铝合金微型热管分流挤压模具变形分析与优化研究

doi:10.3901/JME.2023.22.265

机械工程学报 ›› 2023, Vol. 59 ›› Issue (22): 265-274.doi: 10.3901/JME.2023.22.265

扫码分享

铝合金微型热管分流挤压模具变形分析与优化研究

刘勇达^1,2, 徐杰^1,2, 单德彬^1,2, 郭斌^1,2

1. 哈尔滨工业大学微系统与微结构制造教育部重点实验室哈尔滨 150080;
2. 哈尔滨工业大学材料科学与工程学院哈尔滨 150001

收稿日期:2022-12-28 修回日期:2023-05-21 出版日期:2023-11-20 发布日期:2024-02-19
通讯作者: 徐杰(通信作者)，男，1980年出生，博士，教授，博士研究生导师。主要研究方向为微纳成形理论与工艺。E-mail：xjhit@hit.edu.cn
作者简介:刘勇达，男，1991年出生，博士研究生。主要研究方向为轻质热管微纳制造及应用。E-mail：13s009128@hit.edu.cn
基金资助:
国家自然科学基金(51635005)和111工程(B18017)资助项目。

Tool Deflection Analysis and Optimization of Porthole Die for Micro Heat Pipe in Aluminum Alloy

LIU Yongda^1,2, XU Jie^1,2, SHAN Debin^1,2, GUO Bin^1,2

1. Key Laboratory of Micro-Systems and Micro-Structures Manufacturing of Ministry of Education, Harbin Institute of Technology, Harbin 150080;
2. School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001

Received:2022-12-28 Revised:2023-05-21 Online:2023-11-20 Published:2024-02-19

摘要/Abstract

摘要： 研究铝合金微型热管这类微型复杂空心挤压型材极易产生内腔偏心缺陷的问题，提出相应的挤压模具的结构设计原则。基于Altair Inspire Extrude Metal有限元分析软件，分析挤压比、焊合室高度、模芯间距和工作带长度对模芯变形的影响规律。模拟结果表明，焊合室高度和模芯间距对模芯变形的影响比较显著，而挤压比和工作带长度影响微弱。当焊合室高度提高至某一阈值时，模芯的最大变形量随着焊合室高度增加。模芯间距存在最优值，偏离该值会促进模芯变形。挤压试验结果表明，在较优的模具结构参数下获得壁厚尺寸精度±0.04 mm的微型热管型材，对应的主要模具结构参数为挤压比137、模芯间距28 mm、焊合室高度8 mm和工作带长度3 mm。

关键词: 微型热管, 分流模具, 模具优化, 铝合金

Abstract: The problem of cavity eccentricity of micro complex hollow extruded profiles such as micro heat pipes in aluminum alloy is investigated, and the corresponding principle of structural design in porthole die is proposed. The influences of extrusion ratio, welding chamber height, die core spacing and bearing length on the die core deflection are analyzed using Altair Inspire Extrude Metal finite element analysis software. The simulation results show that the influences of welding chamber height and die core spacing are significantly evident, whereas the influences of extrusion ratio and bearing length are weak. The maximum deformation of the die core increases with welding chamber height when it increases to a certain threshold. There is an optimum value for die core spacing, deviations from this value would promote die core deformation. The experimental results show that the micro heat pipe profile with a wall thickness dimensional accuracy of ±0.04 mm is obtained under the better die structure parameters. The corresponding main die structure parameters are extrusion ratio of 137, die core spacing of 28 mm, welding chamber height of 8 mm and bearing length of 3 mm.

Key words: micro heat pipe, porthole die, die optimization, aluminum alloy

中图分类号:

TG376

刘勇达, 徐杰, 单德彬, 郭斌. 铝合金微型热管分流挤压模具变形分析与优化研究[J]. 机械工程学报, 2023, 59(22): 265-274.

LIU Yongda, XU Jie, SHAN Debin, GUO Bin. Tool Deflection Analysis and Optimization of Porthole Die for Micro Heat Pipe in Aluminum Alloy[J]. Journal of Mechanical Engineering, 2023, 59(22): 265-274.

参考文献

[1] 苗建印,李亭寒,杨沪宁,等. 微小型热管的研制及应用[C]//第十届全国热管会议论文集. 贵阳:中国工程热物理学会, 2006:137-142. MIAO Jianyin, LI Tinghan, YANG Huning, et al. Development and application of micro heat pipe[C]//Proceedings of 10th Conference on Heat Pipes. Guiyang:Chinese Society of Engineering Thermophysics, 2006:137-142.
[2] GEIGER M, KLEINER M, ECKSTEIN R, et al. Microforming[J]. CIRP Annals-Manufacturing Technology, 2001, 50(2):445-462.
[3] XU J, WANG X W, WANG C J, et al. A review on micro/nanoforming to fabricate 3D metallic structures[J]. Advanced Materials, 2020, 33(6):2000893.
[4] YU J Q, ZHAO G Q, CHEN L. Analysis of longitudinal weld seam defects and investigation of solid-state bonding criteria in porthole die extrusion process of aluminum alloy profiles[J]. Journal of Materials Processing Technology, 2016, 237:31-47.
[5] YU J Q, ZHAO G Q, CUI W C, et al. Evaluating the welding quality of longitudinal welds in a hollow profile manufactured by porthole die extrusion:Experiments and simulation[J]. Journal of Manufacturing Processes, 2019, 38:502-515.
[6] HOA C, DEMOLDER B, ALEXANDRE A. Roadmap for developing heat pipes for ALCATEL SPACE's satellites[J]. Applied Thermal Engineering, 2003, 23(9):1099-1108.
[7] 孙晓龙,沈健,闫晓东,等. Ω槽道翅片管挤压过程数值模拟及模具优化[J]. 锻压技术, 2014, 39(9):58-62. SUN Xiaolong, SHEN Jian, YAN Xiaodong, et al. Numerical simulation of extrusion process and optimization of die structure for Ω grooved finned-tube[J]. Forging & Stamping Technology, 2014, 39(9):58-62.
[8] 朱圆斌,李仪龙,曹震波,等. 厚壁"Ω"形微槽道铝热管的连续挤压研究[J]. 热加工工艺, 2013, 42(19):85-87, 91. ZHU Yuanbin, LI Yilong, CAO Zhenbo, et al. Study on continuous extrusion of aluminum heat pipe with thick-walled "Ω" shaped micro-grooves[J]. Hot Working Technology, 2013, 42(19):85-87, 91.
[9] LIU Y D, XU J, ZHANG Z W, et al. Micro-extrusion process and microstructure evolution of miniature heat pipe in 6063 aluminum alloy[J]. The International Journal of Advanced Manufacturing Technology, 2022, 120:6463-6480.
[10] LIU Y D, WANG X L, XU J, et al. Formation mechanism and optimization strategy of surface back-end defects in miniature complex hollow extruded profile[J]. Journal of Materials Processing Technology, 2022, 308:117726.
[11] 谢建新, 刘静安. 金属挤压理论与技术[M]. 2版. 北京:冶金工业出版社, 2012. XIE Jianxin, LIU Jingan. Theory and technology of metals extrusion[M]. 2nd ed. Beijing:Metallurgical Industry Press, 2012.
[12] ENGELHARDT M, KURMAJEV S, MAIER J, et al. The application of FEA for optimization of die design[J]. Materials Today:Proceedings, 2019, 10:226-233.
[13] HE Z, WANG H N, WANG M J, et al. Simulation of extrusion process of complicated aluminum profile and die trial[J]. Transactions of Nonferrous Metals Society of China, 2012, 22(7):1732-1737.
[14] SUN Y D, CHEN Q R, SUN W J. Numerical simulation of extrusion process and die structure optimization for a complex magnesium doorframe[J]. International Journal of Advanced Manufacturing Technology, 2015, 80:495-506.
[15] YI J, WANG Z H, LIU Z W, et al. FE analysis of extrusion defect and optimization of metal flow in porthole die for complex hollow aluminium profile[J]. Transactions of Nonferrous Metals Society of China, 2018, 28(10):2094-2101.
[16] DING S Y, JIN S. Microbulging extrusion of aluminum alloy to fabricate micro/meso features for heat pipes[J]. The International Journal of Advanced Manufacturing Technology, 2016, 86(9-12):2975-2987.

铝合金微型热管分流挤压模具变形分析与优化研究

Tool Deflection Analysis and Optimization of Porthole Die for Micro Heat Pipe in Aluminum Alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李力, 王一轩, 罗芬, 张文涛, 赵巍, 李小强. 钎焊时间对TiH₂-65Ni+TiB₂钎料钎焊连接TiAl合金接头的影响[J]. 机械工程学报, 2024, 60(8): 176-185.
[2]	张婷婷, 许振波, 王艳, 卞功波, 王涛, 王文先. 高频脉冲电流辅助镁/铝合金一步轧焊复合板制备及界面接合机理[J]. 机械工程学报, 2024, 60(4): 305-315.
[3]	林智雄, 邵震, 梁鑫裕, 崔雷, 王东坡, 谢燕, 黄一鸣, 杨立军. 2219铝合金拉拔式摩擦塞补焊成形过程分析[J]. 机械工程学报, 2024, 60(20): 144-152.
[4]	吴洁, 沈以赴, 黄国强. 2024铝合金填丝TIG焊接头搅拌摩擦加工组织和性能研究[J]. 机械工程学报, 2024, 60(20): 153-161.
[5]	王刚, 谷诤巍, 于歌, 李欣. 热成形工艺条件下7075-H18铝合金板材塑性流动行为的本构建模[J]. 机械工程学报, 2024, 60(2): 188-196.
[6]	王相宇, 仇文豪, 牛金涛, 刘国梁, 付秀丽, 郭培全, 乔阳. 钛铝合金低温切削加工温度的实验和仿真研究[J]. 机械工程学报, 2024, 60(19): 318-331.
[7]	王瑞林, 杨新岐, 唐文珅, 罗庭. AA2024-T3铝合金搅拌摩擦沉积增材组织及性能[J]. 机械工程学报, 2024, 60(18): 146-153.
[8]	张会杰, 孔旭亮, 姚恩泽, 马康, 宋建岭. 母材相对位置对航天异种高强铝合金FSW接头组织性能的影响机理[J]. 机械工程学报, 2024, 60(18): 154-162.
[9]	程吉, 曹宏东, 屈蜀光, 郑凯伦, 何祝斌. 基于黏塑性本构的6061铝合金管热气胀成形工艺参量建模研究[J]. 机械工程学报, 2024, 60(16): 108-117.
[10]	杨夏炜, 孟廷曦, 褚强, 范文龙, 苏宇, 马铁军, 李文亚. 铝合金双面搅拌摩擦焊接的研究进展[J]. 机械工程学报, 2024, 60(14): 77-96.
[11]	王浩, 刘坤, 李洁, 余文明, 吴红, OKULOV Artem. 铝合金焊接凝固裂纹及焊材抗裂性的研究进展[J]. 机械工程学报, 2024, 60(12): 207-219.
[12]	陈睿, 程诗敏, 温仕成, 赵子衡, 彭锐涛, 胡聪芳, 肖湘武. 基于J-C模型修正的7150-T6航空铝合金薄壁开孔圆管结构优化[J]. 机械工程学报, 2024, 60(11): 95-104.
[13]	高转妮, 王磊磊, 李响, 刘志强, 吕飞阅, 黎一帆, 占小红. 7075铝合金激光熔丝增材制造热循环和温度梯度对熔池凝固组织的影响研究[J]. 机械工程学报, 2024, 60(1): 96-118.
[14]	陈宇, 刘文文, 王涛, 申宏卓, 陈科, 张斌. 预制波纹工艺对钢/铝/铝合金复合板界面影响机制研究[J]. 机械工程学报, 2023, 59(8): 74-82.
[15]	周丹, 王鹏程, 张腾飞, 宋守许. ZL101A合金TIG修复色差及组织性能间的相关性研究[J]. 机械工程学报, 2023, 59(7): 398-406.