• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2020, Vol. 56 ›› Issue (21): 29-37.doi: 10.3901/JME.2020.21.029

• 特邀专栏:核能装备设计制造及服役 • 上一篇    下一篇

扫码分享

快堆钠泵动静压导轴承润滑特性分析

裴世源1, 牛红军2, 洪军1   

  1. 1. 西安交通大学现代设计与转子轴承系统教育部重点实验室 西安 710049;
    2. 沈阳鼓风机集团核电泵业有限公司 沈阳 110869
  • 收稿日期:2019-11-22 修回日期:2020-06-16 出版日期:2020-11-05 发布日期:2020-12-19
  • 作者简介:裴世源(通信作者),男,1983年出生,博士,副研究员。主要研究方向为滑动轴承与转子动力学。E-mail:peishiyuan@xjtu.edu.cn
  • 基金资助:
    国家自然科学基金资助项目(51975456,51605367)。

Lubrication Characteristics of Hybrid Bearing in Sodium-cooled Fast Reactor

PEI Shiyuan1, NIU Hongjun2, HONG Jun1   

  1. 1. Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi'an Jiaotong University, Xi'an 710049;
    2. Nuclear Pump Co. Ltd, Shenyang Blower Works Group Corporation, Shenyang 110869
  • Received:2019-11-22 Revised:2020-06-16 Online:2020-11-05 Published:2020-12-19

摘要: 快堆钠泵导轴承的润滑介质、工作原理以及润滑状态与传统滑动轴承均有显著不同,目前关于该类轴承的研究鲜有报道。为对钠泵导轴承设计和运行维护提供理论支撑,为以某快堆钠泵工程样机的内反馈轴承为研究对象,考虑紊流和动静压耦合关系等因素,建立了其润滑分析模型,采用自编有限元程序求解得到了典型工况下轴承的动静特性,分析了工况参数与关键结构参数对其润滑特性的影响。结果发现:钠液黏度低、密度大,紊流对液膜的润滑性能具有重要影响;当偏心率小于0.6时,主要由静压起主导作用,当偏心率大于0.6时,动压作用不可忽略,非线性效应增强;间隙增加最小油膜厚度线性增加、流量显著加大、稳定性下降;入口扬程增加,静压作用增强,流量增加,稳定性增强,典型工况下入口扬程应大于50 m才能保证轴承的高可靠性。

关键词: 快中子反应堆, 钠泵, 润滑特性, 动静压轴承, 内反馈

Abstract: The lubricant, working principle and lubrication regime of the guide bearing of the main pump in the sodium-cooled fast reactor are significantly different from conventional film bearing. The lubrication analysis model of the hybrid bearing is established with considering turbulence and pressure-coupling effects. The dynamic and static characteristics of the bearing are obtained by using self-coded finite element code. The working conditions and key geometrical parameters on its lubrication characteristics are systematically analyzed. It is found that the viscosity of sodium liquid is very low and the density is high, so the turbulence has significant effects on the lubrication performance. Moreover, when the eccentricity ratio is less than 0.6, hydrostatic effect plays a leading role, whereas the hydrodynamic effect cannot be ignored when the eccentricity ratio is greater than 0.6. Furthermore, when the bearing clearance increases, the minimum film thickness and the flow rate increases, while the stability decreases. When the inlet head increase, the hydrostatic effect is enhanced, and both the flowrate and the stability increase. The inlet head should be more than 50 meters to ensure the high reliability.

Key words: fast neutron reactor, sodium pump, lubrication characteristic, hybrid bearing, internal feedback

中图分类号: