横向载荷作用下螺栓临界松动载荷数值计算方法研究

doi:10.3901/JME.2018.05.173

机械工程学报 ›› 2018, Vol. 54 ›› Issue (5): 173-178.doi: 10.3901/JME.2018.05.173

扫码分享

横向载荷作用下螺栓临界松动载荷数值计算方法研究

张明远, 鲁连涛, 唐明明, 曾东方

西南交通大学牵引动力国家重点实验室成都 610031

收稿日期:2017-04-10 修回日期:2017-12-12 出版日期:2018-03-05 发布日期:2018-03-05
通讯作者: 鲁连涛(通信作者),男,1965年出生,博士,研究员,博士研究生导师。主要研究方向为金属材料超长寿命疲劳与断裂;表面改性技术对疲劳强度的改善机理及应用;压装轴的微动疲劳等。E-mail:luliantao@swjtu.edu.cn
作者简介:张明远,男,1990年出生,博士研究生。主要研究方向为螺栓松动机理,机械结构失效分析。E-mail:myzhang90@163.com
基金资助:
国家重点实验室自主研究课题（2015TPL_T16）和高速铁路基础研究联合基金（U1334206）资助项目。

Research on Numerical Calculation Method of Critical Load for Bolt Loosening under Transverse Loading

ZHANG Mingyuan, LU Liantao, TANG Mingming, ZENG Dongfang

State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu 610031

Received:2017-04-10 Revised:2017-12-12 Online:2018-03-05 Published:2018-03-05

摘要/Abstract

摘要： 为明确螺栓抵抗松动的能力，指导螺栓在使用中的选型，以抑制螺纹面局部滑移为防松条件，通过对同一螺纹面周向不同位置的受力进行分析，推导得到了横向载荷作用下螺栓临界松动载荷的数值计算公式。采用横向振动试验装置和该数值计算方法，分别测试和计算了尺寸规格为M5的螺栓在夹紧力为2 000 N、2 500 N时的临界松动载荷。结果表明，夹紧力为2 000 N时临界松动载荷的试验与计算结果分别为302.5 N、280.3 N，2 500 N时试验与计算结果分别为372.5 N和350.4 N。两种夹紧力条件下试验与计算结果相对误差分别为7.3%（2 000 N）和5.9%（2 500 N），这验证了该数值计算方法的准确性及可靠性。基于该公式，分析了螺栓结构参数对临界松动载荷的影响。结果表明，增大夹紧力、螺纹面摩擦因数、螺栓直径以及牙型角，降低螺栓夹紧长度、螺纹升角，可以增大临界松动载荷，提高螺栓抵抗松动的能力。

关键词: 局部滑移, 临界载荷, 螺栓, 数值计算, 松动

Abstract: In order to evaluate the anti-loosening ability of bolt and guide the selection of the bolt in use, a numerical formula of critical load for bolt loosening is obtained through the force analysis in different circumferential positions of thread. Inhibiting localized thread slip is the condition of avoiding loosening in the formula derivation. The critical loads of the M5 bolts under 2 000 N and 2 500 N preloads are tested by the transverse vibration device and calculated by the numerical formula, respectively. The results show that the critical loads obtained by test and calculation are 302.5 N and 280.3 N for the bolt with 2 000 N preload, 372.5 N and 350.4 N for the bolt with 2 500 N preload. The relative errors between the test and calculation results are 7.3% (2 000 N) and 5.9% (2 500 N) respectively, confirming the accuracy and reliability of the numerical formula. Then, the effect of the structure parameters of bolt on the critical load for bolt loosening is analyzed based on the numerical formula. The results show that increasing the clamping load, the thread friction coefficient, the bolt diameter, the thread angle, and decreasing the clamping length, the lead angle, can contribute to increasing this critical load, and improve the anti-loosening ability of bolt.

Key words: bolt, critical load, localized slip, loosening, numerical calculation

中图分类号:

TH122

张明远, 鲁连涛, 唐明明, 曾东方. 横向载荷作用下螺栓临界松动载荷数值计算方法研究[J]. 机械工程学报, 2018, 54(5): 173-178.

ZHANG Mingyuan, LU Liantao, TANG Mingming, ZENG Dongfang. Research on Numerical Calculation Method of Critical Load for Bolt Loosening under Transverse Loading[J]. Journal of Mechanical Engineering, 2018, 54(5): 173-178.

参考文献

[1] GOODIER J N,SWEENEY R J. Loosening by vibration of threaded fastenings[J]. Mechanical Engineering,1945,67:798-802.
[2] JIANG Yanyao,ZHANG Ming. An experimental study of self-Loosening of bolted joints[J]. Journal of Mechanical Design,2004,126:925-931.
[3] JUNKER G H. New criteria for self loosening of fasteners under vibration[J]. SAE Transactions,1969,78:314-315.
[4] PAI N G,HESS D P. Experimental study of loosening of threaded fasteners due to dynamic shear loads[J]. Journal of Sound and Vibration,2002,253(3):585-602.
[5] 王崴,徐浩,马跃,等. 振动工况下螺栓连接自松弛机理研究[J]. 振动与冲击,2014,33(22):198-202. WANG Wei,XU Hao,MA Yue,et al. Self-loosening mechanism of bolted joints under vibration[J]. Journal of Vibration and Shock,2014,33(22):198-202.
[6] PAI N G,HESS D P. Three dimensional finite element analysis of threaded fastener loosening due to dynamic shear load[J]. Engineering Failure Analysis,2002,9:383-402.
[7] JIANG Xiangjun,ZHU Yongsheng,HONG Jun,et al. Investigation into the loosening mechanism of bolt in curvic coupling subjected to transverse loading[J]. Engineering Failure Analysis,2013,32(3):360-373.
[8] LIU Jianhua,OUYANG Huajiang,PENG Jinfang,et al., Experimental and numerical studies of bolted joints subjected to axial excitation[J]. Wear,2016,346:66-77.
[9] LIU Jianhua,OUYANG Huajiang,FENG Zhiqiang,et al. Study on self-loosening of bolted joints excited by dynamic axial load[J]. Tribology International,2017,115:432-451.
[10] ECCLES W,SHERRINGTON I,ARNELL R D. Towards an understanding of the loosening characteristics of prevailing torque nuts[J]. ARCHIVE Proceedings of the Institution of Mechanical Engineers Part C:Journal of Mechanical Engineering Science,2010,224(2):483-495.
[11] 李维荣. 螺纹紧固件防松技术和试验方法研究[D]. 合肥:合肥工业大学,2005. LI Weirong. The research of technology to prevent from loosening and method of testing for thread fastener[D]. Hefei:Hefei University of Technology,2005.
[12] CROCCOLO D,AGOSTINIS M D,VINCENZI N. Failure analysis of bolted joints:Effect of friction coefficients in torque-preloading relationship[J]. Engineering Failure Analysis,2011,18:364-373.
[13] 陈维金. 德国与我国机车车辆用螺栓技术的对比分析[J]. 铁道技术监督,2011,39(4):2-7. CHEN Weijin. Comparative analysis of the bolt technology using in locomotive of China and Germany[J]. Railway Quality Control,2011,39(4):2-7.

[1]	罗忠, 石宝龙, 吴法勇, 李玉奇, 刘凯宁, 张小霞. 考虑装配工艺的螺栓连接转子系统振动特性研究[J]. 机械工程学报, 2024, 60(8): 396-406.
[2]	唐玉玲, 闫福棣, 张峻霞, 周振功, 郭颖, 姜美娇. 碳/碳编织复合材料连接结构的拉脱性能分析[J]. 机械工程学报, 2023, 59(18): 196-206.
[3]	雷声, 毛宽民, 田微, 孔德龙. 基于模型修正的螺栓结合部虚拟材料参数识别及应用[J]. 机械工程学报, 2022, 58(21): 274-284.
[4]	李志农, 陈世尧, 乔芳, 周世健, 王冬. 盘轴过盈力不足-支座松动耦合故障的转子系统的振动特性研究[J]. 机械工程学报, 2022, 58(11): 109-119.
[5]	巩浩, 刘检华, 冯慧华. 螺纹连接松动机理和防松方法研究综述[J]. 机械工程学报, 2022, 58(10): 326-347,360.
[6]	蒋博彦, 肖千豪, 杨筱沛, 诸永定, 王军. 多翼离心风机蜗壳小型化设计数值研究[J]. 机械工程学报, 2021, 57(9): 175-182.
[7]	李朝峰, 乔瑞环, 苗雪阳, 江雨霖. 螺栓连接界面非线性建模及其参数辨识方法研究[J]. 机械工程学报, 2021, 57(7): 78-86.
[8]	刘检华, 张飞凯, 丁晓宇. 弹塑性粗糙表面实际接触面积演变规律研究[J]. 机械工程学报, 2021, 57(7): 109-116.
[9]	王梁, 罗建, 胡勇, 夏洪超, 姚建华. 激光同轴熔注球形WC增强颗粒的工艺参数研究[J]. 机械工程学报, 2021, 57(7): 253-261.
[10]	李莹, 陈冬京, 王博众, 佟海生, 孔祥东, 张晋. 静置油液中单气泡运动规律研究[J]. 机械工程学报, 2021, 57(24): 93-101.
[11]	潘勤学, 常梅乐, 潘瑞鹏, 徐晓宇, 李双阳, 张云淼. 螺栓轴向应力的非线性超声检测技术研究[J]. 机械工程学报, 2021, 57(22): 88-95.
[12]	吕雪梅, 王曦, 罗明生. 考虑接触热阻的高速列车制动盘热机耦合行为分析[J]. 机械工程学报, 2021, 57(22): 296-304.
[13]	李玲, 王晶晶, 史小辉, 仝美娟, 解妙霞. 基于修正Iwan模型的螺栓结合面非线性建模研究[J]. 机械工程学报, 2021, 57(19): 93-101.
[14]	胡军, 杨德斌. 一种基于变形运动矢量分析法的转子耦合故障机理建模[J]. 机械工程学报, 2021, 57(15): 91-104.
[15]	潘嘉诚, 关振群, 曾岩, 孙伟程. 柱壳结构螺栓法兰连接非线性刚度分析[J]. 机械工程学报, 2021, 57(1): 28-39.

横向载荷作用下螺栓临界松动载荷数值计算方法研究

Research on Numerical Calculation Method of Critical Load for Bolt Loosening under Transverse Loading

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价