脂润滑点接触副混合润滑模型研究

doi:10.3901/JME.2022.01.145

机械工程学报 ›› 2022, Vol. 58 ›› Issue (1): 145-153.doi: 10.3901/JME.2022.01.145

扫码分享

脂润滑点接触副混合润滑模型研究

吴正海¹, 徐颖强¹, 刘楷安¹, 陈智勇^1,2

1. 西北工业大学机电学院西安 710072;
2. 洛阳理工学院机械工程学院洛阳 471023

收稿日期:2021-01-21 修回日期:2021-06-18 出版日期:2022-01-05 发布日期:2022-03-19
通讯作者: 徐颖强(通信作者),男,1961年出生,博士,教授,博士研究生导师。主要研究方向为粗糙表面微接触理论、轴承摩擦学理论、热障涂层技术。E-mail:xuyngqng@nwpu.edu.cn
作者简介:吴正海,男,1990年出生,博士研究生。主要研究方向为滚动轴承摩擦学理论。E-mail:wzhawt@163.com
基金资助:
国家自然科学基金（51675427）和河南省科技攻关（192102210026）资助项目。

The Study on Grease Mixed-Lubrication Model of Point Contact Pair

WU Zhenghai¹, XU Yingqiang¹, LIU Kaian¹, CHEN Zhiyong^1,2

1. School of Mechanical and Electrical Engineering, Northwestern Polytechnical University, Xi'an 710072;
2. School of Mechanical Engineering, Luoyang Institute of Science and Technology, Luoyang 471023

Received:2021-01-21 Revised:2021-06-18 Online:2022-01-05 Published:2022-03-19

摘要/Abstract

摘要： 考虑润滑脂非牛顿特性和粗糙表面微凸体接触几何，基于润滑脂Herschel-Bulkey流变模型和微凸体K-E弹塑性接触模型，确定了润滑介质弹流作用和微凸体接触作用的并行处理方案，并提出了一种流体动压区和微凸体接触区的压力边界条件假设，建立了脂润滑点接触副混合润滑的确定性模型。结合处理边界条件的虚压力替代法，构建了混合润滑模型的直接迭代法，研究了不同润滑脂和粗糙表面形貌特征下的点接触副混合润滑特征。结果表明，受表面粗糙形貌影响，二次压力峰和颈缩特征不再明显，脂膜压力分布出现多个压力峰值，且峰值随速度的减小和粗糙度的增大而增大。脂膜厚度与润滑脂稠度等级之间不存在单调关系。当膜厚比约小于4时摩擦副进入混合润滑状态。粗糙表面的偏态对混合润滑存在一定的影响。

关键词: 润滑脂, 点接触, 混合润滑, 粗糙表面, 粗糙度

Abstract: Considering the non-Newtonian characteristics of the grease and the asperity geometry of the rough surface, and based on the Herschel-Bulkey rheological model and the K-E elastoplastic contact model, the parallel processing of the hydrodynamic action of the lubricant and the asperity contact was determined. Combined with the proposed assumption of the boundary condition between the elastodynamic contact zone and the asperity contact zone, a deterministic model of grease mixed-lubrication of the point contact is established. The iterative method of the mixed-lubrication model is constructed by combining the virtual pressure substitution method used to deal with the boundary condition, and then lubrication characteristics under different greases and rough surfaces are studied. The results show that the secondary pressure peak and the necking feature are no longer obvious due to the surface roughness, and multiple pressure peaks appear in the lubrication area, and the pressure peak increases with decreasing speed and increasing roughness. There is no monotonic relationship between the film thickness and the grease consistency grade. When the film thickness ratio is less than about 4, the contact enters the mixed-lubrication state. The skewness of the rough surface has a certain effect on the mixed-lubrication.

Key words: grease, point contact, mixed-lubrication, rough surface, roughness

中图分类号:

TG156

吴正海, 徐颖强, 刘楷安, 陈智勇. 脂润滑点接触副混合润滑模型研究[J]. 机械工程学报, 2022, 58(1): 145-153.

WU Zhenghai, XU Yingqiang, LIU Kaian, CHEN Zhiyong. The Study on Grease Mixed-Lubrication Model of Point Contact Pair[J]. Journal of Mechanical Engineering, 2022, 58(1): 145-153.

参考文献

[1] REN N. Advanced modeling of mixed lubrication and its mechanical and biomedical applications[D]. Illinois:Northwestern University,2009.
[2] TZENG S T,SAIBEL E. Surface roughness effect on slider bearing lubrication[J]. ASLE Trans,1967,10:334-338.
[3] PATIR N. Effects of surface roughness on partial film lubrication using an average flow model based on numerical simulation[D]. Illinois:Northwestern University,1978.
[4] PATIR N,CHENG H S. Average flow model for determining effects of 3-dimensinal roughness on partial hydrodynamic lubrication[J]. Journal of Lubrication Technology,1978,100(1):12-17.
[5] ELROD H G. A general theory for laminar lubrication with Reynolds roughness[J]. Journal of Lubrication Technology,1979,101(1):8-14.
[6] TRIPP J H. Surface-roughness effects in hydrodynamic lubrication the flow factor method[J]. Journal of Lubrication Technology,1983,105(3):458-465.
[7] PEEKEN H J,KNOLL G,RIENACKER A,et al. On the numerical determination of flow factors[J]. Journal of Tribology,1997,119(2):259-264.
[8] BAYADA G,FAURE J B. A double scale analysis approach of the Reynolds roughness comments and application to the journal bearing[J]. Journal of Tribology,1989,111(2):323-330.
[9] ZHU D,AI X L. Point contact EHL based on optically measured three-dimensional rough surfaces[J]. Journal of Tribology,1997,119(3):375-384.
[10] ZHU D,HU Y Z. The study of transition from full film elastohydrodynamic to mixed and boundary lubrication[J]. Proceedings of the STLE/ASME,1999,150-156.
[11] HU Y Z,ZHU D. A full numerical solution to the mixed lubrication in point contacts[J]. Journal of Tribology,2000,122(1):1-9.
[12] WANG W Z,LIU Y C,WANG H,et al. A computer thermal model of mixed lubrication in point contacts[J]. Journal of Tribology,2004,126(1):162-170.
[13] LI S,KAHRAMAN A. A mixed EHL model with asymmetric integrated control volume discretization[J]. Tribology International,2009,42(8):1163-1172.
[14] AZAM A,DORGHAM A,MORINA A,et al. A simple deterministic plastoelastohydrodynamic lubrication (PEHL) model in mixed lubrication[J]. Tribology International,2018,131(3):520-529.
[15] XIANG C,WANG Z,JIA X,et al. Numerical simulation model of a reciprocating seal based on the mixed-lubrication theory[J]. The Journal of Engineering,2019(13):49-53.
[16] BERGMANN P,GRÜN F,GÓDOR I, et al. On the modelling of mixed lubrication of conformal contacts[J]. Tribology International,2018,125(9):220-236.
[17] YANG J,WANG D,WEI P,et al. A mixed EHL model of grease lubrication considering surface roughness and the study of friction behavior[J]. Tribology International,2021,154(2):106710.
[18] EDER S J,IELCHICI C,KRENN S,et al. An experimental framework for determining wear in porous journal bearings operated in the mixed lubrication regime[J]. Tribology International,2018,123(7):1-9.
[19] HERSCHEL W H,BULKLEY R. Measurement of consistency as applied to rubber-benzene solutions[J]. Proceeding of American Society of Testing Material,1926,26(2):621-633.
[20] ROELANDS C J A,VLUGTER J C,WATERMAN H I. The viscosity-temperature-pressure relationship of lubricating oils and its correlation with chemical constitution[J]. Journal of Fluids Engineering,1963,85(4):601-607.
[21] DOWSON D,HIGGINSON G R. Elasto-hydrodynaminc lubrication[M]. Oxfrod:Pergamon Press,1977.
[22] 温诗铸,黄平,田煜,等. 摩擦学原理[M]. 第五版. 北京:清华大学出版社,2018. WEN S Z,HUANG P,TIAN Y,et al. Principles of Tribology[M]. 5th Edition. Beijing:Tsinghua University Press,2018.
[23] 张鹏顺,陆思聪. 弹性流体动力润滑及其应用[M]. 北京:高等教育出版社,1995. ZHANG Pengshun, LU Sicong. Elastohydrodynamic lubrication and its application[M]. Beijing:Higher Education Press, 1995.
[24] XU Y. An analysis of elastic rough contact models[D]. Auburn:Auburn University,2012.
[25] KOGUT L,ETSION I. Elastic-plastic contact analysis of a sphere and a rigid flat[J]. Journal of Applied Mechanics,2002,69(5):657-662.
[26] ETSION I,KLIGERMAN Y,KADIN Y. Unloading of an elastic-plastic loaded spherical contact[J]. International Journal of Solids and Structures,2005,42(13):3716-3729.
[27] LIU S,WANG Q,LIU G. A versatile method of discrete convolution and FFT (DC-FFT) for contact analyses[J]. Wear,2000,243(1-2):101-111.
[28] HU Y Z,TONDER K. Simulation of 3-D random rough surface by 2-D digital filter and Fourier analysis[J]. International Journal of Machine Tools & Manufacture,1992,32(1):83-90.
[29] ZHU D. On some aspects of numerical solutions of thin-film and mixed elastohydrodynamic lubrication[J]. Proceedings of the Institution of Mechanical Engineers Part J-Journal of Engineering Tribology,2007,221(J5):561-579.
[30] KAUZLARICH J,GREENWOOD J A. Elasto- hydrodynamic lubrication with Herschel-Bulkley model greases[J]. ASLE Transactions,1972,15(4):269-277.
[31] YOO J G,KIM K W. Numerical analysis of grease thermal elastohydrodynamic lubrication problems using the Herschel-Bulkley model[J]. Tribology International,1997,30(6):401-408.
[32] LUGT P M. A review on grease lubrication in rolling bearings[J]. Tribology Transactions,2009,52(4):470-480.

脂润滑点接触副混合润滑模型研究

The Study on Grease Mixed-Lubrication Model of Point Contact Pair

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘鑫, 张俊, 徐斌斌, 刘弘光, 赵万华. 激光辅助铣削过程的预热温度场调控方法研究[J]. 机械工程学报, 2024, 60(9): 218-228.
[2]	陈守安, 肖科, 程功, 韩彦峰. 混合润滑下考虑表面形貌的齿面摩擦与接触特性[J]. 机械工程学报, 2024, 60(7): 184-194.
[3]	朱少禹, 张向军, 孙军, 王大刚. 粗糙表面轴承微极流体润滑的平均流量模型[J]. 机械工程学报, 2024, 60(7): 203-211.
[4]	方从富, 李弘扬, 沈剑云, 吴贤. 融合磨粒特征和工艺参数的粗糙度智能预测研究[J]. 机械工程学报, 2024, 60(7): 224-235.
[5]	纪佳馨, 彭程, 项冲, 黄乐, 郭飞. 考虑变速条件的斯特封磨损寿命预测方法[J]. 机械工程学报, 2024, 60(3): 191-202.
[6]	何春雷, 王姝淇, 李东洋, 耿昆, 陈光, 任成祖. 晶粒对多晶材料超精密切削影响的研究进展[J]. 机械工程学报, 2024, 60(3): 373-392.
[7]	马泳涛, 孙宁, 王俊龙, 李春凡, 卢春生, 张彬, 刘兰荣. 前混合水射流喷丸覆盖率计算及对渗碳钢表面完整性的影响研究[J]. 机械工程学报, 2024, 60(3): 393-404.
[8]	温雪龙, 赵正豪, 巩亚东, 李俊鹏. FeCoNiCrAl_x高熵合金铣削表面质量影响因素实验研究[J]. 机械工程学报, 2024, 60(17): 367-378.
[9]	朱鹏娟, 刘晓玲, 周亚林, 何文卓, 郭峰. 混合陶瓷球轴承的热混合润滑性能分析[J]. 机械工程学报, 2024, 60(15): 205-215.
[10]	党嘉强, 安庆龙, 李宇罡, 明伟伟, 王浩伟, 陈明. 300M钢超声滚压表面形貌演变机理和试验表征[J]. 机械工程学报, 2024, 60(15): 358-367.
[11]	张园, 徐念伟, 鲍岩, 董志刚, 韩松, 郭东明, 康仁科. 轴向超声辅助端面磨削金属表面形貌及粗糙度预测[J]. 机械工程学报, 2023, 59(5): 307-316.
[12]	王钦, 贺迪, 桂良进, 范子杰. 考虑系统变形的电驱动桥齿轮啮合效率研究[J]. 机械工程学报, 2023, 59(3): 66-75.
[13]	何春雷, 张建国, 王姝淇, 任成祖. 基于多波长散射光特性的铝合金超精密车削表面粗糙度测量方法研究[J]. 机械工程学报, 2023, 59(3): 308-317.
[14]	张瑜, 康仁科, 高尚, 黄金星, 朱祥龙. 湿式机械化学磨削单晶硅的软磨料砂轮及其磨削性能[J]. 机械工程学报, 2023, 59(3): 328-336.
[15]	郭江, 杨哲, 张鹏飞, 李琳光, 俞学雯, 潘博. FeCrAl合金化学机械抛光粗糙度预测模型研究[J]. 机械工程学报, 2023, 59(23): 310-319.