. Investigation of humping defect in high speed gas tungsten arc welding by numerical modelling[J]. Materials & Design，2016，94：69-78.
[65] MENG X，QIN G，ZONG R. Thermal behavior and fluid flow during humping formation in high-speed full penetration gas tungsten arc welding[J]. International Journal of Thermal Sciences，2018，134：380-391.
[66] MENG X，QIN G. A theoretical study of molten pool behavior and humping formation in full penetration high-speed gas tungsten arc welding[J]. International Journal of Heat and Mass Transfer，2019，132：143-153.
[67] WANG L，WU C，CHEN J，et al. Influence of the external magnetic field on fluid flow，temperature profile and humping bead in high speed gas metal arc welding[J]. International Journal of Heat and Mass Transfer，2018，116：1282-1291.
[68] ABE T，SASAHARA H. Development of the shell structures fabrication cam system for direct metal lamination using arc discharge-lamination height error compensation by torch feed speed control[J]. International Journal of Precision Engineering and Manufacturing，2015，16(1)：171-176.
[69] 陈克选，王向余，李宜炤，等. 水冷条件下WAAM温度场的数值模拟研究[J]. 材料导报，2021，35(4)：165-169. CHEN Kexuan，WANG Xiangyu，LI Yizhao，et al. Numerical simulation of waam temperature field under water-cooled conditions[J]. Materials Report，2021，35(4)：165-169.
[70] DASILVAL J，SOUZA D M，DE ARAÚJO D B，et al. Concept and validation of an active cooling technique to mitigate heat accumulation in WAAM[J]. The International Journal of Advanced Manufacturing Technology，2020，107(5-6)：2513-2523.
[71] ABE T，KANEKO J I，SASAHARA H. Thermal sensing and heat input control for thin-walled structure building based on numerical simulation for wire and arc additive manufacturing[J]. Additive Manufacturing，2020，35：101357.
[72] LI F，CHEN S，SHI J，et al. Thermoelectric cooling-aided bead geometry regulation in wire and arc-based additive manufacturing of thin-walled structures[J]. Applied Sciences，2018，8(2)：207.
[73] 韩文涛，林健，雷永平，等. 不同层间停留时间下电弧增材制造2Cr13薄壁件热力学行为[J]. 焊接学报，2019，40(12)：47-52. HAN Wentao，LIN Jian，LEI Yongping，et al. Thermodynamic behavior of wire arc additive manufacturing of 2Cr13 thin-walled parts under different interlayer residence times[J]. Transactions of the China Welding Institution，2019，40(12)：47-52.
[74] 张天雷，徐刚，沈艳涛，等. 基于MIG的电弧增材制造不同层间停留时间温度场仿真模拟[J]. 智能计算机与应用，2020，10(5)：251-256. ZHANG Tianlei，XU Gang，SHEN Yantao，et al. Numerical simulation of thermal behavior of different interlayer idle time for MIG-based additive manufacturing[J]. Light Industry Machinery，2020，10(5)：251-256.
[75] MONTEVECCHI F，VENTURINI G，GROSSI N，et al. Idle time selection for wire-arc additive manufacturing：A finite element-based technique[J]. Additive Manufacturing，2018，21：479-486.
[76] HACKENHAAR W，MAZZAFERRO J A E，MONTEVECCHI F，et al. An experimental-numerical study of active cooling in wire arc additive manufacturing[J]. Journal of Manufacturing Processes，2020，52：58-65.
[77] MONTEVECCHI F，VENTURINI G，GROSSI N，et al. Heat accumulation prevention in wire-arc-additive- manufacturing using air jet impingement[J]. Manufacturing Letters，2018，17：14-18.
[78] WU B，PAN Z，CHEN G，et al. Mitigation of thermal distortion in wire arc additively manufactured Ti6Al4V part using active interpass cooling[J]. Science and Technology of Welding and Joining，2019，24(5)：484-494.
[79] 高溟江，樊丁，侯英杰，等. 随弧激冷对电弧增材制造温度场及组织性能的影响[J]. 电焊械，2021，51(8)：105-110. GAO Mingjiang，FAN Ding，HOU Yingjie，et al. Influence of trailing cooling on temperature field and microstructure properties of wire arc additive manufacturing[J]. Electric Welding Machine，2021，51(8)：105-110.