• CN:11-2187/TH
  • ISSN:0577-6686

›› 2012, Vol. 48 ›› Issue (20): 77-82.

• 论文 • 上一篇    下一篇

四辊轧机非常态轧制时板形模型的研究

白振华;韩林芳;李经洲;马续创;石晓东;张青树   

  1. 燕山大学机械工程学院;燕山大学亚稳材料制备技术与科学国家重点实验室;上海梅山钢铁股份有限公司冷轧厂
  • 发布日期:2012-10-20

Research of the Plate-shaped Model of Four-roll Mill when Rolling under Asymmetric State

BAI Zhenhua;HAN Linfang;LI Jingzhou;MA Xuchuang;SHI Xiaodong;ZHANG Qingshu   

  1. College of Mechanical Engineering, Yanshan University State Key Laboratory of Metastable Materials Science and Technology, Yanshan University Cold Rolling Mill of Shanghai Meishan Iron and Steel Co., Ltd.
  • Published:2012-10-20

摘要: 针对四辊轧机工作过程中可能出现的上下左右不对称问题,在大量的现场试验与理论研究的基础上,充分结合四辊轧机的设备与非常态轧制的工艺特点,从辊系弹性变形模型入手,充分考虑到四辊轧机非常态轧制过程中的上下与左右的不对称性,建立一套适合于四辊轧机非常态轧制时的板形模型,编制相应的板形分析与控制软件,利用该模型及软件不但可以定量预报出带材跑偏、不对称辊型、轧制中心线与轧辊中心线不重合、不对称弯辊、不对称窜辊等非常态因素单独或综合作用对轧机成品板形的影响,而且可以定量预报出对称弯辊、对称窜辊、倾辊等常态因素对成品板形的影响。该模型及软件已经被应用到梅钢1420双机架平整机组的板形分析与控制,有效地提高了机组的成品板形质量,板形封闭率从项目开展前的2.5%降低到目前的0.5%以内,给机组创造了较大的经济效益,具有进一步推广应用的价值。

关键词: 板形, 非常态轧制, 辊系弹性变形, 四辊轧机

Abstract: In order to deal with the problem of up-down and left-right asymmetry that may occur up in the four-roll mill work process, on the basis of a large number of field trials and theoretical study and fully integrating the process characteristics of the equipment and asymmetric state rolling of the four-roll mill and considering the asymmetry of up-down and left-right, the model of elastic deformation of the roll system is used to establish a set of plate-shaped model which suits for four-roll mill when it works. The corresponding analysis and control software of the strip shape is also drawn up. It can quantitative forecast not only effects caused alone or comprehensively by asymmetry factors such as strip drift, asymmetric roller type, rolling centerline and roll not coincidence, asymmetric centerline bending roll, asymmetric motion of roll, but also effects caused alone or comprehensively by symmetrical factors such as symmetric bending roll, symmetric motion of roll and tilting roller on the influence of the finished product plate shape. The model and software is directly applied to the analysis and control of the shape of Meigang 1420 double frame flat plate to improve the shape quality of finished products. Now the closed rate of strip shape has reduced from 2.5% before to less than 0.5% .It has created unit large economic benefits and has further application value.

Key words: Asymmetric state rolling, Elastic deformation of the roll system, Four-high mill, Shape

中图分类号: