弹性环配合紧度对转子动力学特性的影响

doi:10.3901/JME.2023.13.124

机械工程学报 ›› 2023, Vol. 59 ›› Issue (13): 124-132.doi: 10.3901/JME.2023.13.124

扫码分享

弹性环配合紧度对转子动力学特性的影响

罗忠^1,2, 刘家希^1,2, 李雷^1,2, 吴法勇³, 葛向东³

1. 东北大学机械工程与自动化学院沈阳 110819;
2. 东北大学航空动力装备振动及控制教育部重点实验室沈阳 110819;
3. 中国航发沈阳发动机研究所沈阳 110015

收稿日期:2022-07-07 修回日期:2022-12-09 出版日期:2023-07-05 发布日期:2023-08-15
通讯作者: 罗忠(通信作者),男,1978 年出生,博士,教授,博士研究生导师。主要研究方向为机械动力学与控制、模型试验技术与方法等。E-mail:zhluo@mail.neu.edu.cn
作者简介:刘家希,男,1997年出生,硕士,主要研究方向为航空发动机弹性支承结构设计及动力学特性分析。E-mail:864588462@qq.com
基金资助:
国家自然科学基金(11872148，U1908217)，广东省粤佛联合重点基金(2020B1515120015)资助项目。

Dynamic Characteristics Analysis of Rotor System with Fitting Tightness of Elastic Ring Support Structure

LUO Zhong^1,2, LIU Jiaxi^1,2, LI Lei^1,2, WU Fayong³, GE Xiangdong³

1. School of Mechanical Engineering&Automation, Northeastern University, Shenyang 110819;
2. Key Laboratory of Vibration and Control of Aero-Propulsion System Ministry of Education, Northeastern University, Shenyang 110819;
3. AECC Shenyang Engine Research Institute, Shenyang 110015

Received:2022-07-07 Revised:2022-12-09 Online:2023-07-05 Published:2023-08-15

摘要/Abstract

摘要： 弹性环式支承结构作为航空发动机中典型的弹性支承结构，其配合紧度很大程度上影响支承系统的刚度，进一步影响转子系统动力学特性，但相关研究尚少。因此，首先建立了弹性环式支承结构的有限元模型，分析了配合紧度对其刚度及强度特性的影响，并发现可通过分段刚度出现时的位移与凸台高度之间的关系来判断弹性环式式支承结构的配合紧度，然后搭建了相关实验台与测试结果对比，验证了仿真结果的正确性，最后建立了考虑弹性环式支承结构配合紧度的转子系统有限元模型，研究了其对转子系统动力学特性的影响。研究表明：过盈配合下的弹性环式支承结构会导致转子系统临界转速升高，间隙配合会导致临界转速降低，并会引起转子系统非线性振动，研究结果可为采用弹性环式支承结构的转子支承系统设计提供理论参考。

关键词: 弹性环式支承结构, 配合紧度, 支承刚度, 有限元, 转子系统

Abstract: As the typical elastic support structure in aeroengine, the fitting tightness of elastic ring support structure greatly affects the stiffness of the support system, and further affects the dynamic characteristics of the rotor system, but there are few relevant researches. Therefore, the finite element model of elastic ring support structure is established firstly, and the influence of fitting tightness on its stiffness and strength is analyzed. It is found that the fitting tightness of the elastic ring support structure can be judged by the relationship between the displacement when the segment stiffness appears and the height of the boss. Then carry out the relevant experimental platform. The correctness of the simulation results are verified by comparing with the experimental results. Finally, the finite element model of rotor system considering the fitting mode of the elastic ring supporting structure is established, and the influence of the model on the characteristics of the rotor system dynamics is studied. The results show that the elastic ring support structure with interference fit will increase the critical speed of the rotor system, while the clearance fit will decrease the critical speed, and cause nonlinear vibration of the rotor system. The research results can provide theoretical reference for the design of the rotor support system with elastic ring support structure.

Key words: elastic ring support structure, fitting tightness, support stiffness, finite element method, rotor system

中图分类号:

V231
TB123

罗忠, 刘家希, 李雷, 吴法勇, 葛向东. 弹性环配合紧度对转子动力学特性的影响[J]. 机械工程学报, 2023, 59(13): 124-132.

LUO Zhong, LIU Jiaxi, LI Lei, WU Fayong, GE Xiangdong. Dynamic Characteristics Analysis of Rotor System with Fitting Tightness of Elastic Ring Support Structure[J]. Journal of Mechanical Engineering, 2023, 59(13): 124-132.

参考文献

[1] WANG M,HAN Q,WEN B,et al. Modal characteristics and unbalance responses of fan rotor system with flexible support structures in aero-engine[J]. Proceedings of the Institution of Mechanical Engineers Part G Journal of Aerospace Engineering,2017,231(g9):1686-1705.
[2] LUO Z,LI L,YANG Y,et al. Experimental and numerical investigations on novel models for mechanical behaviors of the elastic ring in aero-engine[J]. Proceedings of the Institution of Mechanical Engineers,Part C:Journal of Mechanical Engineering Science. 2021:2141141582.
[3] WANG Z,LIU Z,ZHANG G,et al. Dynamic characteristics of elastic ring squeeze film damper. Industrial Lubrication and Tribology,2019,71(10),1144-1151.
[4] MA Y,ZHU H,ZHANG D,et al. Experimental investigation on dynamic mechanical behavior of the elastic ring support with metal rubber[C]//ASME 2013 International Mechanical Engineering Congress and Exposition,2013.
[5] 刘勇,文立华. 弹性环式柔性支撑有限元分析及结构参数选择[J]. 机械科学与技术,2012,31(11):1744-1747. LIU Yong,WEN Lihua. FEM analysis and structural parameter selection of elastic rings[J]. Mechanical Science and Technology for Aerospace Engineering,2012,31(11):1744-1747.
[6] HEIDARI H R,SAFARPOUR P. Design and modeling of a novel active squeeze film damper[J]. Mechanism and Machine Theory,2016,105:235-243.
[7] BAI C,XU Q,WANG J. Effects of flexible support stiffness on the nonlinear dynamic characteristics and stability of a turbopump rotor system[J]. Nonlinear Dynamics,2011,64:237-252.
[8] DOUSTI S,GERAMI A,DOUSTI M. A numerical CFD analysis on supply groove effects in high pressure,open end squeeze film dampers[J]. International Journal of Engineering Innovation & Research,2016,5(7):80-89.
[9] SIEW C C,HILL M,HOLMES R. Evaluation of various fluid-film models for use in the analysis of squeeze film dampers with a central groove[J]. Tribology International,2002,35(8):533-547.
[10] 王四季,廖明夫,刘永泉,等. 航空发动机轴承外环装配工艺引起的转子系统非线性振动[J]. 航空动力学报,2015,30(1):82-89. WANG Siji,LIAO Mingfu,LIU Yongquan. Nonlinear vibration of rotor systems caused by assembly process of a bearing outer ring of an aero-engine[J]. Journal of Aerospace Power,2015,30(1):82-89.
[11] DILIGENSKIY D S,NOVIKOV D K. Studying of manufacturing tolerance influence on the performance of GTE rotor elastic rings[J]. Procedia Engineering,2017,176(Complete):483-497.
[12] ZHANG W,DING Q. Elastic ring deformation and pedestal contact status analysis of elastic ring squeeze film damper[J]. Journal of Sound & Vibration,2015,346:314-327.
[13] 苏春峰. 弹性环式挤压油膜阻尼器动力特性研究[D]. 沈阳:沈阳航空工业学院,2009. SU Chunfeng. Study on dynamic characteristics of elastic ring squeeze film damper[D]. Shenyang:Shenyang Institute of Aeronautical Engineering,2009.
[14] 李岩,廖眀夫,王四季. 配合关系对弹性环式挤压油膜阻尼器减振特性的影响[J]. 振动与冲击,2020,39(11):232-238. LI Yan,LIAO Mingfu,WANG Siji. Effect on vibrating attenuation by the fit of elastic ring squeeze film damper[J]. Journal of Vibration and Shock,2020,39(11):232-238.
[15] ISHIDA Y,INAGAKI M,EJIMA R,et al. Nonlinear resonances and self-excited oscillations of a rotor caused by radial clearance and collision[J]. Nonlinear Dynamics,2009,57(4):593-605.
[16] YABUNO H,KASHIMURA T,INOUE T,et al. Nonlinear normal modes and primary resonance of horizontally supported Jeffcott rotor[J]. Nonlinear Dynamics,2011,66(3):377-387.
[17] CHEN G. Vibration modelling and verifications for whole aero-engine[J]. Journal of Sound & Vibration,2015,349:163-176.
[18] 刘闯,陈国栋,杨阳,等. 基于有限元仿真的弹性环刚度特性分析[J]. 沈阳航空航天大学学报,2019,36(3):8-13. LIU Chuang,CHEN Guodong,YANG Yang,et al. Stiffness analysis of elastic ring based on finite element simulation[J]. Journal of Shenyang Aerospace University,2019,36(3):8-13.
[19] HAN Z,MA Z,ZHANG W,et al. Dynamic analysis of an elastic ring squeeze film damper supported rotor using a semi-analytic method[J]. Engineering Applications of Computational Fluid Mechanics,2020,14(1):1263-1278.

弹性环配合紧度对转子动力学特性的影响

Dynamic Characteristics Analysis of Rotor System with Fitting Tightness of Elastic Ring Support Structure

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴杰, 党嘉强, 李宇罡, 陈东, 安庆龙, 王浩伟, 陈明. 应力超声滚压表面强化机理和抗疲劳性能研究[J]. 机械工程学报, 2024, 60(9): 127-136.
[2]	蒋飞, 赵升吨, 范淑琴, 王可心, 陈超. 剥肋滚压复合工艺及其设备研究[J]. 机械工程学报, 2024, 60(8): 132-142.
[3]	罗忠, 石宝龙, 吴法勇, 李玉奇, 刘凯宁, 张小霞. 考虑装配工艺的螺栓连接转子系统振动特性研究[J]. 机械工程学报, 2024, 60(8): 396-406.
[4]	赵承伟, 张文豪, 龚天诚, 张逸云, 王长涛, 罗先刚. 平面光学元件超平整吸附装载的优化设计与分析[J]. 机械工程学报, 2024, 60(5): 241-248.
[5]	潘鑫, 张馨, 卢加乔, 吴海琦. 基于超声电机精稳调控的转子不平衡自愈执行装置设计与试验研究[J]. 机械工程学报, 2024, 60(4): 449-457.
[6]	曾少昔, 赵春田, 李红梅. 铁磁材料漏磁信号对拉伸应力的响应研究[J]. 机械工程学报, 2024, 60(20): 68-76.
[7]	赵欣, 黄金杰. 基于RSM-RVEA的FDM增材制造工艺参数优化方法[J]. 机械工程学报, 2024, 60(19): 277-297.
[8]	姚丹, 张捷, 王瑞乾, 肖新标. 阻尼处理对铝型材结构隔声特性的影响分析[J]. 机械工程学报, 2024, 60(18): 299-309.
[9]	李怡然, 尧军平, 梁超群, 肖鹏, 陈国鑫, 李步炜. 基于三维微观结构的SiC/AZ91D复合材料单轴拉伸过程中裂纹萌生扩展机制[J]. 机械工程学报, 2024, 60(16): 160-170.
[10]	周剑, 徐宏坤, 刘焜. 基于微观孔隙演变的Ti-6Al-4V粉末高速压制致密化机理研究[J]. 机械工程学报, 2024, 60(16): 180-189.
[11]	赵宇辉, 赵吉宾, 李明玥, 何振丰, 王志国, 贺晨. 激光熔化沉积TC4钛合金电涡流检测仿真及亚表面缺陷检测[J]. 机械工程学报, 2024, 60(14): 34-41.
[12]	尚建勤, 田硕, 盖鹏涛, 陈福龙, 曾元松. 带筋整体壁板拉弯预应力喷丸成形技术及其应用[J]. 机械工程学报, 2024, 60(14): 97-108.
[13]	赵雷, 武言, 徐连勇, 韩永典, 熊昱. 纳入拘束效应的焊接接头蠕变裂纹扩展速率预测方法[J]. 机械工程学报, 2024, 60(14): 126-138.
[14]	赵妍, 李射, 崔向阳. 基于新型三角形壳元和多重动态自适应方法的薄板冲压成形分析[J]. 机械工程学报, 2024, 60(14): 153-165.
[15]	邓智铭, 黄土地, 黄洪钟, 尉询楷, 王浩. 变工况条件下角接触球轴承疲劳剥落故障演化加速试验载荷谱研究[J]. 机械工程学报, 2024, 60(13): 193-204.