新型振动辅助粉末输送系统增材制造钴基合金/铜合金界面互锁结构

doi:10.3901/JME.2024.23.278

机械工程学报 ›› 2024, Vol. 60 ›› Issue (23): 278-293.doi: 10.3901/JME.2024.23.278

扫码分享

新型振动辅助粉末输送系统增材制造钴基合金/铜合金界面互锁结构

唐锦荣¹, 王迪¹, 刘林青¹, 谭华², 李扬¹, 周伟³, 陈国星⁴, 杨永强¹

1. 华南理工大学机械与汽车工程学院广州 510641;
2. 西北工业大学凝固技术国家重点实验室西安 710072;
3. 厦门大学机电工程系厦门 361005;
4. 苏州热工研究院有限公司苏州 215004

收稿日期:2023-12-13 修回日期:2024-06-08 出版日期:2024-12-05 发布日期:2025-01-23
作者简介:唐锦荣，男，1999年出生。主要研究方向为金属增材制造。E-mail：tangjr0228@163.com;王迪(通信作者)，男，1986年出生，博士，教授，博士研究生导师。主要研究方向为增材制造与激光加工技术开发与应用。E-mail：mewdlaser@scut.edu.cn
基金资助:
国家重点研发计划(2022YFB4600303)、国家自然科学基金(52073105)、广东省基础与应用基础研究基金(2022B1515120025)和中央高校基本科研业务费专项基金(2022ZYGXZR009)资助项目。

Additive Manufacturing of Co-based Alloy/copper Interface Interlocking Structures with a New Vibration-assisted Powder Delivery System

TANG Jinrong¹, WANG Di¹, LIU Linqing¹, TAN Hua², LI Yang¹, ZHOU Wei³, CHEN Guoxing⁴, YANG Yongqiang¹

1. School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510641;
2. State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi'an 710072;
3. Department of Mechanical &Electrical Engineering, Xiamen University, Xiamen 361005;
4. Suzhou Nuclear Power Research Institute, Suzhou 215004

Received:2023-12-13 Revised:2024-06-08 Online:2024-12-05 Published:2025-01-23

摘要/Abstract

摘要： 多材料激光粉末床熔融(Laser powder bed fusion,LPBF)成形过程中，高质量的粉末输送对于保证成形稳定性并提升零件的成形质量具有重要意义。设计了一种新型超声振动辅助粉末输送系统，分析了振动辅助模块的频率特征，并研究了针头直径对落粉效果的影响，通过0.3 mm直径的针头实现了稳定、良好的粉末输送效果。通过上述粉末输送系统LPBF成形三种具有不同界面互锁结构(齿形、正弦、矩形)的钴基合金/铜多材料零件，验证了该粉末输送系统的可行性。进一步研究了三种不同互锁结构的界面特征，分析了界面处宏观样貌、微观缺陷以及元素分布。结果表明，振动辅助模块在21 kHz频率下能正常落粉，成形零件界面出现了两种金属的混合区。齿形互锁结构的成形质量优于正弦与矩形结构，其界面处的材料结合良好。以上结果能为粉末输送系统设计以及金属多材料界面结构设计提供参考。

关键词: 激光粉末床熔融, 多材料, 粉末输送, 互锁结构

Abstract: In the process of multi-material laser powder bed fusion (LPBF), a high-quality powder delivery is critical for the stability of the LPBF process and enhancing the quality of parts. A new type of ultrasonic vibration-assisted powder delivery system is designed. The frequency characteristics of the vibration-assisted module and the effect of needle diameter on powder dropping are investigated. A needle with a size of 0.3 mm is demonstrated to achieve the stale and well powder delivery. Three types of Co-based alloy/copper multi-material parts with different interlocking structures (i.e., sawtooth, sine, and rectangle) are fabricated by LPBF using the ultrasonic vibration-assisted powder delivery system, demonstrating the feasibility of the powder delivery system. Subsequently, the interface characteristics of three types of multi-material parts are investigated to analyze the macroscopic morphology, defects and the element distribution at the interface. The results show that the powder can be delivered stably with a frequency of 21 kHz by the vibration-assisted module. A mixing area of two materials are found at the interface of the multi-material parts. The forming quality of the sawtooth-shaped interlocking structure is higher than that of the sine- and rectangle- shaped interlocking structures, which showing a good interfacial bonding. The results may provide reference for the design of the powder delivery system and the metal multi-material interface structure.

Key words: laser powder bed fusion, multi-material, powder delivery, interlocking structure

中图分类号:

TG665

唐锦荣, 王迪, 刘林青, 谭华, 李扬, 周伟, 陈国星, 杨永强. 新型振动辅助粉末输送系统增材制造钴基合金/铜合金界面互锁结构[J]. 机械工程学报, 2024, 60(23): 278-293.

TANG Jinrong, WANG Di, LIU Linqing, TAN Hua, LI Yang, ZHOU Wei, CHEN Guoxing, YANG Yongqiang. Additive Manufacturing of Co-based Alloy/copper Interface Interlocking Structures with a New Vibration-assisted Powder Delivery System[J]. Journal of Mechanical Engineering, 2024, 60(23): 278-293.

参考文献

[1] WANG Di，DENG Guowei，YANG Yongqiang，et al. Research progress on additive manufacturing of metallic heterogeneous materials[J]. Journal of Mechanical Engineering，2021，57(1)：186.
[2] MARQUES A，CUNHA Â，GASIK M，et al. Inconel 718–copper parts fabricated by 3D multi-material laser powder bed fusion： a novel technological and designing approach for rocket engine[J]. The international journal of advanced manufacturing technology，2022，122(3–4)：2113-2123.
[3] WEI C，SUN Z，CHEN Q，et al. Additive manufacturing of horizontal and 3d functionally graded 316l/cu10sn components via multiple material selective laser melting[J]. Journal of Manufacturing Science and Engineering，2019，141(8)：081014.
[4] BARTOLOMEU F，COSTA M M，ALVES N，et al. Additive manufacturing of niti-ti6al4v multi-material cellular structures targeting orthopedic implants[J]. Optics and Lasers in Engineering，2020，134：106208.
[5] WITS W W，AMSTERDAM E. Graded structures by multi-material mixing in laser powder bed fusion[J]. CIRP Annals，2021，70(1)：159-162.
[6] 刘芳,刘常升,陶兴启，等. 结晶器铜板上激光熔覆镍基合金[J]. 东北大学学报，2006(10)：1106-1109. LIU Fang，LIU Changsheng，TAO Xingqi，er al. Ni-based alloy cladding on cpooer crystallizer surface by laser[J]. Journal of Northeastern University,2006(10)：1106-1109
[7] XIAO Y，SUN C，WU X，et al. Restoration of pure copper motor commutator for aviation by laser powder deposition[J]. Journal of Materials Research and Technology，2023，23：5796-5806.
[8] 李胜鑫. 铜钢熔敷焊接特点及其缺陷控制[J]. 电焊机，2013，43(6)：56-58，98. LI Shengxin. Characteristics and defects control of copper and steel re-melt deposit welding[J]. Electric Welding Machine，2013，43(6)： 56-58，98.
[9] DOLEV O，OSOVSKI S，SHIRIZLY A. Ti-6al-4v hybrid structure mechanical properties—wrought and additive manufactured powder-bed material[J]. Additive Manufacturing，2021，37：101657.
[10] CHEN J，YANG Y，SONG C，et al. Interfacial microstructure and mechanical properties of 316l /cusn10 multi-material bimetallic structure fabricated by selective laser melting[J]. Materials Science and Engineering： A，2019，752： 75-85.
[11] BAI Y，ZHANG J，ZHAO C，et al. Dual interfacial characterization and property in multi-material selective laser melting of 316L stainless steel and C52400 copper alloy[J]. Materials Characterization，2020，167：110489.
[12] WANG D，LIU L，DENG G，et al. Recent progress on additive manufacturing of multi-material structures with laser powder bed fusion[J]. Virtual and Physical Prototyping，2022，17(2)：329-365.
[13] AL-JAMAL O M，HINDUJA S，LI L. Characteristics of the bond in cu–h13 tool steel parts fabricated using SLM[J]. CIRP Annals，2008，57(1)：239-242.
[14] ZHANG X，WEI C，CHUEH Y H，et al. An integrated dual ultrasonic selective powder dispensing platform for three-dimensional printing of multiple material metal/glass objects in selective laser melting[J]. Journal of Manufacturing Science and Engineering，2019，141(1)： 011003.
[15] YUAN Y，YU K，ZHU H，et al. Continuous delivery of powders with vibration and pneumatic pressure assistance for laser-based additive manufacturing processes[J]. Journal of Manufacturing Processes，2022，82：336-346.
[16] WU H，PRITCHET D，WOLFF S，et al. A vibration-assisted powder delivery system for additive manufacturing - an experimental investigation -[J]. Additive Manufacturing，2020，34：101170.
[17] SING S L，LAM L P，ZHANG D Q，et al. Interfacial characterization of SLM parts in multi-material processing： Intermetallic phase formation between AlSi10Mg and C18400 copper alloy[J]. Materials Characterization，2015，107：220-227.
[18] WEI C，GU H，GU Y，et al. Abnormal interfacial bonding mechanisms of multi-material additive-manufactured tungsten–stainless steel sandwich structure[J]. International Journal of Extreme Manufacturing，2022，4(2)： 025002.
[19] CHEN J，YANG Y，WANG D，et al. Effect of manufacturing steps on the interfacial defects of laser powder bed fusion 316L/CuSn10[J]. Materials Letters，2021，292： 129377.
[20] WEI C，LIU L，GU Y，et al. Multi-material additive-manufacturing of tungsten - copper alloy bimetallic structure with a stainless-steel interlayer and associated bonding mechanisms[J]. Additive Manufacturing，2022，50：102574.
[21] CHEN K，WANG C，HONG Q，et al. Selective laser melting 316L/CuSn10 multi-materials：processing optimization，interfacial characterization and mechanical property[J]. Journal of Materials Processing Technology，2020，283：116701.
[22] VERMA S，YANG C K，LIN C H，et al. Additive manufacturing of lattice structures for high strength mechanical interlocking of metal and resin during injection molding[J]. Additive Manufacturing，2022，49： 102463.
[23] CHUEH Y H，WEI C，ZHANG X，et al. Integrated laser-based powder bed fusion and fused filament fabrication for three-dimensional printing of hybrid metal/polymer objects[J]. Additive Manufacturing，2020，31：100928.
[24] TANG S H，CHENG C W，YEH R Y，et al. Direct joining of 3D-printed thermoplastic parts to SLM-fabricated metal cellular structures by ultrasonic welding[J]. The International Journal of Advanced Manufacturing Technology，2018，99(1–4)：729-736.
[25] KELLY C N，WANG T，CROWLEY J，et al. High-strength，porous additively manufactured implants with optimized mechanical osseointegration[J]. Biomaterials，2021，279： 121206.
[26] 林书玉. 超声换能器的原理及设计[M]. 北京：科学出版社， 2004. LIN Shuyu. The principle and design of ultrasonic transducers[M]. Beijing：Science Press，2004.
[27] HARKNESS P，CARDONI A，RUSSELL J，et al. Designing a hollow langevin transducer for ultrasonic coring[J]. Applied Mechanics and Materials，2010，24-25： 65-70.
[28] ZHANG Guoqing，YANG Yongqiang，SONG Changhui，et al. Study on biocompatibility of cocrmo alloy parts manufactured by selective laser melting[J]. Journal of Medical and Biological Engineering，2018，38(1)： 76-86.
[29] CHEN J，YANG Y，BAI Y，et al. Single and multiple track formation mechanism of laser powder bed fusion 316L/CuSn10 multi-material[J]. Materials Characterization，2022，183：111654.
[30] CHEN J，YANG Y，SONG C，et al. Influence mechanism of process parameters on the interfacial characterization of selective laser melting 316L/CuSn10[J]. Materials Science and Engineering： A，2020，792：139316.
[31] LIU L，WANG D，YANG Y，et al. Effect of scanning strategies on the microstructure and mechanical properties of inconel 718 alloy fabricated by laser powder bed fusion[J]. Advanced Engineering Materials，2023，25(5)：2200492.
[32] CAO L. Mesoscopic-scale simulation of pore evolution during laser powder bed fusion process[J]. Computational Materials Science，2020，179：109686.
[33] WANG W，NING J，LIANG S Y. Analytical prediction of keyhole porosity in laser powder bed fusion[J]. The International Journal of Advanced Manufacturing Technology，2022，119(11–12)：6995-7002.
[34] NING J，WANG W，ZAMORANO B，et al. Analytical modeling of lack-of-fusion porosity in metal additive manufacturing[J]. Applied Physics A，2019，125(11)： 797.
[35] MUGWAGWA L，YADROITSAVA I，MAKOANA N W，et al. Residual stress in laser powder bed fusion[M]// Fundamentals of Laser Powder Bed Fusion of Metals. Elsevier，2021： 245-276.
[36] ZHANG Z，ZHAO X，TSUREKAWA S. Diffusion in copper/cobalt systems under high magnetic fields[J]. Materials，2021，14(11)：3104.
[37] SENTHILNATHAN N，RAJA ANNAMALAI A，VENKATACHALAM G. Effect of cobalt addition on the morphology and mechanical properties of W–Ni–Cu–Co alloy[J]. Emerging Materials Research，2019，8(4)： 558-566.
[38] ZURIGUEL I，GARCIMARTÍN A，MAZA D，et al. Jamming during the discharge of granular matter from a silo[J]. Physical Review E，2005，71(5)：051303.
[39] SINGH A，KAPIL S，DAS M. A comprehensive review of the methods and mechanisms for powder feedstock handling in directed energy deposition[J]. Additive Manufacturing，2020，35：101388.
[40] PANWISAWAS C，TANG Y T，REED R C. Metal 3D printing as a disruptive technology for superalloys[J]. Nature Communications，2020，11(1)：2327.
[41] GOKCEKAYA O，ISHIMOTO T，TODO T，et al. Effect of scan length on densification and crystallographic texture formation of pure chromium fabricated by laser powder bed fusion[J]. Crystals，2020，11(1)：9.
[42] YEUNG H，LANE B. A residual heat compensation based scan strategy for powder bed fusion additive manufacturing[J]. Manufacturing Letters，2020，25： 56-59.
[43] YAN H，WANG A，XU K，et al. Microstructure and interfacial evaluation of Co-based alloy coating on copper by pulsed Nd： YAG multilayer laser cladding[J]. Journal of Alloys and Compounds，2010，505(2)： 645-653.
[44] XIE Z，ZHANG C，WANG R，et al. Microstructure and wear resistance of WC/Co-based coating on copper by plasma cladding[J]. Journal of Materials Research and Technology，2021，15：821-833.
[45] CHEN S，LIANG J，LIU C，et al. Preparation of a novel Ni/Co-based alloy gradient coating on surface of the crystallizer copper alloy by laser[J]. Applied Surface Science，2011，258(4)：1443-1450.

新型振动辅助粉末输送系统增材制造钴基合金/铜合金界面互锁结构

Additive Manufacturing of Co-based Alloy/copper Interface Interlocking Structures with a New Vibration-assisted Powder Delivery System

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

本文评价

[1]	商帅, 杨建军, 孙鹏, 李政豪, 王洛唯, 李红珂, 张厚超, 王瑞, 孙文正, 严小天, 刘朝红, 兰红波, 朱晓阳. 基于多材料3D打印的多层柔性及可拉伸电子一体化制造方法及应用研究[J]. 机械工程学报, 2024, 60(21): 275-291.
[2]	赵志斌, 王晨希, 张兴武, 陈雪峰, 李应红. 激光粉末床熔融增材制造过程智能监控研究进展与挑战[J]. 机械工程学报, 2023, 59(19): 253-276.
[3]	黄进, 温翊, 李素兰, 胡文金, 姜渝, 李又兵, 杨朝龙, 瞿伦君, 夏天. 超声波辅助热压成型的聚丙烯/铝合金界面微-纳互锁结构与性能研究[J]. 机械工程学报, 2022, 58(16): 215-223.
[4]	贺佩, 霍子瑶, 贺健康, 冯帆, 朱子才, 李涤尘. 多材料打印仿生离子凝胶电池研究[J]. 机械工程学报, 2021, 57(5): 196-204.
[5]	朱本亮, 张宪民, 李海, 王日鑫, 刘敏, 李昊. 基于节点密度插值的多材料柔顺机构拓扑优化[J]. 机械工程学报, 2021, 57(15): 53-61.
[6]	杜义贤, 李涵钊, 谢黄海, 田启华, 周祥曼, 罗震. 基于序列插值模型和多重网格方法的多材料柔性机构拓扑优化[J]. 机械工程学报, 2018, 54(13): 47-56.
[7]	李永兵, 马运五, 楼铭, 雷海洋, 林忠钦. 轻量化多材料汽车车身连接技术进展^*[J]. 机械工程学报, 2016, 52(24): 1-23.
[8]	张宪民, 胡凯, 王念峰, 张斌. 基于并行策略的多材料柔顺机构多目标拓扑优化^*[J]. 机械工程学报, 2016, 52(19): 1-8.
[9]	张屹;徐磊;刘西霞;李庆福. 高强镀锌钢激光填粉焊接的粉末输送研究[J]. , 2014, 50(4): 60-69.
[10]	张争艳;王小平;胡吉全;陈定方;陶孟仑. 快速成形领域的多材料零件表示算法[J]. , 2013, 49(3): 163-173.
[11]	李永兵;李亚庭;楼铭;林忠钦. 轿车车身轻量化及其对连接技术的挑战[J]. , 2012, 48(18): 44-54.