磨料浆体射流辅助TBM刀盘截割性能分析

doi:10.3901/JME.2024.15.379

机械工程学报 ›› 2024, Vol. 60 ›› Issue (15): 379-392.doi: 10.3901/JME.2024.15.379

扫码分享

磨料浆体射流辅助TBM刀盘截割性能分析

刘送永^1,2, 周方跃^1,2, 割泽伸一³, 郭楚文⁴, 李洪盛^1,2

1. 中国矿业大学机电工程学院徐州 221116;
2. 中国矿业大学江苏省矿山智能采掘装备协同创新中心徐州 221008;
3. 东京大学新领域创成科学研究科千叶 277-8589 日本;
4. 中国矿业大学低碳能源与动力工程学院徐州 221116

收稿日期:2023-08-17 修回日期:2024-01-15 出版日期:2024-08-05 发布日期:2024-09-24
作者简介:刘送永，男，1981年出生，博士，教授，博士研究生导师。主要研究方向为矿体高效破碎机理与技术、地下空间快速掘进技术及装备。E-mail：lsycumt@163.com
周方跃(通信作者)，男，1993年出生，博士，讲师。主要研究方向为机械/水射流高效破岩理论与技术、隧道掘进装备结构设计与研发。E-mail：fangyuezhou@outlook.com
基金资助:
江苏省杰出青年基金(BK20211531)、安徽理工大学高层次引进人才科研启动基金(2023yjrc34)和江苏省基础研究计划(自然科学基金)青年基金(BK20210516)资助项目。

Analysis of Cutting Performance of TBM Cutter Head Assisted by Abrasive Slurry Jet

LIU Songyong^1,2, ZHOU Fangyue^1,2, SHINICHI W³, GUO Chuwen⁴, LI Hongsheng^1,2

1. School of Mechatronic Engineering, China University of Mining and Technology, Xuzhou 221116;
2. Jiangsu Province and Education Ministry Co-sponsored Collaborative Innovation Center of Intelligent Mining Equipment, China University of Mining and Technology, Xuzhou 221008;
3. Graduate School of Frontier Sciences, University of Tokyo, Chiba, 277-8589 Japan;
4. School of Low-Carbon Energy and Power Engineering, China University of Mining and Technology, Xuzhou 221116

Received:2023-08-17 Revised:2024-01-15 Online:2024-08-05 Published:2024-09-24

摘要/Abstract

摘要： 针对高地应力环境以及高硬度、强磨蚀性等复杂岩层条件下隧道施工所面临的滚刀频繁失效问题，利用高压水射流辅助机械刀具破岩技术的降载减磨特性将切割能力相比纯水射流更强的磨料浆体射流引入TBM刀盘，并基于预切缝联合滚刀破岩载荷特性对射流喷嘴于刀盘上的布置方案进行合理设计，在此基础上结合已有试验条件开展水射流-刀盘对混凝土岩样的室内截割试验，探究岩样抗压强度、射流压力、刀盘转速与推进速度对刀盘截割性能的影响规律以及各因素间的相关关系。研究结果表明：岩样抗压强度、刀盘转速与推进速度的增加均会推升刀盘扭矩与推进阻力水平，磨料浆体射流的存在有助于改善刀盘的载荷状态并削弱相关因素的影响水平，且射流压力愈高效果愈显著，但由于高压水射流切割破碎岩石比能相对于机械刀具更高，磨料浆体射流的引入在提升刀盘掘进速度的同时亦拖累了施工的经济性。各因素对刀盘扭矩的影响主次顺序依次为岩样抗压强度、刀盘转速、推进速度、射流压力，而对刀盘推进阻力的影响主次顺序则依次为岩样抗压强度、推进速度、射流压力、刀盘转速。

关键词: 磨料浆体射流, TBM刀盘, 扭矩, 推进阻力, 比能

Abstract: In response to the frequent failure of disc cutters in tunnel construction under high ground stress and complex rock formations such as high hardness and strong abrasion, the abrasive slurry jet with stronger cutting ability than pure water jet was introduced into the TBM cutter head based on the load and wear reduction characteristics of rock breaking technology with mechanical cutter assisted by high-pressure water jet. The layout scheme of jet nozzles on the cutter head was reasonably designed based on the rock breaking load characteristics of pre-slit combined disc cutter, and the indoor cutting tests of water jet-cutter head on concrete rock specimen were conducted in combination with existing experimental conditions to explore the influence of rock specimen compressive strength, jet pressure, cutter head rotation and advancing speed on the cutting performance of the cutter head, as well as the correlation between various factors. The results indicate that the increase in rock specimen compressive strength, cutter head rotation and advancing speed will push up the torque and propulsion resistance levels of the cutter head. The presence of abrasive slurry jet helps to improve the load state of the cutter head and weaken the influence level of related factors, and the higher the jet pressure, the more significant the effect. However, the introduction of abrasive slurry jet not only increases the tunnelling speed of the cutter head, but also drags down the economy of construction due to the higher rock breaking specific energy of high-pressure water jet compared to mechanical tools. The primary and secondary order of the influence of various factors on the torque of the cutterhead is rock specimen compressive strength, cutter head rotation speed, cutter head advancing speed, and jet pressure, while what on the propulsion resistance of the cutter head is rock specimen compressive strength, cutter head advancing speed, jet pressure, and cutter head rotation speed.

Key words: abrasive slurry jet, TBM cutter head, torque, propulsion resistance, specific energy

中图分类号:

U455

刘送永, 周方跃, 割泽伸一, 郭楚文, 李洪盛. 磨料浆体射流辅助TBM刀盘截割性能分析[J]. 机械工程学报, 2024, 60(15): 379-392.

LIU Songyong, ZHOU Fangyue, SHINICHI W, GUO Chuwen, LI Hongsheng. Analysis of Cutting Performance of TBM Cutter Head Assisted by Abrasive Slurry Jet[J]. Journal of Mechanical Engineering, 2024, 60(15): 379-392.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2024.15.379

http://www.cjmenet.com.cn/CN/Y2024/V60/I15/379

参考文献

[1] ZHAO Jian，GONG Qiuming，EISENSTEN Z.Tunnelling through a frequently changing and mixed ground: A case history in Singapore[J].Tunnelling and Underground Space Technology，2007，22(4):388-400.
[2] JAMAL R.Hard rock tbm cutterhead modeling for design and performance prediction[J].Geomechanics and Tunnelling，2008，1(1):18-28.
[3] XIA Yimin，OUYANG Tao，ZHANG Xinming，et al.Mechanical model of breaking rock and force characteristic of disc cutter[J].Journal of Central South University，2012，19(7):1846-1852.
[4] 程永亮，钟掘，暨智勇，等.TBM刀盘地质适应性设计方法及其应用[J].机械工程学报，2018，54(1):1-9. CHENG Yongliang，ZHONG Jue，JI Zhiyong，et al.Geological adaptive design method and application of TBM cutterhead[J].Journal of Mechanical Engineering，2018，54(1):1-9.
[5] 王虹，王步康，张小峰，等.煤矿智能快掘关键技术与工程实践[J].煤炭学报，2021，46(7):2068-2083. WANG Hong，WANG Bukang，ZHANG Xiaofeng，et al.Key technology and engineering practice of intelligent rapid heading in coal mine[J].Journal of China Coal Society，2021，46(7):2068-2083.
[6] 张洪伟，胡兆锋，程敬义，等.深部高温矿井大断面岩巷TBM智能掘进技术——以“新矿1号”TBM为例[J].煤炭学报，2021，46(7):2174-2185. ZHANG Hongwei，HU Zhaofeng，CHENG Jingyi，et al.TBM techniques for intelligent excavating large-section rock roadway in the deep high-temperature coal mine: Application of TBM in Xinkuang No.1[J].Journal of China Coal Society，2021，46(7):2174-2185.
[7] YAGIZ S.Utilizing rock mass properties for predicting TBM performance in hard rock condition[J].Tunnelling and Underground Space Technology，2008，23(3):326-339.
[8] ROSTAMI J.Performance prediction of hard rock Tunnel Boring Machines (TBMs) in difficult ground[J].Tunnelling and Underground Space Technology，2016，57(SI):173-182.
[9] FARROKH E，KIM D Y.A discussion on hard rock TBM cutter wear and cutterhead intervention interval length evaluation[J].Tunnelling and Underground Space Technology，2018，81:336-357.
[10] YANG Shengqi，TAO Yan，XU Peng，et al.Large-scale model experiment and numerical simulation on convergence deformation of tunnel excavating in composite strata[J].Tunnelling and Underground Space Technology，2019，94:103133.
[11] 谭青，易念恩，夏毅敏，等.TBM滚刀破岩动态特性与最优刀间距研究[J].岩石力学与工程学报，2012，31(12):2453-2464. TAN Qing，YI Nianen，XIA Yimin，et al.Research on rock dynamic fragmentation characteristics by TBM cutters and cutter spacing optimization[J].Chinese Journal of Rock Mechanics and Engineering，2012，31(12):2453-2464.
[12] 谭青，易念恩，夏毅敏，等.全断面岩石掘进机滚刀最优刀间距计算公式研究[J].岩土力学，2016，37(3):883-892. TAN Qing，YI Nianen，XIA Yimin，et al.Study of calculation equation of TBM disc cutter optimal spacing[J].Rock and Soil Mechanics，2016，37(3):883-892.
[13] HUO Junzhou，SUN Wei，CHEN Jing，et al.Optimal disc cutters plane layout design of the full-face rock tunnel boring machine (tbm) based on a multi-objective genetic algorithm[J].Journal of Mechanical Science and Technology，2010，24(2):521-528.
[14] FARMER I，GARRITTY P，GLOSSOP N.Operational characteristics of full face tunnel boring machines[C]//Rapid Excavation and Tunnelling Conference.New Orleans，1987:188-201.
[15] ZHANG Qian，QU Chuanyong，KANG Yilan，et al.Identification and optimization of energy consumption by shield tunnel machines using a combined mechanical and regression analysis[J].Tunnelling and Underground Space Technology，2012，28:350-354.
[16] CICCU R，GROSSO B.Improvement of disc cutter performance by water jet assistance[J].Rock Mechanics and Rock Engineering，2014，47(2):733-744.
[17] CHENG Jianlong，JIANG Zihao，HAN Weifeng，et al.Breakage mechanism of hard-rock penetration by TBM disc cutter after high pressure water jet precutting[J].Engineering Fracture Mechanics，2020，240:107320.
[18] 聂佳辉，吴志鑫，雷磊，等.TBM的刀具改性与辅助破岩技术研究现状[J].机械，2021，48(12):1-10，19. NIE Jiahui，WU Zhixin，LEI Lei，et al.Review on the modification and assistant rock breaking techniques of TBM cutters[J].Machinery，2021，48(12):1-10，19.
[19] LU Yiyu，TANG Jiren，GE Zhaolong，et al.Hard rock drilling technique with abrasive water jet assistance[J].International Journal of Rock Mechanics and Mining Science，2013，60:47-56.
[20] LIU Songyong，LIU Zenghui，CUI Xinxia，et al.Rock breaking of conical cutter with assistance of front and rear water jet[J].Tunnelling and Underground Space Technology，2014，42:78-86.
[21] LIU Songyong，LIU Xiaohui，CHEN Junfeng，et al.Rock breaking performance of a pick assisted by high-pressure water jet under different configuration modes[J].Chinese Journal of Mechanical Engineering，2015，28(3):607-617.
[22] 徐福通，卢景景，周辉，等.预切槽和TBM机械滚刀的新型联合破岩模式研究[J].岩土力学，2021，42(5):1363-1372. XU Futong，LU Jingjing，ZHOU Hui，et al.Research on combined rock-breaking mode of pre-cutting groove and TBM mechanical cutter[J].Rock and Soil Mechanics，2021，42(5):1363-1372.
[23] 周辉，徐福通，卢景景，等.切槽对TBM刀具破岩机制的影响研究[J].岩土力学，2022，43(3):625-634. ZHOU Hui，XU Futong，LU Jingjing，et al.Study on the influence of pre-cutting groove on rock breaking mechanism of TBM disc cutter[J].Rock and Soil Mechanics，2022，43(3):625-634.
[24] 翟乾智，周建军，李宏波，等.双护盾TBM滚刀磨损及换刀判定案例分析[J].隧道建设，2019，39(12):2081-2087. ZHAI Qianzhi，ZHOU Jianjun，LI Hongbo，et al.A case study on double-shield TBM disc cutter wear and replacement estimation[J].Tunnel Construction，2019，39(12):2081-2087.
[25] LIU Songyong，ZHOU Fangyue，LI Hongsheng，et al.Experimental investigation of hard rock breaking using a conical pick assisted by abrasive water jet[J].Rock Mechanics and Rock Engineering，2020，53(9):4221-4230.
[26] LIU Songyong，CUI Song，LI Hongsheng，et al.Impact characteristics of rock breaking using a conical pick assisted with abrasive slurry jet[J].Engineering Fracture Mechanics，2022，271:108647.
[27] 刘送永，杜长龙，江红祥.机械-水射流联合破岩及在矿山机械中应用[M].北京:科学出版社，2017. LIU Songyong，DU Changlong，JIANG Hongxiang.Mechanical-water jet combined rock breaking and its application in mining machinery[M].Beijing:Science Press，2017.
[28] 张龙仁，王晓敏.国外高压水细射流在掘进机上的应用[J].矿山机械，1979(1):1-5. ZHANG Longren，WANG Xiaomin.Application of high pressure water fine jet on roadheader abroad[J].Mining and Processing Equipment，1979(1):1-5.
[29] 顾大钊.模拟岩石机械破碎的相似材料的选择及其配比[J].中国矿业大学院报，1988(3):33-37. GU Dazhao.A study of analogous materials for simulating mechanical rock breaking and the proportion of their components[J].International Journal of Mining Science and Technology，1988(3):33-37.
[30] 王梦恕，李典璜，张镜剑，等.岩石隧道掘进机(TBM)施工及工程实例[M].北京:中国铁道出版社，2004. WANG Mengshu，LI Dianhuang，ZHANG Jingjian，et al.Construction and engineering example of rock tunnel boring machine (TBM)[M].Beijing:China Railway Publishing House，2004.
[31] ROXBOROUGH F F，PHILLIPS H R.Rock excavation by disc cutter[J].International Journal of Rock Mechanics & Mining Sciences & Geomechanics Abstracts，1975，12(12):361-366.

磨料浆体射流辅助TBM刀盘截割性能分析

Analysis of Cutting Performance of TBM Cutter Head Assisted by Abrasive Slurry Jet

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张年华, 张永康, 陈继成, 李朋涛, 李焱, 张辉. 基于多智能体理论的分布式驱动车辆ESC-TVC鲁棒协同控制策略研究[J]. 机械工程学报, 2026, 62(8): 365-381.
[2]	金智林, 高峥恒. 多模式混合动力汽车扭矩分配及切换品质优化控制研究[J]. 机械工程学报, 2026, 62(8): 398-409.
[3]	黄小敏, 郭桐, 阙富民, 李昕铭, 刘昊, 林添良. 端面先导压力控制二级配流高压径向柱塞马达新构型及其容积效率特性[J]. 机械工程学报, 2026, 62(6): 409-418.
[4]	赵继云, 满家祥, 于鸣泉, 韩静, 王云飞, 曹超. 低速大扭矩阀配流内曲线高水基液压马达设计理论与试验研究[J]. 机械工程学报, 2025, 61(4): 365-379.
[5]	董光旭, 林睿深, 罗亚军, 彭裕阳, 余文涯, 张秉豪, 邱兰. 基于应变测量的动-静扭矩传感方法研究[J]. 机械工程学报, 2025, 61(3): 314-324.
[6]	陈俊翔, 高春莹, 孔祥东, 李智, 艾超. 超大型电控液压挖掘机动力系统匹配研究[J]. 机械工程学报, 2025, 61(22): 317-328.
[7]	彭程, 陈俐. 混合动力车辆滑摩起动离合器扭矩实时估计方法[J]. 机械工程学报, 2025, 61(16): 217-226.
[8]	白鑫, 沈童, 王凡勋, 殷国栋, 王金湘, 方睿祺, 李新修, 梁晋豪. 基于驾驶人操纵稳定域的分布式驱动电动汽车多模态扭矩分配策略研究[J]. 机械工程学报, 2025, 61(14): 166-183.
[9]	张俊, 吴成阳, 方汉良, 孙载超, 王凯龙, 汤腾飞. Z4型冗余驱动并联操作器的驱动特性研究[J]. 机械工程学报, 2024, 60(7): 66-78.
[10]	赵承伟, 张文豪, 龚天诚, 张逸云, 王长涛, 罗先刚. 平面光学元件超平整吸附装载的优化设计与分析[J]. 机械工程学报, 2024, 60(5): 241-248.
[11]	宋阳, 曹华军, 张金, 刘磊, 张琼之. 纤维随机分布CFRP高速铣削比能模型与表面质量优化[J]. 机械工程学报, 2024, 60(1): 65-74.
[12]	杨宇星, 鲍永杰, 王金龙, 杜凤鸣. 复合材料螺接力学行为精细化有限元分析方法[J]. 机械工程学报, 2022, 58(22): 198-207.
[13]	李慧莱, 凌振飞, 王泽正, 孙茂文, 刘浩, 欧阳小平, 李斌斌. 高扭矩密度仿人机器人驱动单元研究[J]. 机械工程学报, 2022, 58(18): 192-204.
[14]	曹天赐, 聂营, 王苏宁, 温昊驹, 马洪强. 基于管式应变天平的飞艇螺旋桨飞行测力系统[J]. 机械工程学报, 2022, 58(16): 301-308.
[15]	张昌青, 师文辰, 罗德春, 王树文, 刘晓, 崔国胜, 陈波阳, 辛舟, 芮执元. 锥形端面对铝/钢连续驱动摩擦焊接头界面温度及摩擦扭矩影响的研究[J]. 机械工程学报, 2022, 58(10): 95-102.