异性分形表面合成方法及表面特性研究

doi:10.3901/JME.2019.21.118

机械工程学报 ›› 2019, Vol. 55 ›› Issue (21): 118-126.doi: 10.3901/JME.2019.21.118

扫码分享

异性分形表面合成方法及表面特性研究

张玲, 郑国磊, 杨荣荣

北京航空航天大学机械工程及自动化学院北京 100191

收稿日期:2019-01-23 修回日期:2019-06-09 出版日期:2019-11-05 发布日期:2020-01-08
通讯作者: 郑国磊(通信作者),男,1964年出生,博士,教授,博士研究生导师。主要研究方向为数字化制造,增材制造及数字化建模技术。E-mail:zhengguolei@buaa.edu.cn
作者简介:张玲,女,1981年出生,讲师,博士研究生。主要研究方向为数字化建模仿真。E-mail:zhling4849@126.com;杨荣荣,男,1981年出生,博士。主要研究方向为数控技术及电液伺服控制。E-mail:yr13236@163.com

Study of Synthesis and Properties of Anisotropic Fractal Surfaces

ZHANG Ling, ZHENG Guolei, YANG Rongrong

School of Mechanical Engineering and Automation, Beihang University, Beijing 100191

Received:2019-01-23 Revised:2019-06-09 Online:2019-11-05 Published:2020-01-08

摘要/Abstract

摘要： 针对异性分形表面的建模，提出了一种以二维离散傅里叶变换为基础，以名义维数D_x，D_y为驱动参数的表面合成方法——合成维数法。通过对比名义维数与采用轮廓功率谱公式和数值分析法得到的表面计算维数的关系，验证了该方法的有效性。探讨了名义维数对x，y方向轮廓能量分布以及对表面及轮廓粗糙度的影响。一方面在轮廓功率谱分析的基础上定义了轮廓累计功率比，用于描述表面轮廓的能量分布特性，不仅促进了对名义维数和轮廓能量关系的定性理解，更能定量地解释不同维数值影响下频率和轮廓能量分布的关系。另一方面以能量分析为切入点，建立了名义维数与表面及轮廓粗糙度参数间的联系，并且依据能量守恒定律，证明并揭示了轮廓粗糙度R_qx，R_qy之间以及二者与面粗糙度S_q的关系。同时得出结论，D_x或D_y值越小，低频部分能量占比越高，反之亦然，但是x，y方向轮廓总功率始终相等，并随D_x，D_y增大而增大；D_x，D_y只影响S_q，R_qx，R_qy的绝对数值，二者的增大会引起粗糙度值增加，但并不影响R_qx，R_qy的相对关系。

关键词: 分形表面, 离散傅里叶变换, 合成维数法, 名义维数, 轮廓能量分布, 粗糙度

Abstract: For modeling of anisotropic fractal surfaces, a novel synthesis method named by synthetic dimension method is proposed, which is based on discrete Fourier transform and aroused by the nominal dimension D_x,D_y. By contrasting nominal dimension with computed dimension values that are obtained by the derived power spectrum formula of surface's profiles and the concomitant numerical calculation, the method proves to be useful. Further, relationships between nominal dimensions with power distribution and roughness of the generated fractal surface and surface profiles in x, y direction are discussed. On the one hand, through analyzing of surface's profile power spectrum, profile's cumulative power ratio is introduced to describe power distribution, by which the qualitative understanding of effects of nominal dimensions on profile's power can be promoted, and the relation between profile's frequency with power distribution under the impact of the dimensions is also explained quantitatively. On the other hand, taking energy analysis as an entrance, connections of nominal dimensions with surface and profile roughness are established. Meanwhile, according to the conservation of energy principle, relationships of the profile roughness R_qx,R_qy and the surface roughness S_q are revealed. The results show that smaller D_x or D_y induces a higher low-frequency energy ratio in corresponding direction, and vice versa, however, the total profile's powers in x and y direction always equal, and increase with D_x and D_y. In addition, D_x, D_y only affect the absolute roughness values of S_q,R_qx and R_qy by causing roughness increase with them, not the relative relation of R_qx and R_qy.

Key words: fractal surface, discrete Fourier transform, synthetic dimension method, nominal dimension, profile's power distribution, roughness

中图分类号:

TH161

张玲, 郑国磊, 杨荣荣. 异性分形表面合成方法及表面特性研究[J]. 机械工程学报, 2019, 55(21): 118-126.

ZHANG Ling, ZHENG Guolei, YANG Rongrong. Study of Synthesis and Properties of Anisotropic Fractal Surfaces[J]. Journal of Mechanical Engineering, 2019, 55(21): 118-126.

参考文献

[1] 梁志强,黄迪青,周天丰,等. 螺旋伞齿轮磨削表面形貌仿真与试验研究[J]. 机械工程学报,2019,55(3):204-211. LIANG Zhiqiang,HUANG Diqing,ZHOU Tianfeng,et al. Simulation and experimental research on grinding surface topography of spiral bevel gear[J]. Journal of Mechanical Engineering,2019,55(3):204-211.
[2] 秦红玲,郭建义,徐翔,等. 滑动轴承表面形貌的分形模拟及对摩擦学性能的影响[J]. 润滑与密封,2018,43(2):47-52. QIN Hongling,GUO Jianyi,XU Xiang,et al. On fractal modeling and tribological properties of surface morphology for sliding bearing[J]. Lubrication Engineering,2018,43(2):47-52.
[3] HU Songtao,HUANG Weifeng,BRUNETIERE N,et al. Stratified effect of continuous bi-Gaussian rough surface on lubrication and asperity contact[J]. Tribology International,2016,104:328-341.
[4] THOMAS A P,THOMAS T R. Engineering surface as fractals,fractal aspects of materials[M]. Pittsburgh:Materials Research Society,1986.
[5] 周超,高诚辉. 基于离散傅里叶变换的分形粗糙表面轮廓合成与研究[J]. 机械工程学报,2011,47(17):99-103. ZHOU Chao,GAO Chenghui. Study of synthesized fractal surface's profiles based on discrete Fourier transform[J]. Journal of Mechanical Engineering,2011,47(17):99-103.
[6] 陈辉,胡元中,王慧,等. 粗糙表面分形特征的模拟及其表征[J]. 机械工程学报,2006,42(9):219-223. CHEN Hui,HU Yuanzhong,WANG Hui,et al. Simulation and characterization of fractal rough surfaces[J].Chinese Journal of Mechanical Engineering,2006,42(9):219-223.
[7] 淦犇,黄宜坚. 铣削加工表面轮廓的几何分形特征[J].华侨大学学报,2010,31(4):371-377. GAN Ben,HUANG Yijian. Geometry fractal characteristics of milled surface profiles[J]. Journal of Huaqiao University,2010,31(4):371-377.
[8] THOMAS T R,ROSEN B G,AMINI N. Fractal characterization of the anisotropy of rough surfaces[J]. Wear,1999,232(1):41-50.
[9] LI Chengui,DONG Shen,ZHANG Guoxiong. Evaluation of the anisotropy of machined 3D surface topography[J]. Wear,2000,237(2):211-216.
[10] WU Jiunnjong. Analyses and simulation of anisotropic fractal surfaces[J]. Chaos Solitons & Fractals,2002,13(9):1791-1806.
[11] 黄祥,王清辉,李伟晨,等. 各向异性表面生成算法及其应用[J]. 华南理工大学学报,2013,41(7):1-6. HUANG Xiang,WANG Qinghui,LI Weichen,et al. Generation algorithm of anisotropic surface and its application[J]. Journal of South China University of Techonology,2013,41(7):1-6.
[12] 赵歆波,PETROU M,张定华,等. 基于频谱合成的自然地形生成方法[J]. 机械科学与技术,2004,23(3):263-265. ZHAO Xinbo,PETROU M,ZHANG Dinghua,et al. A method for generating natural terrain based on spectral synthesis[J]. Mechanical Science and Technology for Aerospace Engineering,2004,23(3):263-265.
[13] 周超,黄健萌,高诚辉. 各向异性分形表面建模研究[J]. 中国机械工程,2015,26(8):1019-1023. ZHOU Chao,HUANG Jianmeng,GAO Chenghui. Modeling of anisotropic fractal surface[J]. Journal of China Mechanical Engineering,2015,26(8):1019-1023.
[14] PEITGEN H O,SAUPE D. The science of fractal images[M]. Berlin:Springer-Verlag,1988.
[15] REED I S,LEE P K,TRUONG T K. Spectral representation of fractional Brownian motion in n dimensions and its properties[J]. IEEE Transactions on Information Theory,1995,41(5):1439-1451.
[16] KULESZA S,BRAMOWICA M. A comparative study of correlation methods for determination of fractal parameters in surface characterization[J]. Applied Surface Science,2014,293(8):196-201.
[17] 王余松,张学良,温淑花,等. 分形粗糙表面特征长度尺度参数小波识别法[J]. 机械工程学报,2018,54(5):185-192. WANG Yusong,ZHANG Xueliang,WEN Shuhua,et al. Wavelet method identifying the characteristic length scale parameter of fractal rough surface[J]. Journal of Mechanical Engineering,2018,54(5):185-192.
[18] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会. GB/T 33523.2-2017产品几何技术规范(GPS)表面结构区域法-第2部分:术语、定义及表面结构参数[S]. 北京:中国标准出版社,2017. General Administration of Quality Supervision,Inspection and Quarantine of the People's Republic of China,Standardization Administration of the People's Republic of China. GB/T 33523.2-2017 Geometrical product specifications (GPS)-Surface texture:Areal-Part 2:Terms,definitions and surface texture parameters[S]. Beijing:China Press Standards,2017.
[19] OPPENHEIM A V,SCHAFER R W. Discrete-time signal processing[M]. 3rd ed. Englewood Cliffs:Prentice Hall,2009.

异性分形表面合成方法及表面特性研究

Study of Synthesis and Properties of Anisotropic Fractal Surfaces

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘鑫, 张俊, 徐斌斌, 刘弘光, 赵万华. 激光辅助铣削过程的预热温度场调控方法研究[J]. 机械工程学报, 2024, 60(9): 218-228.
[2]	朱少禹, 张向军, 孙军, 王大刚. 粗糙表面轴承微极流体润滑的平均流量模型[J]. 机械工程学报, 2024, 60(7): 203-211.
[3]	方从富, 李弘扬, 沈剑云, 吴贤. 融合磨粒特征和工艺参数的粗糙度智能预测研究[J]. 机械工程学报, 2024, 60(7): 224-235.
[4]	何春雷, 王姝淇, 李东洋, 耿昆, 陈光, 任成祖. 晶粒对多晶材料超精密切削影响的研究进展[J]. 机械工程学报, 2024, 60(3): 373-392.
[5]	马泳涛, 孙宁, 王俊龙, 李春凡, 卢春生, 张彬, 刘兰荣. 前混合水射流喷丸覆盖率计算及对渗碳钢表面完整性的影响研究[J]. 机械工程学报, 2024, 60(3): 393-404.
[6]	温雪龙, 赵正豪, 巩亚东, 李俊鹏. FeCoNiCrAl_x高熵合金铣削表面质量影响因素实验研究[J]. 机械工程学报, 2024, 60(17): 367-378.
[7]	党嘉强, 安庆龙, 李宇罡, 明伟伟, 王浩伟, 陈明. 300M钢超声滚压表面形貌演变机理和试验表征[J]. 机械工程学报, 2024, 60(15): 358-367.
[8]	张园, 徐念伟, 鲍岩, 董志刚, 韩松, 郭东明, 康仁科. 轴向超声辅助端面磨削金属表面形貌及粗糙度预测[J]. 机械工程学报, 2023, 59(5): 307-316.
[9]	何春雷, 张建国, 王姝淇, 任成祖. 基于多波长散射光特性的铝合金超精密车削表面粗糙度测量方法研究[J]. 机械工程学报, 2023, 59(3): 308-317.
[10]	张瑜, 康仁科, 高尚, 黄金星, 朱祥龙. 湿式机械化学磨削单晶硅的软磨料砂轮及其磨削性能[J]. 机械工程学报, 2023, 59(3): 328-336.
[11]	郭江, 杨哲, 张鹏飞, 李琳光, 俞学雯, 潘博. FeCrAl合金化学机械抛光粗糙度预测模型研究[J]. 机械工程学报, 2023, 59(23): 310-319.
[12]	冯彦, 邱卓一, 史修江, 卢熙群, 孙文, 华德良, 孙焕. 考虑真实粗糙表面的燃机球轴承磨损与混合润滑耦合机理[J]. 机械工程学报, 2023, 59(21): 330-340.
[13]	周炜, 赵岱岩, 唐进元. 一种基于峰谷数据映射的粗糙度轮廓重构方法[J]. 机械工程学报, 2023, 59(17): 268-278.
[14]	郭国强, 杨博宇, 李建华, 成群林, 王大中, 林立芳, 沈彬. 基于切削运动学分析的铣削加工表面粗糙度预测方法研究[J]. 机械工程学报, 2023, 59(13): 314-324.
[15]	滕洪钊, 邓朝晖, 吕黎曙, 谷倩微, 刘涛, 卓荣锦. 多传感器信息融合的加工过程状态监测研究[J]. 机械工程学报, 2022, 58(6): 26-41.