考虑变幂数的畸变动力学相似试验模型设计方法及试验研究

doi:10.3901/JME.2020.23.107

机械工程学报 ›› 2020, Vol. 56 ›› Issue (23): 107-117.doi: 10.3901/JME.2020.23.107

扫码分享

考虑变幂数的畸变动力学相似试验模型设计方法及试验研究

李雷^1,2, 罗忠^1,2,3, 何凤霞^1,2, 张文笛^1,2

1. 东北大学机械工程与自动化学院沈阳 110819;
2. 东北大学航空动力装备振动及控制教育部重点实验室沈阳 110819;
3. 大连理工大学工业装备结构分析国家重点实验室大连 116024

收稿日期:2019-09-25 修回日期:2020-08-20 出版日期:2020-12-05 发布日期:2021-01-11
作者简介:李雷,男,1994年出生,博士研究生。主要研究方向航空发动机转子系统动力学相似理论与方法。E-mail:lileineu@126.com;罗忠(通信作者),男,1978年出生,博士,教授,博士研究生导师。主要研究方向为机械动力学与控制、模型试验理论与方法。E-mail:zhluo@mail.neu.edu.cn
基金资助:
国家自然科学基金（11872148，U1908217）和教育部基本科研业务费专项资金（N2003012，N2003013，N180703018，N170308028）资助项目。

Design Method of Distorted Dynamics Similitude Test Model Considering Variable Power and Experimental Study

LI Lei^1,2, LUO Zhong^1,2,3, HE Fengxia^1,2, ZHANG Wendi^1,2

1. School of Mechanical Engineering & Automation, Northeastern University, Shenyang 110819;
2. Key Laboratory of Vibration and Control of Aero-Propulsion System (Ministry of Education), Northeastern University, Shenyang 110819;
3. State Key Laboratory of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian 116024

Received:2019-09-25 Revised:2020-08-20 Online:2020-12-05 Published:2021-01-11

摘要/Abstract

摘要： 动力学相似理论广泛应用于大型结构的振动试验，其中畸变相似用于解决结构的设计参数不满足等比例缩放时的相似问题，针对畸变相似关系中幂数为定值导致预测精度低的问题，提出考虑变幂数的畸变动力学相似试验模型设计方法。首先，在敏感性分析与中心差分理论推导的幂数表达式的基础上，将中心差分的范围不断扩大得到一组随相似比变化的幂数。采用最小二乘法将这组幂数拟合为关于相似比的函数并建立相似关系。然后，在多盘转子系统的数值算例中将变幂数法与文献中的两种方法进行对比，结果表明，变幂数法的预测精度较文献中的方法有很大提高。最后，通过试验研究验证了数值算例中动力学模型及临界转速求解的正确有效性。相似关系的建立是以模型的临界转速为基础，因此也验证了数值算例中的相似预测结果。

关键词: 畸变相似, 相似关系, 多盘转子系统, 敏感性分析, 变幂数

Abstract: Dynamics similitude theory is widely used in vibration test of large structures. Distorted similitude is used to solve the similitude problem that the design parameters of structures do not satisfy equal scaling. Aiming at the problem of low prediction accuracy caused by the fixed power in distorted scaling laws, this paper proposes a design method of distorted dynamics similitude test model considering variable power. Firstly, on the basis of the power of scaling factor deduced by the sensitivity analysis and the central difference theory, the range of the central difference theory is expanded to obtain a set of powers which is used to fit a function related with the scaling factor by the least square method. Then, the proposed method is compared with two methods in literatures in the numerical example of multi-disc rotor system. It is found that the accuracy of the proposed method is much higher than that of the methods in literatures. Finally, the dynamic model and its solution of the numerical example are verified by the experimental study. The prediction results in the numerical example are also considered verified since the scaling laws are developed based on the critical speeds of the dynamic model.

Key words: distorted similitude, scaling laws, multi-disc rotor system, sensitivity analysis, variable power

中图分类号:

TH113

李雷, 罗忠, 何凤霞, 张文笛. 考虑变幂数的畸变动力学相似试验模型设计方法及试验研究[J]. 机械工程学报, 2020, 56(23): 107-117.

LI Lei, LUO Zhong, HE Fengxia, ZHANG Wendi. Design Method of Distorted Dynamics Similitude Test Model Considering Variable Power and Experimental Study[J]. Journal of Mechanical Engineering, 2020, 56(23): 107-117.

参考文献

[1] KRAYTERMAN B,SABNIS G M. Similitude theory:Plates and shells analysis[J]. Journal of Engineering Mechanics,1984,110(9):1247-1263.
[2] REZAEEPAZHAND J,SIMITSES G J,STARNES J H. Use of scaled-down models for predicting vibration response of laminated plates[J]. Composite Structures,1995,30(4):419-426.
[3] REZAEEPAZHAND J,YAZDI A A. Similitude requirements and scaling laws for flutter prediction of angle-ply composite plates[J]. Composites Part B-Engineering,2011,42(1):51-56.
[4] SIMITSES G J,REZAEEPAZHAND J. Structural similitude and scaling laws for buckling of cross-ply laminated plates[J]. Journal of Thermoplastic Composite Materials,1995,8(3):240-251.
[5] FROSTIG Y,SIMITSES G J. Similitude of sandwich panels with a'soft'core in buckling[J]. Composites Part B-Engineering,2004,35(6-8):599-608.
[6] YAZDI A A. Prediction flutter boundaries of laminated cylindrical shells using scaling laws[J]. Journal of Aerospace Engineering,2014,27(1):86-92.
[7] ASL M E,NIEZRECKI C,SHERWOOD J,et al. Experimental and theoretical similitude analysis for flexural bending of scaled-down laminated I-beams[J]. Composite Structures,2017,176:812-822.
[8] ASL M E,NIEZRECKI C,SHERWOOD J,et al. Vibration prediction of thin-walled composite I-beams using scaled models[J]. Thin-Walled Structures,2017,113:151-161.
[9] UNGBHAKORN V,SINGHATANADGID P. Similitude invariants and scaling laws for buckling experiments on anti-symmetrically laminated plates subjected to biaxial loading[J]. Composite Structures,2003,59(4):455-465.
[10] SINGHATANADGID P,UNGBHAKORN V. Scaling laws for buckling of polar orthotropic annular plates subjected to compressive and torsional loading[J]. Thin-Walled Structures,2005,43(7):1115-1129.
[11] UNGBHAKORN V,WATTANASAKULPONG N. Structural similitude and scaling laws of anti-symmetric cross-ply laminated cylindrical shells for buckling and vibration experiments[J]. International Journal of Structural Stability and Dynamics,2007,7(4):609-627.
[12] SINGHATANADGID P,SONGKHLA A N. An experimental investigation into the use of scaling laws for predicting vibration responses of rectangular thin plates[J]. Journal of Sound and Vibration,2008,311(1-2):314-327.
[13] OSHIRO R E,ALVES M. Predicting the behaviour of structures under impact loads using geometrically distorted scaled models[J]. Journal of the Mechanics and Physics of Solids,2012,60(7):1330-1349.
[14] 杨俊杰.相似理论与结构模型试验[M].武汉:武汉理工大学出版社,2005. YANG Junjie. Similitude theory and structural model test[M]. Wuhan:Wuhan University of Technology Press,2005.
[15] LUO Zhong,ZHU Yunpeng,ZHAO Xueyan,et al. Determination method of dynamic distorted scaling laws and applicable structure size intervals of a rotating thin-wall short cylindrical shell[J]. Proceedings of the Institution of Mechanical Engineers Part C-Journal of Mechanical Engineering Science,2015,229(5):806-817.
[16] 王艾伦,黄礼坤.转子变态模型与原型的动力相似研究[J].机械设计,2013,30(10):11-15. WANG Ailun,HUANG Likun. Study on the dynamics similitude between the distorted model and the prototype of rotor systems[J]. Journal of Machine Design,2013,30(10):11-15.
[17] 李哲,王贡献,胡吉全,等.基于惯性半径相似岸桥模型的地震试验[J].振动.测试与诊断,2016,36(5):972-978,1028. LI Zhe,WANG Gongxian,HU Jiquan,et al. Seismic experimental research on cross section radius of inertia similar for dynamic model of container cranes[J]. Journal of Vibration,Measurement& Diagnosis,2016,36(5):972-978,1028.
[18] 缪辉,臧朝平.航空发动机低压转子系统的动力学相似设计方法[J].航空动力学报,2020,35(4):766-776. LIAO Hui,ZANG Chaoping. Dynamic similarity design method for aero-engine low-pressure rotor system[J]. Journal of Aerospace Power,2020,35(4):766-776.
[19] 李天娥,孙晓颖,武岳,等.软式平流层飞艇气弹模型相似参数分析[J].工程力学,2019,36(3):240-246,256. LI Tiane,SUN Xiaoying,WU Yue,et al. Similarity parameter analysis of aeroelastic model for non-rigid stratospheric airship[J]. Engineering Mechanics,2019,36(3):240-246,256.
[20] 田永强,蔡晋生,张正科,等.结冰风洞实验中的相似理论[J].北京航空航天大学学报,2020,46(2):359-370. TIAN Yongqiang,CAI Jinsheng,ZHANG Zhengke,et al. Similarity theory in icing wind tunnel test[J]. Journal of Beijing University of Aeronautics and Astronautics,2020,46(2):359-370.
[21] 左宪帅,王立新,刘海良,等.缩比模型模拟全尺寸飞机自动着舰的相似关系[J].航空学报,2019,40(12):6-22. ZUO Xianshuai,WANG Lixin,LIU Hailiang,et al. Similarty for simulating automatic carrier landing process of full-scale aircraft with scaled-model[J]. Acta Aeronautica Sinica,2019,40(12):6-22.
[22] LUO Zhong,ZHU Yunpeng,ZHAO Xueyan,et al. Determining dynamic scaling laws of geometrically distorted scaled models of a cantilever plate[J]. Journal of Engineering Mechanics,2016,142(4):115-123.
[23] 罗忠,郭健,朱云鹏,等.考虑静强度要求的旋转直板叶片试验模型相似设计方法[J].机械工程学报,2016,52(9):79-85. LUO Zhong,GUO Jian,ZHU Yunpeng,et al. Considering the requirements of static strength for the rotating straight blade similar experimental model design method[J]. Journal of Mechanical Engineering,2016,52(9):79-85.
[24] 罗忠,王有,韩清凯,等.圆环薄板类构件畸变相似关系的确定方法[J].机械工程学报,2017,53(23):14-19. LUO Zhong,WANG You,HAN Qingkai,et al. Determining method of distorted scaling laws of the thin walled annular plates'structures[J]. Journal of Mechanical Engineering,2017,53(23):14-19.
[25] ADAMS C,BOS J,SLOMSKI E M,et al. Scaling laws obtained from a sensitivity analysis and applied to thin vibrating structures[J]. Mechanical Systems and Signal Processing,2018,110:590-610.
[26] CASABURO A,PETRONE G,FRANCO F,et al. A review of similitude methods for structural engineering[J]. Applied Mechanics Reviews,2019,71(3):30802.
[27] COUTINHO C P,BAPTISTA A J,RODRIGUES J D. Reduced scale models based on similitude theory:a review up to 2015[J]. Engineering Structures,2016,119:81-94.
[28] 赵林海,许俊杰,刘伟宁,等.基于Levenberg-Marquardt算法和广义S-变换的无绝缘轨道电路补偿电容的故障检测[J].控制理论与应用,2010,27(12):1612-1617,1622. ZHAO Linhai,XU Junjie,LIU Weining,et al. Compensation capacitor fault detection method in jointless track circuit based on Levenberg-Marquardt algorithm and generalized S-transform[J]. Control Theory& Applications,2010,27(12):1612-1617,1622.
[29] WU Jiajang. Prediction of lateral vibration characteristics of a full-size rotor-bearing system by using those of its scale models[J]. Finite Elements in Analysis and Design,2007,43(10):803-816.
[30] 罗忠,朱云鹏,韩清凯,等.动力学相似理论及在结构振动分析中的应用研究评述与展望[J].机械工程学报,2016,52(23):114-134. LUO Zhong,ZHU Yunpeng,HAN Qingkai,et al. Review and prospect for dynamic similitude theory and its applications in the structure vibration[J]. Journal of Mechanical Engineering,2016,52(23):114-134.
[31] 姜彦翠,刘献礼,吴石,等.考虑结合面和轴向力的主轴系统动力学特性[J].机械工程学报,2015,51(19):66-74. JIANG Yancui,LIU Xianli,WU Shi,et al. Dynamics characteristics of the spindle system with the interface and axial milling force[J]. Journal of Mechanical Engineering,2015,51(19):66-74.
[32] 陈果.航空发动机整机振动耦合动力学模型及其验证[J].航空动力学报,2012,27(2):241-254. CHEN Guo. A coupling dynamic model for whole aero-engine vibration and its verification[J]. Journal of Aerospace Power,2012,27(2):241-254.
[33] MA Hui,LU Yang,WU Zhiyuan,et al. A new dynamic model of rotor-blade systems[J]. Journal of Sound and Vibration,2015,357:168-194.
[34] QIN Zhaoye,HAN Qingkai,CHU Fulei. Analytical model of bolted disk-drum joints and its application to dynamic analysis of jointed rotor[J]. Proceedings of the Institution of Mechanical Engineers Part C-Journal of Mechanical Engineering Science,2014,228(4):646-663.
[35] YANG Hui,DENG Zongquan,LIU Rongqiang,et al. Optimizing the qusai-static folding and deploying of thin-walled tube flexure hinges with double slots[J]. Chinese Journal of Mechanical Engineering,2014,27(2):279-286.

考虑变幂数的畸变动力学相似试验模型设计方法及试验研究

Design Method of Distorted Dynamics Similitude Test Model Considering Variable Power and Experimental Study

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 9

编辑推荐

Metrics

本文评价

[1]	刘瑞伟, 郭宏伟, 刘荣强, 唐德威, 王洪祥, 邓宗全. 大口径索肋张拉式折展天线索网结构动力学特性分析[J]. 机械工程学报, 2019, 55(12): 1-8.
[2]	郑似玉, 滕金芳, 羌晓青. 叶片加工超差对高压压气机性能影响和敏感性分析[J]. 机械工程学报, 2018, 54(2): 216-224.
[3]	林赉贶, 夏毅敏, 贾连辉, 吴遁, 沈斌, 张旭辉. TBM边缘滚刀组合破岩特性及其影响因素敏感性评价[J]. 机械工程学报, 2018, 54(1): 18-26.
[4]	罗忠, 王有, 韩清凯, 江志农. 圆环薄板类构件畸变相似关系的确定方法[J]. 机械工程学报, 2017, 53(23): 14-19.
[5]	沈宇洲, 罗斌, 谢国瑞, 郭正兴, 姜鹏. FAST反射面索网支承结构误差敏感性分析和多误差耦合分析[J]. 机械工程学报, 2017, 53(17): 10-16.
[6]	张扬, 张维刚, 马桃, 唐婷. 基于全局敏感性分析和动态代理模型的复杂非线性系统优化设计方法[J]. 机械工程学报, 2015, 51(4): 126-131.
[7]	翁卫兵;邵举平. 多重不确定环境下战略联盟供应链物流计划优化[J]. , 2014, 50(4): 192-202.
[8]	程为彬;傅钟炜;钟彦儒. Boost变换器中混沌行为参数敏感性分析[J]. , 2008, 44(4): 246-252.
[9]	董玉华;余大涛;高惠临. Monte-Carlo法计算含缺陷油气输送管线的失效概率[J]. , 2004, 40(2): 136-140.