基于空气动力学透镜的线性聚焦3D打印送粉喷头设计与性能研究

doi:10.3901/JME.2023.11.253

机械工程学报 ›› 2023, Vol. 59 ›› Issue (11): 253-263.doi: 10.3901/JME.2023.11.253

扫码分享

基于空气动力学透镜的线性聚焦3D打印送粉喷头设计与性能研究

厉鸿韬, 黄延禄, 杨永强

华南理工大学机械与汽车工程学院广州 510641

收稿日期:2022-07-01 修回日期:2023-02-04 出版日期:2023-06-05 发布日期:2023-07-19
通讯作者: 黄延禄(通信作者),男,1972年出生,博士,副教授,硕士研究生导师。主要研究方向为激光加工、增材制造与数学建模与数值计算。E-mail:yanlu@scut.edu.cn
作者简介:厉鸿韬,男,1995年出生。主要研究方向为激光增材制造。E-mail:hongtao1533@163.com
基金资助:
国家自然科学基金资助项目(U2001218)

Design and Performance Research of Linear Focus 3D Printing Powder Nozzle Based on Aerodynamic Lens

LI Hongtao, HUANG Yanlu, YANG Yongqiang

School of Mechanical & Automotive Engineering, South China University of Technology, Guangzhou 510641

Received:2022-07-01 Revised:2023-02-04 Online:2023-06-05 Published:2023-07-19

摘要/Abstract

摘要： 提出一种基于“空气动力学透镜”的具有粉末线性聚焦功能的新型3D打印送粉喷头，可以使粉末流在喷头出口一定距离内均保持汇聚状态。设计了该新型喷头的内腔结构，建立了粉末颗粒在喷头中的汇聚运动模型，分析了颗粒运动的斯托克斯数S、空气动力学透镜第一节孔径d_f、孔径收缩率δ以及粉末进入喷头的入射角α对粉末颗粒聚焦性能的影响。研究结果表明：对于粒径为15～25 μm的316L颗粒，该喷头可以将粉末颗粒聚焦成半径1.55 mm的粉末流，且在喷嘴外20 mm范围内均保持良好的汇聚状态；实验结果和计算结果基本一致。该新型空气动力学透镜3D打印送粉喷头的颗粒汇聚性能明显优于传统喷头，对于促进沉积增材制造的灵活性和适用性具有重要意义。

关键词: 3D打印, 送粉喷头, 空气动力学透镜, 粉末流

Abstract: A new type of 3D printing powder feeding nozzle with linear focusing based on “aerodynamic lens” is proposed, which can keep the powder stream in a convergent state within a certain distance from the nozzle outlet. The inner structure of the nozzle is designed, and the convergent movement model of powder particles in the nozzle is established. These factors are analyzed for studying the focusing performance of the powder particles: the Stokes number of the particle (S), the first aerodynamic lens aperture (d_f), the aperture shrinkage (δ) and the incident angle of the powder entering the nozzle (α). The research results show that for 316L particles with a particle size of 15-25 μm, the nozzle can focus the particles into a powder stream with a radius of 1.55 mm, and the powder stream maintains a good convergence state within 20 mm outside the nozzle. The numerical results are basically consistent with the experimental ones. The particle aggregation performance of the new aerodynamic lens 3D printing powder feeding nozzle is significantly better than that of the traditional nozzle, which is of great significance to promote the flexibility and adaptability of deposition additive manufacturing.

Key words: 3D printing, powder feeding nozzle, aerodynamic lens, powder flow

中图分类号:

TN249

厉鸿韬, 黄延禄, 杨永强. 基于空气动力学透镜的线性聚焦3D打印送粉喷头设计与性能研究[J]. 机械工程学报, 2023, 59(11): 253-263.

LI Hongtao, HUANG Yanlu, YANG Yongqiang. Design and Performance Research of Linear Focus 3D Printing Powder Nozzle Based on Aerodynamic Lens[J]. Journal of Mechanical Engineering, 2023, 59(11): 253-263.

参考文献

[1] DEBROY T，WEI H L，ZUBACK J S，et al. Additive manufacturing of metallic components - Process，structure and properties[J]. Progress in Materials Science，2018，92: 112-224.
[2] WEI H L，LIU F Q，LIAO W H，et al. Prediction of spatiotemporal variations of deposit profiles and inter-track voids during laser directed energy deposition[J]. Additive Manufacturing，2020，34:101219.
[3] GUO Chenguang，HE Shunzhi，YUE Haitao，et al. Prediction modelling and process optimization for forming multi-layer cladding structures with laser directed energy deposition[J]. Optics and Laser Technology，2021，134:106607.
[4] TAN J H K，SING S L，YEONG W Y. Microstructure modelling for metallic additive manufacturing:A review[J]. Virtual and Physical Prototyping，2020，15(1):87-105.
[5] 吴东江，黄云飞，赵大可，等. 直接激光沉积熔体自生氧化铝/钛酸铝复合陶瓷微观组织及力学性能[J]. 机械工程学报，2022，58(14):212-222. WU Dongjiang，HUANG Yunfei，ZHAO Dake，et al. Microstructure and mechanical properties of melt growth alumina/aluminum titanate composite ceramics prepared by directed laser deposition[J]. Journal of Mechanical Engineering，2022，58(14):212-222.
[6] 李祺祺，温耀杰，张百成，等. 梯度功能合金的增材制造技术研究进展[J]. 机械工程学报，2021，57(22):184-200. LI Qiqi，WEN Yaojie，ZHANG Baicheng，et al. Research progress of functional graded alloy prepared by additive manufacturing technology[J]. Journal of Mechanical Engineering，2021，57(22):184-200.
[7] LIU Hao，HE Xiuli，YU Gang，et al. Numerical simulation of powder transport behavior in laser cladding with coaxial powder feeding[J]. Science China (Physics，Mechanics & Astronomy)，2015，58(10):34-43.
[8] 邓珍波，梅筱琴，向召伟，等. 载气式同轴送粉3D打印喷头粉末流场数值分析[J]. 四川大学学报，2016，48(S2):165-172. DENG Zhenbo，MEI Xiaoqin，XIANG Zhaowei，et al. Numerical analysis of powder flow filed on coaxial feeding nozzle forced by gas in 3D printing[J]. Journal of Sichuan University，2016，48(S2):165-172.
[9] 蔡齐飞，石世宏，李春生，等. 激光熔覆快速成形光内送粉方式的研究[J]. 苏州大学学报，2009，29(2):43-45+73. CAI Qifei，SHI Shihong，LI Chunsheng，et al. Study on inside laser powder feeding of laser cladding rapid prototyping[J]. Journal of Suzhou University，2009，29(2):43-45+73.
[10] LIU P，ZIEMANN P J，KITTELSON D B，et al. Generating particle beams of controlled dimensions and divergence:I. Theory of particle motion in aerodynamic lenses and nozzle expansions[J]. Aerosol Science and Technology，1995，22(3):193-313.
[11] WANG X，MCMURRY P H. A design tool for aerodynamic lens systems[J]. Aerosol Science and Technology，2006，40(5):320-334.
[12] LEE K S，HWANG T H，KIM S H，et al. Numerical simulations on aerodynamic focusing of particles in a wide size range of 30 nm-10μm[J]. Aerosol Science and Technology，2013，47(9):1001-1008.
[13] CAHILL J F，DARLINGTON T K，WANG X，et al. Development of a high-pressure aerodynamic lens for focusing large particles (4-10μm) into the aerosol time-of-flight mass spectrometer[J]. Aerosol Science and Technology，2014，48(9):948-956.

[1]	赵欣, 黄金杰. 基于RSM-RVEA的FDM增材制造工艺参数优化方法[J]. 机械工程学报, 2024, 60(19): 277-297.
[2]	黄金杰, 赵欣. 3D打印中的分层计算研究进展[J]. 机械工程学报, 2024, 60(17): 235-262.
[3]	孙江涛, 张净凯, 程坦, 范志永, 叶春生, 蔡道生, 魏青松. 吸热墨水喷射3D打印实验平台研制与自制墨水打印试验研究[J]. 机械工程学报, 2024, 60(17): 263-271.
[4]	侯佳奇, 张广明, 于志浩, 李印, 马令轩, 韩志峰, 石凯, 郭辰旭, 兰红波. 平板电极电场驱动多喷头喷射高效微3D打印方法和规律研究[J]. 机械工程学报, 2024, 60(17): 310-320.
[5]	喻康, 傅建中, 贺永. 面向软组织缺损修复的组织工程支架研究进展[J]. 机械工程学报, 2024, 60(15): 255-271.
[6]	刘明良, 唐颀, 田小永, 刘腾飞, 秦滢杰, 李涤尘. 连续纤维增强加筋圆柱壳回转3D打印工艺及其轴压性能研究[J]. 机械工程学报, 2024, 60(15): 283-290.
[7]	彭子龙, 吴金印, 王萌杰, 李一楠, 兰红波. 电场驱动微尺度3D打印掩膜电解加工微结构[J]. 机械工程学报, 2024, 60(15): 420-436.
[8]	王福吉, 王公硕, 王洪全, 付饶, 吴博, 王琦. 短-连续碳纤维同步增强热塑性复合材料预浸线材制备及3D打印工艺分析[J]. 机械工程学报, 2024, 60(11): 283-295.
[9]	穆英朋, 刘富初, 张驰, 黄捷飞, 刘鑫, 韩光超, 樊自田, 许峰. 水溶性氧化钙陶瓷型芯的挤出式3D打印参数优化与表面精度控制研究[J]. 机械工程学报, 2024, 60(1): 170-178.
[10]	兰红波, 李红珂, 钱垒, 张广明, 于志浩, 孙鹏, 许权, 赵佳伟, 王飞, 朱晓阳. 电场驱动喷射沉积微纳3D打印及其在先进电路和电子制造中的应用[J]. 机械工程学报, 2023, 59(9): 230-251.
[11]	罗来马, 汤俊宇, 吴玉程. WC-Co硬质合金的成型工艺研究进展[J]. 机械工程学报, 2023, 59(8): 60-73.
[12]	李汶海, 张广明, 于尊, 韩志峰, 马令轩, 彭子龙, 肖淼, 徐林, 西永明, 兰红波. 3D打印导电生物支架的研究进展与挑战[J]. 机械工程学报, 2023, 59(23): 186-210.
[13]	李佩锡, 周德志, 杨长明, 饶玮祎, 林峰, 欧阳礼亮. 生物3D打印研究进展：动物、植物及微生物细胞的增材制造[J]. 机械工程学报, 2023, 59(19): 237-252.
[14]	李波波, 刘靖驰, 李晓强, 邱成鸿, 卢秉恒. 基于电脉冲的铁基非晶薄带增材制造试验研究[J]. 机械工程学报, 2023, 59(15): 247-254.
[15]	王权岱, 强昊文, 叶思彤, 李鹏阳, 郑建明, 李言. 光-热双固复合材料3D打印成型数值模拟及实验验证[J]. 机械工程学报, 2023, 59(15): 293-303.

基于空气动力学透镜的线性聚焦3D打印送粉喷头设计与性能研究

Design and Performance Research of Linear Focus 3D Printing Powder Nozzle Based on Aerodynamic Lens

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价