制冷剂溶解性对连杆轴承润滑特性的影响研究

doi:10.3901/JME.2021.15.146

机械工程学报 ›› 2021, Vol. 57 ›› Issue (15): 146-159.doi: 10.3901/JME.2021.15.146

扫码分享

制冷剂溶解性对连杆轴承润滑特性的影响研究

胡健锋¹, 金华强¹, 顾江萍¹, 黄跃进¹, 孙哲¹, 王新雷², 沈希¹

1. 浙江工业大学机械工程学院杭州 310032;
2. 伊利诺伊大学香槟校区农业与生物工程学院厄巴纳IL61801 美国

收稿日期:2020-08-10 修回日期:2020-12-01 出版日期:2021-08-05 发布日期:2021-11-03
通讯作者: 沈希(通信作者),男,1966年出生,博士,教授,博士研究生导师。主要研究方向为热力学系统计算机测量评价与优化控制。E-mail:sx@zjut.edu.cn
作者简介:胡健锋,男,1996年出生。主要研究方向为小型全封闭制冷压缩机可靠性建模与评价。E-mail:749898442@qq.com
基金资助:
浙江省重点研发计划（2020C04010）和浙江省基础公益研究计划（LGG19E050020，LGG18E050024）资助项目。

Research on the Effect of Refrigerant Solubility on the Lubrication Characteristics of Connecting Rod Bearings

HU Jianfeng¹, JIN Huaqiang¹, GU Jiangping¹, HUANG Yuejin¹, SUN Zhe¹, WANG Xinlei², SHEN Xi¹

1. College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310032;
Department of Agricultural and Biological Engineering, University of Illinois at Urbana-Champaign, Urbana IL 61801, USA

Received:2020-08-10 Revised:2020-12-01 Online:2021-08-05 Published:2021-11-03

摘要/Abstract

摘要： 制冷压缩机中实际的润滑环境为非纯油状态下的混合润滑，制冷剂溶解于润滑油会导致压缩机连杆轴承的润滑性能下降，目前尚未对其展开深入研究。以制冷剂R600a/矿物油Azmol混合液相为润滑介质，建立基于制冷剂溶解度的润滑模型，研究不同负荷工况下溶解度对小型制冷压缩机连杆轴承润滑特性的影响规律。研究结果表明：在不同工况下，考虑溶解度影响后，轴承最小油膜厚度最大减小18.51%，最大油膜压力最大增加7.08%，摩擦功耗最大下降19.90%，端泄流量最大增加29.62%。该溶解度润滑模型为小型制冷压缩机连杆轴承摩擦副的失效机理分析提供了新的思路，对压缩机过负荷工况设计、轴承间隙及环境温度控制具有重要的指导意义。

关键词: 小型制冷压缩机, 连杆轴承, 溶解度, 润滑特性, 过负荷工况

Abstract: The actual lubrication environment in refrigeration compressors is mixed lubrication in the state of impure oil. The refrigerant dissolves in the lubricating oil will cause the lubricating performance of the connecting rod bearings of the compressor to decline. At present, no in-depth research has been carried out on it. The refrigerant R600a/Azmol mineral oil mixed liquid phase is used as the lubricating medium to establish a lubrication model based on the solubility of the refrigerant, and to study the effect of solubility on the lubrication characteristics of the connecting rod bearings of small refrigeration compressors under different load conditions. The results show that under different working conditions, after considering the effect of solubility, the minimum oil film thickness of the bearing is reduced by a maximum of 18.51%, the maximum oil film pressure is increased by a maximum of 7.08%, the friction power consumption is decreased by a maximum of 19.90%, and the end discharge flow is increased by a maximum of 29.62%. The solubility lubrication model provides a new idea for the analysis of the failure mechanism of the connecting rod bearing friction pair of small refrigeration compressors, and has important guiding significance for the compressor overload condition design, bearing clearance and environmental temperature control.

Key words: small refrigeration compressor, connecting rod bearing, solubility, lubrication characteristics, overload condition

中图分类号:

TB652

胡健锋, 金华强, 顾江萍, 黄跃进, 孙哲, 王新雷, 沈希. 制冷剂溶解性对连杆轴承润滑特性的影响研究[J]. 机械工程学报, 2021, 57(15): 146-159.

HU Jianfeng, JIN Huaqiang, GU Jiangping, HUANG Yuejin, SUN Zhe, WANG Xinlei, SHEN Xi. Research on the Effect of Refrigerant Solubility on the Lubrication Characteristics of Connecting Rod Bearings[J]. Journal of Mechanical Engineering, 2021, 57(15): 146-159.

参考文献

[1] ZHANG Jie, DONG Qiangbing. Lubrication performance analysis of crankshaft bush in compressor[J]. Engineering Failure Analysis, 2018, 90:277-289.
[2] 聂涛, 刘振明, 刘楠, 等. 内燃机径向滑动轴承润滑特性及影响因素研究[J]. 计算机仿真, 2019, 36(1):270-274. NIE Tao, LIU Zhenming, LIU Nan, et al. Research on the lubrication characteristics and influencing factors of the journal bearing in internal combustion engine[J]. Computer Integrated Manufacturing Systems, 2019, 36(1):270-274.
[3] 毕凤荣, 刘博, 刘春朝, 等. 基于热弹流模型的柴油机连杆小头轴承润滑研究[J]. 内燃机工程, 2018, 39(4):15-22. BI Fengrong, LIU Bo, LIU Chunchao, et al. Research on diesel engine connecting rod small end bearing lubrication based on thermal elastic hydrodynamic model[J]. Chinese Internal Combustion Engine Engineering, 2018, 39(4):15-22.
[4] ILMAN M N, BARIZY R A. Failure analysis and fatigue performance evaluation of a failed connecting rod of reciprocating air compressor[J]. Engineering Failure Analysis, 2015, 56:142-149.
[5] STROZZI A, BALDINI A, GIACOPINI M, et al. A repertoire of failures in connecting rods for internal combustion engines, and indications on traditional and advanced design methods[J]. Engineering Failure Analysis, 2016, 60:20-39.
[6] SINGH N, AWASTHI R K, SINGH D, et al. Modeling and simulation of bearing clearance effects on journal center motion trajectories[J]. Materials Today:Proceedings, 2018, 5(9):17585-17596.
[7] PROFITO F J, ZACHARIADIS D C, DINI D. Partitioned fluid-structure interaction techniques applied to the mixed-elastohydrodynamic solution of dynamically loaded connecting-rod big-end bearings[J]. Tribology International, 2019, 140:105767.
[8] LEE K H, KIM J W, HUH Y J, et al. Optimum design of dynamically-loaded journal bearing with R600a refrigerant application[C]//International Compressor Engineering Conference, 1998:1232.
[9] GRANDO F P, PRIEST M, PRATA A T. Lubrication in refrigeration systems:Numerical model for piston dynamics considering oil-refrigerant interaction[J]. Proceedings of the Institution of Mechanical Engineers, Part J:Journal of Engineering Tribology, 2006, 220(3):245-258.
[10] 史正良, 郭小青, 胡余生, 等. 冷冻机油与制冷剂的溶解特性研究[J]. 制冷与空调, 2017(9):30-33. SHI Zhengliang, GUO Xiaoqing, HU Yusheng, et al. Research on miscibility characteristics of refrigeration oil and refrigerant[J]. Refrigeration and Air-Conditioning, 2017(9):30-33.
[11] WANG Chuang, XING Ziwen, HOU Feng, et al. Research on axis orbit of the journal bearing lubricated with oil and refrigerant mixtures in a twin-screw refrigeration compressor[J]. International Journal of Refrigeration, 2018, 90:1-11.
[12] ZHELEZNY V P, SCRIPOV V P. Determination of the pseudocritical parameters for refrigerant/oil solutions[J]. Fluid Phase Equilibria, 2003, 212(1-2):285-302.
[13] ZHELEZNY V P, PROCENKO D A, ANCHERBAK S N. An experimental investigation and modelling of the thermodynamic properties of isobutane-compressor oil solutions:Some aspects of experimental methodology[J]. International Journal of Refrigeration, 2007, 30(3):433-445.
[14] ZHELEZNY V P, SECHENYH V V, SEMENYUK Y V, et al. An experimental investigation and modelling of the viscosity refrigerant/oil solutions[J]. International Journal of Refrigeration, 2009, 32(6):1389-1395.
[15] 吴建华, 雷源, 王刚, 等. 往复式冰箱压缩机曲轴动态特性与轴承润滑计算分析[J]. 西安交通大学学报, 2015, 49(2):55-61. WU Jianhua, LEI Yuan, WANG Gang, et al. Numerical analysis for the crankshaft's dynamic behavior and bearing lubrication of reciprocating refrigerator compressor[J]. Journal of Xi'an Jiaotong University, 2015, 49(2):55-61.
[16] 郎骥, 杨建刚, 曹浩, 等. 滑动轴承热效应分析及流场等效温度的合理确定[J]. 润滑与密封, 2012, 37(10):70-73. LANG Ji, YANG Jiangang, CAO Hao, et al.Thermal effect analysis and fluid field average temperature reasonable determination of journal bearing[J]. Lubrication Engineering, 2012, 37(10):70-73.
[17] PONT A, LOPEZ J, RIGOLA J, et al. Numerical dynamic analysis of reciprocating compressor mechanism:Parametric studies for optimization purposes[J]. Tribology International, 2017, 105:1-14.
[18] 胡启龙, 何文强, 管文生, 等. 滑动轴承内轴颈涡动引发的热效应分析[J]. 热能动力工程, 2020, 35(9):22-28. HU Qilong, HE Wenqiang, GUAN Wensheng, et al. Analysis on thermal effect caused by journal whirl in sliding bearing[J]. Journal of Engineering for Thermal Energy and Power, 2020, 35(9):22-28.

制冷剂溶解性对连杆轴承润滑特性的影响研究

Research on the Effect of Refrigerant Solubility on the Lubrication Characteristics of Connecting Rod Bearings

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

本文评价

[1]	朱军超, 钱海俣, 郑良焱, 朱汉华. 考虑应力偶计入区间及黏压效应的倾斜轴承非牛顿流体润滑特性研究[J]. 机械工程学报, 2021, 57(9): 139-146.
[2]	王晓红, 裴世源, 常山. 划痕对椭圆瓦轴承润滑特性及转子稳定性的影响[J]. 机械工程学报, 2021, 57(11): 256-264.
[3]	裴世源, 牛红军, 洪军. 快堆钠泵动静压导轴承润滑特性分析[J]. 机械工程学报, 2020, 56(21): 29-37.
[4]	裴世源, 郑文斌, 洪军. 剪切稀化对径向滑动轴承润滑特性的影响[J]. 机械工程学报, 2020, 56(1): 100-109.
[5]	张艳芹, 倪世钱, 张志全, 孔鹏睿, 冯雅楠, 孔祥滨. 变黏度静压滑动轴承高速时油膜动态润滑特性[J]. 机械工程学报, 2019, 55(21): 108-117.
[6]	张国涛, 童宝宏, 尹延国, 解挺. 环面接触复层多孔轴承热流体动压润滑性能及生/传热机制分析[J]. 机械工程学报, 2019, 55(21): 98-107.
[7]	李直, 陈剑, 沈锦龙, 刘焜. 线接触滚/滑状态下表面形貌的弹性变形研究[J]. 机械工程学报, 2018, 54(5): 142-148.
[8]	肖华平;刘书海;郭丹;路新春;雒建斌. 高接触压力下齿轮油润滑特性[J]. , 2011, 47(1): 89-95.
[9]	王晓力;刘伟;朱克勤. 基于微极性流体润滑的有限长动载轴承特性研究[J]. , 2004, 40(10): 35-38.
[10]	张朝辉;温诗铸;雒建斌. 薄膜润滑的微极流体模拟[J]. , 2001, 37(9): 4-8.