• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (18): 311-320.doi: 10.3901/JME.260222

• 材料科学与工程 • 上一篇    

扫码分享

微波加热再制造Inconel 718合金涂层微观组织与耐磨性能研究

钱正春1,2, 张恒玮1, 徐鸿蒙1, 成焕波1, 丁文政1   

  1. 1. 南京工程学院机械工程学院 南京 211167;
    2. 合肥工业大学机电产品低碳循环利用技术与装备安徽省重点实验室 合肥 230009
  • 收稿日期:2025-10-30 修回日期:2026-05-12 发布日期:2026-11-20
  • 作者简介:钱正春(通信作者),男,1992年出生,博士,副教授,硕士研究生导师。主要研究方向为再制造。E-mail:qianzhengchun@njit.edu.cn
  • 基金资助:
    国家自然科学基金(52005246)、江苏省自然科学基金(BK20241964)、江苏省高校自然科学研究重大项目(25KJA460006)、中央高校基本科研业务费专项资金(PA2024GDSK0069)和江苏省高校“青蓝工程”资助项目。

Study on Microstructure and Wear Resistance of Inconel 718 Alloy Coating Remanufactured by Microwave Heating

QIAN Zhengchun1,2, ZHANG Hengwei1, XU Hongmeng1, CHENG Huanbo1, DING Wenzheng1   

  1. 1. Nanjing Institute of Technology, School of Mechanical Engineering, Nanjing 211167;
    2. Anhui Key Laboratory of Low Carbon Recycling Technology and Equipment for Mechanical and Electrical Products, Hefei University of Technology, Hefei 230009
  • Received:2025-10-30 Revised:2026-05-12 Published:2026-11-20

摘要: 目前常见的镍基高温合金涂层再制造技术主要包括激光熔覆、等离子堆焊、热喷涂等,存在修复工艺复杂、设备成本高昂和容易形成热损伤等问题。为此,创新提出一种微波加热再制造(Microwave heating remanufacturing,MHR)技术,并在毛坯坡口处成功制备了Inconel 718镍基高温合金涂层。MHR涂层的微观组织结构呈现梯度分布,其中试样的上层以枝晶为主,出现大量的碳化铬硬质相;中层的粉末经过“微熔-颈缩-液化-填充”四个微波加热阶段形成胞状晶,并伴随有大量准连续网络状的碳化物形成增强骨架;下层基体受热影响作用产生链状Laves相。此外,MHR涂层的显微硬度也呈现梯度分布特点,其中涂层顶部的显微硬度最高,坡口界面附近的显微硬度最低。摩擦磨损实验结果显示,MHR涂层的摩擦因数和磨损质量均较小,耐磨性能提升超过30%;磨痕形貌表明,MHR涂层顶部的枝晶可以承受较大的法向载荷与横向剪切力,压弯后形成的鱼鳞状分层结构还可以继续起到收集磨屑的作用,极大提升了涂层的耐磨性能,证实了MHR技术在修复Inconel 718镍基高温合金中的巨大潜力。

关键词: 镍基高温合金, 再制造, 微波加热, 修复, 耐磨性能

Abstract: At present, the traditional remanufacturing technologies for nickel-based superalloy coatings mainly include laser cladding, plasma surfacing, and thermal spraying. However, they have limitations such as complex repair processes, high equipment costs, and the tendency to cause thermal damage. Therefore, a microwave heating remanufacturing (MHR) technology is innovatively proposed, and the Inconel 718 nickel-based superalloy coating is successfully prepared at the groove of remanufacturing core. The MHR coating shows a gradient distribution, in which the upper layer is dominated by dendrites, and a large number of chromium carbide hard phases appear in this zone. The middle layer of the powders undergoes four microwave heating stages of “micromelting-necking -liquefaction-filling” to form cellular crystals, accompanied by a large number of quasi-continuous network-like Laves phase precipitation as the enhanced skeleton. The lower matrix produces the chain-like Laves phase under the effect of heating. In addition, the microhardness of the MHR coating also shows a gradient distribution. The microhardness at the top of coating is the highest, and near the groove interface is the lowest. The friction and wear experiments show that the friction coefficient and wear weight of MHR coating are small, and the wear resistance is improved by more than 30%. The wear scar morphology shows that the dendrites on the top of MHR coating can withstand large normal load and transverse shear force. Besides, the fish-scale layered structure formed after dendrites bending can play a role of entrapping wear debris, which greatly improves the wear resistance of coating. The research results verify the great potential of MHR technology in repairing Inconel 718 nickel-based superalloy.

Key words: nickel-based superalloy, remanufacturing, microwave heating, repair, wear resistance

中图分类号: