非均匀激光热源焊接铜/钢接头的组织及力学性能研究

doi:10.3901/JME.2025.06.151

机械工程学报 ›› 2025, Vol. 61 ›› Issue (6): 151-159.doi: 10.3901/JME.2025.06.151

• 材料科学与工程 • 上一篇

扫码分享

非均匀激光热源焊接铜/钢接头的组织及力学性能研究

韩静¹, 石玗¹, 李广¹, 张航², 陆刚²

1. 兰州理工大学省部共建有色金属先进加工与再利用国家重点实验室兰州 730050;
2. 浙江巴顿焊接技术研究院杭州 311200

收稿日期:2024-04-17 修回日期:2024-12-25 发布日期:2025-04-14
作者简介:韩静，女，1987年出生，博士研究生。主要研究方向为异种材料激光焊接技术。E-mail:295485252@qq.com;石玗(通信作者)，男，1973年出生，博士，教授，博士研究生导师。主要研究方向为焊接物理及先进连接技术、智能焊接及自动化、激光加工及再制造。E-mail:shiyu@lut.edu.cn
基金资助:
国家自然科学基金(52075235)、甘肃省自然科学基金(21JR7RA233)和中央引导地方科技发展资金(23ZYQA308)资助项目。

Study on the Microstructure and Mechanical Properties of Copper/Steel Joints Welded by Non-uniform Laser Source

HAN Jing¹, SHI Yu¹, LI Guang¹, ZHANG Hang², LU Gang²

1. State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals, Lanzhou University of Technology, Lanzhou 730050;
2. Zhejiang E. O. Paton Welding Technology Institute, Hangzhou 311200

Received:2024-04-17 Revised:2024-12-25 Published:2025-04-14

摘要/Abstract

摘要： 铜钢复合结构因兼具成本和性能的优势应用广泛，但存在物性参数差异，焊接难度大。传统均匀热源下焊接接头成分偏析大、铜侧热影响区软化严重。采用全域功率可调激光振镜焊接系统，设计非均匀热源以满足两种材料对热量的不同需求，研究了三种不同的功率模式对Cu/304SS异种接头元素扩散、微观组织及性能的影响。结果表明，Cu与Fe侧的功率比为6比4时，接头产生了最大程度的液相分离，焊缝中铜和钢的固溶体均匀分散，接头具有最低的元素偏析程度以及最小的软化程度，抗拉强度最大(211 MPa)，为铜母材的93%(226 MPa)。研究结果为铜钢异种接头焊接过程能量分布的灵活调控提供新的手段。

关键词: 振镜, 显微组织, 异种金属, 力学性能, 机制

Abstract: Copper-steel composite structures are widely used due to their advantages in both cost and performance. However, there are differences in material physical properties and difficulties in welding. Traditional welding methods using a uniform heat source often lead to significant elemental segregation in the joints and severe softening in the copper side heat-affected zone. A full-domain power modulation laser oscillating welding system is employed to design a non-uniform heat source to meet the different heat requirements of the two materials. Three different power modes were investigated to study their effects on the elements diffusion, microstructure, and properties of Cu/304SS dissimilar joints. The findings revealed that when the power ratio between the copper and steel sides was set at 6:4, the joint exhibited the maximum degree of liquid phase separation, with the solid solution of copper and steel uniformly dispersed in the weld. The joint exhibited the lowest degree of elemental segregation and the least softening. Additionally, it demonstrated a maximum tensile strength of 211 MPa, which was 93 % of the copper base material (226 MPa). It provides a novel approach for the flexible control of energy distribution during the welding process of dissimilar joints between copper and steel.

Key words: oscillation, microstructure, dissimilar metal, mechanical properties, mechanism

中图分类号:

TG156

韩静, 石玗, 李广, 张航, 陆刚. 非均匀激光热源焊接铜/钢接头的组织及力学性能研究[J]. 机械工程学报, 2025, 61(6): 151-159.

HAN Jing, SHI Yu, LI Guang, ZHANG Hang, LU Gang. Study on the Microstructure and Mechanical Properties of Copper/Steel Joints Welded by Non-uniform Laser Source[J]. Journal of Mechanical Engineering, 2025, 61(6): 151-159.

参考文献

[1] SADEGHIAN A，IQBAL N. A review on dissimilar laser welding of steel-copper, steel-aluminum,aluminum-copper, and steel-nickel for electric vehicle battery manufacturing[J]. Optics & Laser Technology，2022，146：107595.
[2] LI Jianmin，CAI Yuanzheng，YAN Fei，et al. Porosity and liquation cracking of dissimilar Nd:YAG laser welding of SUS304 stainless steel to T2 copper[J]. Optics & Laser Technology，2020，122：105881.
[3] NGUYEN Q，AZADKHOU A，AKBARI M，et al. Experimental investigation of temperature field and fusion zone microstructure in dissimilar pulsed laser welding of austenitic stainless steel and copper[J]. Journal of Manufacturing Processes，2020，56：206-215.
[4] JOSHI G R，BADHEKA V J. Processing of bimetallic steel-copper joint by laser beam welding[J]. Materials and Manufacturing Processes，2019，34(11)：1232-1242.
[5] CHEN Shuhai，HUANG Jihua，XIA Jun，et al. Influence of processing parameters on the characteristics of stainless steel/copper laser welding[J]. Journal of Materials Processing Technology，2015，222：43-51.
[6] THOMAS N，MATHEW A，GEORGE K，et al. Microstructural and mechanical properties evaluation of tungsten inert gas-welded 316 stainless steel and pure copper joint[J]. Metallography, Microstructure, and Analysis，2020，9(5)：678-684.
[7] GAO Ming，ZHANG Yazhou，MENG Yunfei. Interface homogenization and its relationship with tensile properties of laser-arc hybrid welded Al/steel butt-joint via beam oscillation[J]. Journal of Materials Science，2021，56(25)：14126-14138.
[8] CHEN Cong，XIANG Yunzhong，GAO Ming. Weld formation mechanism of fiber laser oscillating welding of dissimilar aluminum alloys[J]. Journal of Manufacturing Processes，2020，60：180-187.
[9] KAR J，ROY S K，ROY G G. Effect of beam oscillation on electron beam welding of copper with AISI-304 stainless steel[J]. Journal of Materials Processing Technology，2016，233：174-185.
[10] JIANG Zhenguo，CHEN Xi，YU Kun，et al. Improving fusion zone microstructure inhomogeneity in dissimilar-metal welding by laser welding with oscillation[J]. Materials Letters，2020，261：126995.
[11] WANG L L，WEI H L，XUE J X，et al. A pathway to microstructural refinement through double pulsed gas metal arc welding[J]. Scripta Materialia，2017，134：61-65.
[12] 史杰. 铜-钢异种材料焊接工艺及组织演变行为研究[D]. 西安：西安理工大学，2019. SHI Jie. Fusion welding on copper-steel dissimilar materials and joint microstructure evolution[D]. Xi’an：Xi’an University of Technology，2019.
[13] SAHUL M，TOMČÍKOVÁ E，SAHUL M，et al. Effect of disk laser beam offset on the microstructure and mechanical properties of copper-AISI 304 stainless steel dissimilar metals joints[J]. Metals，2020，10(10)：1294.
[14] 陈永城，罗子艺，张宇鹏，等. 紫铜-304不锈钢激光焊接接头显微组织及力学性能[J]. 材料导报，2019，33(1)：325-329. CHEN Yongcheng，LUO Ziyi，ZHANG Yupeng，et al. Microstructure and mechanical properties of copper/304 stainless steel joints welded by laser beam[J]. Materials Reports，2019，33(1)：325-329.
[15] CHEN Shuhai，HUANG Jihua，XIA Jun，et al. Microstructural characteristics of a stainless steel/copper dissimilar joint made by laser welding[J]. Metallurgical and Materials Transactions. A, Physical Metallurgy and Materials Science，2013，44(8)：3690-3696.
[16] NING Jie，ZHANG Linjie，YIN Xianqing，et al. Mechanism study on the effects of power modulation on energy coupling efficiency in infrared laser welding of highly-reflective materials[J]. Materials & Design，2019，178：107871.
[17] SCHWEIER M，HEINS J F，HAUBOLD M W，et al. Spatter formation in laser welding with beam oscillation[J]. Physics Procedia，2013，41：20-30.
[18] CHEN Cong，ZHOU Haipeng，WANG Changjian，et al. Laser welding of ultra-high strength steel with different oscillating modes[J]. Journal of Manufacturing Processes，2021，68：761-769.
[19] HAO Kangda，LI Geng，GAO Ming，et al. Weld formation mechanism of fiber laser oscillating welding of austenitic stainless steel[J]. Journal of Materials Processing Technology，2015，225：77-83.
[20] HAN Jing，SHI Yu，ZHANG Gang，et al. Minimizing defects and controlling the morphology of laser welded aluminum alloys using power modulation-based laser beam oscillation[J]. Journal of Manufacturing Processes，2022，83：49-59.
[21] ROY C，PAVANAN V V，VISHNU G，et al. Characterization of metallurgical and mechanical properties of commercially pure copper and AISI 304 dissimilar weldments[J]. Procedia Materials Science，2014，5：2503-2512.
[22] 蔡远征. T2紫铜/304不锈钢异种合金激光自熔焊工艺研究[D]. 武汉：华中科技大学，2018. CAI Yuanzheng. Investigation on dissimilar alloy laser welding of T2 copper/SUS 304[D]. Wuhan：Huazhong University of Science & Technology，2018.
[23] 李静. T2-304焊接接头组织与性能分析及其匹配焊材的研究[D]. 西安：西安理工大学，2020. LI Jing. Microstructure and performance analysis and research on matching welding materials of T2-304 joint[D]. Xi’an：Xi’an University of Technology，2020.

非均匀激光热源焊接铜/钢接头的组织及力学性能研究

Study on the Microstructure and Mechanical Properties of Copper/Steel Joints Welded by Non-uniform Laser Source

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘翰儒, 陈桂映, 许泽林, 彭世通, 郭嘉楠, 刘伟嵬, 王奉涛. 基于SERepVGG-A2的轻量化卷积神经网络在熔池状态识别中的应用[J]. 机械工程学报, 2025, 61(3): 440-448.
[2]	张刚, 刘忠义, 张程, 朱明, 石玗. 铝合金振镜激光-双脉冲CMT复合增材熔滴过渡特性[J]. 机械工程学报, 2025, 61(2): 120-129.
[3]	杨纯攀, 王小伟, 李雪松, 杨东青, 黄勇, 彭勇, 王克鸿. 超声冲击辅助电弧增材制造18Ni-350马氏体时效钢组织性能研究[J]. 机械工程学报, 2025, 61(2): 162-171.
[4]	吴贯之, 陈楠楠, 石华兵, 刘坤山, 孔谅, 王敏. 摆动激光填丝焊工艺参数对碳钢搭接角焊缝成形与力学性能的影响[J]. 机械工程学报, 2025, 61(2): 172-180.
[5]	杨超雄, 张兆栋, 沙禹垚, 刘黎明. 倾斜基板铝合金增材制造尺寸规律及性能研究[J]. 机械工程学报, 2025, 61(1): 326-334.
[6]	孔玲, 王玉辉, 杨浩坤, 彭艳. Fe-Mn-Al-C系奥氏体基低密度钢使役性能研究进展[J]. 机械工程学报, 2024, 60(8): 34-47.
[7]	任志英, 黄子豪, 方荣政, 王秦伟, 莫继良, 秦红玲. 金属橡胶无序式网格互穿结构的热力学性能研究[J]. 机械工程学报, 2024, 60(8): 165-175.
[8]	李力, 王一轩, 罗芬, 张文涛, 赵巍, 李小强. 钎焊时间对TiH₂-65Ni+TiB₂钎料钎焊连接TiAl合金接头的影响[J]. 机械工程学报, 2024, 60(8): 176-185.
[9]	顾玉芬, 鲁娜, 石玗, 孙青岭. 16MnDR钢焊接接头组织特性及在氢氟酸环境中的腐蚀行为[J]. 机械工程学报, 2024, 60(8): 196-203.
[10]	陈伟, 赵杰, 朱利斌, 曹海波. 增材制造低活化钢研究现状及展望[J]. 机械工程学报, 2024, 60(7): 312-333.
[11]	郑洋, 赵梓昊, 刘伟, 余政哲, 牛伟, 雷贻文, 孙荣禄. 高性能镁合金增材制造技术研究进展[J]. 机械工程学报, 2024, 60(7): 385-400.
[12]	鲍鑫宇, 麻永林, 程桥, 苏怡卉, 王杰, 邢淑清. 脉冲磁场熔体处理对Al-Si-Mg-Cu-Ni合金DC铸造凝固组织和力学性能的影响[J]. 机械工程学报, 2024, 60(6): 279-286.
[13]	王志颖, 李天福, 许文纲, 孙闯, 张军辉, 徐兵, 严如强. 降噪混合注意力变分自编码器及其在轴向柱塞泵故障诊断中的应用[J]. 机械工程学报, 2024, 60(4): 167-177.
[14]	周甜, 蔡力勋, 韩光照. 用于延性材料力学性能测定的圆柱平面-小冲杆试验新方法与应用[J]. 机械工程学报, 2024, 60(4): 316-325.
[15]	高强, 王健, 张严, 郑旭阳, 吕昊, 殷国栋. 拓扑优化方法及其在运载工程中的应用与展望[J]. 机械工程学报, 2024, 60(4): 369-390.