基于DOE的大型下架体铸钢件铸造工艺优化研究*

doi:10.3901/JME.2017.06.088

机械工程学报 ›› 2017, Vol. 53 ›› Issue (6): 88-93.doi: 10.3901/JME.2017.06.088

扫码分享

基于DOE的大型下架体铸钢件铸造工艺优化研究^*

向青春¹, 张伟¹, 邱克强¹, 孙治国¹, 孙爱新², 杨桂星²

1. 沈阳工业大学材料科学与工程学院沈阳 110870；
2. 沈阳铸锻工业有限公司铸钢分公司沈阳 110142

出版日期:2017-03-20 发布日期:2017-03-20
作者简介:向青春(通信作者)，男，1972年出生，副教授。主要研究方向为材料成形工艺及过程控制。E-mail：xiangqchun@yeah.net
基金资助:
* 沈阳市科技计划资助项目(F13-036-2-00); 20160318收到初稿，20160904收到修改稿;

Casting Process Optimization for Large Lower Frame Body of Heavy Gyratory Crusher Based on DOE

XIANG Qingchun¹, ZHANG Wei¹, QIU Keqiang¹, SUN Zhiguo¹, SUN Aixin, YANG Guixing

1. School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870;
2. Steel Casting Branch Company, Shenyang Foundry and Forging Industry Co., Ltd., Shenyang 110142

Online:2017-03-20 Published:2017-03-20

摘要/Abstract

摘要：

特大型旋回破碎机下架体铸件生产中产生大量的缩孔缩松缺陷，无法满足质量要求。经研究认为，该铸件产生的缩孔缺陷主要由铸件的内圈冒口类型、内圈和外圈冒口是否添加补贴及补贴类型、浇注温度等因素决定。采用Taguchi试验设计(Design of experiment， DOE)方法，以铸件缩孔体积最小和工艺出品率最高作为试验指标，以内圈冒口类型、内圈补贴、外圈补贴和浇注温度作为影响因子，设计L₉(3⁴)正交试验方案，通过ProCAST软件对9组试验方案进行模拟并分析结果，获得了该铸件的最优铸造工艺为内圈用4个圆柱形发热冒口补缩、内圈和外圈均添加补贴、在1 560 ℃浇注。实际浇注验证结果表明，采用DOE法对该大型铸钢件的铸造工艺优化在最大程度上减少了缩孔缩松的产生，同时也提高了铸造工艺出品率。

关键词: DOE, 工艺出品率, 缩孔, 正交试验, 大型铸钢件

Abstract: In the casting of the large lower frame bodies for heavy gyratory crushers, many shrinkage defects are frequently generated in these steel castings, so the quality of them cannot be satisfied. The research indicates that whether the shrinkage defects are formed in them is mainly dependent on the process parameters such as the type of risers on the inner part of the casting, the pads of risers on the inner and outer parts of the casting, the type of riser pads, and the pouring temperature. Based on the principle of design of experiment (DOE), considering the above-mentioned four process parameters as the influence factors, a L9(34) orthogonal test scheme was designed to optimize the casting process of the large lower frame body for heavy gyratory crushers, aiming at two test indexes, i.e. the volume of casting shrinkage defects to be minimal and the process yield to be maximal. With the CAE software of ProCAST, nine groups of casting process programs in the L9 (34) orthogonal test scheme were calculated and simulated. By analyzing the simulation results, the optimized casting process was put forward for the large lower frame body of the heavy gyratory crusher, i.e. the inner part of the casting is fed with four cylindrical exothermic risers, the pads of risers are used both on the inner and outer parts of the casting, and the pouring temperature is 1 560 ℃. And the results of the practical casting experiments show that it can not only reduce the shrinkage defects to the greatest extent but also improve the process yield by using DOE method to optimize the foundry process of this large steel casting.

Key words: design of experiment, orthogonal test, process yield, shrinkage defect, large steel casting

向青春, 张伟, 邱克强, 孙治国, 孙爱新, 杨桂星. 基于DOE的大型下架体铸钢件铸造工艺优化研究^*[J]. 机械工程学报, 2017, 53(6): 88-93.

XIANG Qingchun, ZHANG Wei, QIU Keqiang, SUN Zhiguo, SUN Aixin, YANG Guixing. Casting Process Optimization for Large Lower Frame Body of Heavy Gyratory Crusher Based on DOE[J]. Journal of Mechanical Engineering, 2017, 53(6): 88-93.

参考文献

[1] 聂小武. 铸钢件缩孔及缩松缺陷的消除[J]. 铸造，2007，56(1)：57-59.
        NIE Xiaowu. Elimination the porosity and shrinkage of steel castings[J]. Foundry，2007，56(1)：57-59.
[2] 邢文滨，王文祥. 补浇冒口对防止缩孔产生的作用[J].铸造设备与工艺，2012，194(1)：18-20.
        XING Wenbin，WANG Wenxiang. Effect of filling riser on preventing shrinkage[J]. Foundry Equipment and Technology，2012，194(1)：18-20.
[3] 黄天佑，刘小刚，康进武，等. 我国大型铸钢件生产的现状与关键技术[J]. 铸造，2007，56(9)：899-904.
        HUANG Tianyou，LIU Xiaogang，KANG Jinwu，et al. The review of the production status of heavy steel castings and key technologies for their manufacturing in China[J]. Foundry，2007，56(9)：899-904.
[4] 马晓辉，刘红军. 温度场凝固模拟在大型铸钢件中的应用[J]. 铸造技术，2012，33(7)：846-848.
        MA Xiaohui，LIU Hongjun. Application of solidification simulation of temperature field in heavy steel casting[J]. Foundry Technology，2012，33(7)：846-848.
[5] SENTHILKUMA B，PONNAMBALAM S G，JAWAHAR N. Process factor optimization for controlling pull-down defects in iron castings[J]. Journal of Materials Processing Technology，2009，209(1)：554-560.
[6] VERRAN G O，MENDESB R P K，DALLA VALENTINA L O V. DOE applied to optimization of aluminum alloy die castings[J]. Journal of Materials Processing Technology，2008，200(1-3)：120-125.
[7] 倪计民，高旭男，石秀勇，等. 基于多目标优化的柴油机VNT-vEGR系统开发研究[J]. 机械工程学报，2016，52(2)：108-115.
     NI Jimin，GAO Xunan，SHI Xiuyong，et al. Study on the development of diesel engine VNT-vEGR system based on multi-objective optimization[J]. Journal of Mechanical Engineering，2016，52(2)：108-115.
[8] 秦飞，夏国峰，高察，等. 基于数值模拟的多圈QFN封装热疲劳可靠性试验设计方案[J]. 机械工程学报，2014，50(18)：92-98.
     QIN Fei，XIA Guofeng，GAO Cha，et al. Design of experiment methodology for thermal fatigue reliability of multi-row QFN packages based on numerical simulations[J]. Journal of Mechanical Engineering，2014，50(18)：92-98.
[9] SUN Y，LUO J，MI G F，et al. Numerical simulation and defect elimination in the casting of truck rear axle using a nodular cast iron[J]. Materials and Design，2011，32(3)：1623-1629.
[10] GUNASEGARAM D R，FARNSWORTH D J，NGUYEN T T. Identification of critical fa

[1]	陈巍巍, 石文泽, 卢超, 程进杰, 陈尧, 陈果. 高温锻件在线快速检测螺旋线圈EMAT优化设计[J]. 机械工程学报, 2022, 58(10): 12-23.
[2]	王建磊, 门川皓, 赵伟刚, 贾谦, 崔亚辉, 张琛, 袁小阳. 动静压机械密封的结构设计及端面槽型优化研究[J]. 机械工程学报, 2021, 57(9): 108-117.
[3]	崔颖, 于颖嘉, 王永亮, 赵爽, 钟兢军. 一种梁式管接头密封性能与结构参数敏感性分析[J]. 机械工程学报, 2021, 57(3): 147-155.
[4]	刘宗超, 吴林辉, 陈贡发. 几何参数对主动脉支架生物力学性能的影响[J]. 机械工程学报, 2021, 57(11): 112-119.
[5]	宫岛, 刘广宇, 周劲松, 孙煜, 尤泰文. 动车组车体异常振动问题分析及治理研究[J]. 机械工程学报, 2021, 57(10): 95-105,117.
[6]	段亮, 宋春元, 刘闯, 吴金贤. 动力学参数对出口铁路客车扭曲试验的影响[J]. 机械工程学报, 2019, 55(6): 116-121.
[7]	刘可心, 王蕾, 刘佳磊, 金松哲. Ti₂AlN薄膜的制备及性能表征[J]. 机械工程学报, 2019, 55(16): 77-84.
[8]	钱小辉, 马骁妍, 秦中华, 侯少静, 徐美杭, 张鹏, 朱自安. 基于正交试验的玻璃壳热应力影响因素分析[J]. 机械工程学报, 2019, 55(12): 91-98.
[9]	刘洪鹏, 严儒井, 王玉忠, 王擎. 几何特性对风力机翼型粗糙度敏感性的影响[J]. 机械工程学报, 2018, 54(14): 198-206.
[10]	徐文涛, 廖敬波, 张泽通, 陈永杰, 唐光武. 基于参数识别的桥梁冲击系数随机响应优化方法[J]. 机械工程学报, 2018, 54(12): 64-70.
[11]	李晓东, 韩硕, 王存宇, 常颖, 胡平, 董瀚. 第三代汽车钢温热成形工艺研究及性能评价[J]. 机械工程学报, 2017, 53(8): 35-42.
[12]	陈波, 高殿荣, 杨超, 毋少峰, 张光通. 大功率远程射雾器结构参数多目标智能协同优化^*[J]. 机械工程学报, 2017, 53(6): 166-175.
[13]	丁智平, 黄达勇, 荣继刚, 黄友剑, 曾家兴. 注塑成型短玻纤增强复合材料各向异性弹性常数预测方法[J]. 机械工程学报, 2017, 53(24): 126-134.
[14]	孙治国, 任英磊, 向青春, 张伟, 杨桂星, 邱克强. 强制风冷在大型铸钢件砂芯上的应用[J]. 机械工程学报, 2017, 53(22): 67-73.
[15]	应锐, 喻俊志, 王卫兵, 张亭, 冯静安, 杜晟. 细颗粒分级复合型水力旋流器结构及工艺参数的优化研究^*[J]. 机械工程学报, 2017, 53(2): 124-134.

基于DOE的大型下架体铸钢件铸造工艺优化研究^*

Casting Process Optimization for Large Lower Frame Body of Heavy Gyratory Crusher Based on DOE

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价