Modeling and Multi-objective Optimization of Laser Cleaning Quality of 7075 Aluminum Alloy

doi:10.3901/JME.2025.03.422

Abstract

Abstract: In the process of laser cleaning, it has become a challenge to coordinate and control parameters to ensure efficient and high-precision cleaning quality due to the numerous energy and motion parameters involved in laser processing. To address these issues, a BOX Behnke design (BBD) response surface experiment is designed with process parameters (laser power, scanning speed, pulse frequency) as optimization variables, and surface roughness, oxygen removal rate, and static contact angle as multi-objective optimization indicators after cleaning. A response surface model and GA-BP neural network model are established. Particularly, a multi-objective sparrow algorithm based on the improvement of the good point set and adaptive normal distribution weights is proposed. Therefore, the problems of poor initial population quality, easy to fall into local optima, low population diversity in the later stages of iteration, and low local development ability have been solved. Furthermore, the model is optimized and the optimal process parameter combination obtained through TOPSIS is as follows: pulse frequency 2.6 kHz, laser power 245 W, and scanning speed 2 900 mm/s. In addition, comparative analysis and process experiments of multiple algorithms are conducted to verify the effectiveness of the algorithms. The results showed that the proposed model and algorithm are applied for optimization. As a result, compared with the original sample, the surface roughness is reduced by 40.26%, the oxygen content is reduced by 96.97%, the static contact angle is increased by 58.32%, and the cleaning quality was significantly improved.

Key words: laser cleaning, aluminium alloy, cleaning quality, process parameters, multi objective optimization

CLC Number:

TG156

WANG Wei, LI Xiaoxu, LIU Weijun, BIAN Hongyou, XING Fei, WANG Jing. Modeling and Multi-objective Optimization of Laser Cleaning Quality of 7075 Aluminum Alloy[J]. Journal of Mechanical Engineering, 2025, 61(3): 422-439.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.2025.03.422

http://www.cjmenet.com.cn/EN/Y2025/V61/I3/422

References

[1] WANG J，TIMOKHINA I，SHARP K，et al. Microstructure and precipitation behaviors of laser clad 7075 aluminium alloy[J]. Surface and Coatings Technology，2022，445:128726.
[2] SU R M，QU Y D，LI R D，et al. Influence of RRA treatment on the microstructure and stress corrosion cracking behavior of the spray-formed 7075 alloy[J]. Materials Science，2015，51:372-380.
[3] IMRAN M，KHAN A R A. Characterization of Al-7075 metal matrix composites:A review[J]. Journal of Materials Research and Technology，2019，8(3):3347-3356.
[4] MIRAMONTES J C，GAONA T C，GARCÍA M E，et al. Corrosion Resistance of aluminum alloy AA2024 with hard anodizing in sulfuric acid-free solution[J]. Materials，2022，15(18):6401.
[5] WANG F，WANG Q，HUANG H，et al. Effects of laser paint stripping on oxide film damage of 2024 aluminium alloy aircraft skin[J]. Optics Express，2021，29(22):35516-35531.
[6] CHEN G X，KWEE T J，TAN K P，et al. Laser cleaning of steel for paint removal[J]. Applied Physics A，2010，101:249-253.
[7] LI Z，XU J，ZHANG D，et al. Nanosecond pulsed laser cleaning of titanium alloy oxide films:Modeling and experiments[J]. Journal of Manufacturing Processes，2022，82:665-677.
[8] LI Z，ZHANG D，SU X，et al. Removal mechanism of surface cleaning on TA15 titanium alloy using nanosecond pulsed laser[J]. Optics & Laser Technology，2021，139:106998.
[9] 李宇强，郭玲玉，蒋平，等.铝合金激光清洗表面形貌变化的实验研究及工艺参数优化[J].中国激光，2021，48(22):161-171. LI Yuqiang，GUO Lingyu，JIANG Ping，et al. Experimental study on surface morphology change and process parameter optimization of aluminum alloy by laser cleaning[J]. Chinese Journal of Lasers，2021，48(22):161-171.
[10] LIN J，WANG C. A study of surface quality and mechanical strength in 5083 aluminum alloy plates using pulsed laser cleaning[J]. Journal of Mechanical Science and Technology，2022，36(10):5223-5229.
[11] ZHU G，WANG S，CHENG W，et al. Corrosion and wear performance of aircraft skin after laser cleaning[J]. Optics & Laser Technology，2020，132:106475.
[12] 杨嘉年，周建忠，孙奇，等. 基于响应面分析的激光除漆工艺参数优化[J]. 激光与光电子学进展，2019，56(23):190-197. YANG Jianian，ZHOU Jianzhong，SUN Qi，et al. Optimization of laser paint removal process parameters based on response surface analysis[J]. Laser & Optoelectronics Progress，2019，56(23):190-197.
[13] YANG S，BAI H，LI C，et al. Numerical simulation and multi-objective parameter optimization of Inconel718 coating laser cladding[J]. Coatings，2022，12(5):708.
[14] LU C，SHI J. Simultaneous consideration of relative density，energy consumption，and build time for selective laser melting of Inconel 718:A multi-objective optimization study on process parameter selection[J]. Journal of Cleaner Production，2022，369:133284.
[15] RONG Y，ZHOU Q，HUANG Y，et al. Multi-objective optimization of laser brazing with the crimping joint using ANN and NSGA-II[J]. The International Journal of Advanced Manufacturing Technology，2016，85: 1239-1247.
[16] MA M，XIONG W，LIAN Y，et al. Modeling and optimization for laser cladding via multi-objective quantum-behaved particle swarm optimization algorithm[J]. Surface and Coatings Technology，2020，381:125129.
[17] LI X，ZHAO J，YE Y，et al. Multi-objective optimization of laser shock peening based on an analytical model[J]. International Journal of Fatigue，2023，172:107640.
[18] PENG S，LI T，ZHAO J，et al. Towards energy and material efficient laser cladding process:Modeling and optimization using a hybrid TS-GEP algorithm and the NSGA-II[J]. Journal of Cleaner Production，2019，227: 58-69.
[19] ACHERJEE B，MISRA D，BOSE D，et al. Prediction of weld strength and seam width for laser transmission welding of thermoplastic using response surface methodology[J]. Optics & Laser Technology，2009，41(8):956-967.
[20] ACHERJEE B，KUAR A S，MITRA S，et al. Experimental investigation on laser transmission welding of PMMA to ABS via response surface modeling[J]. Optics & Laser Technology，2012，44(5):1372-1383.
[21] LIU B，WANG C，MI G，et al. Oxygen content and morphology of laser cleaned 5083 aluminum alloy and its influences on weld porosity[J]. Optics & Laser Technology，2021，140:107031.
[22] ZHANG D，XU J，LI Z，et al. Removal mechanism of blue paint on aluminum alloy substrate during surface cleaning using nanosecond pulsed laser[J]. Optics & Laser Technology，2022，149:107882.
[23] 刘伟军，索英祁，姜兴宇，等.激光清洗过程低碳建模与工艺参数优化[J]. 机械工程学报，2023，59(7):276-294. LIU Weijun，SUO Yingqi，JIANG Xingyu， et al. Low-carbon modeling and process parameter optimization for laser cleaning process[J]. Journal of Mechanical Engineering，2023，59(7):276-294.
[24] SASHANK S，BABU P D，MARIMUTHU P. Experimental studies of laser borided low alloy steel and optimization of parameters using response surface methodology[J]. Surface and Coatings Technology，2019，363:255-264.
[25] SHU L，LI J，WU H，et al. Optimization of multi-track laser-cladding process of titanium alloy based on RSM and NSGA-II algorithm[J]. Coatings，2022，12(9):1301.
[26] BAÑON F，MARTIN S，VAZQUEZ-MARTINEZ J M，et al. Predictive models based on RSM and ANN for roughness and wettability achieved by laser texturing of S275 carbon steel alloy[J]. Optics & Laser Technology，2024，168:109963.
[27] 赵凯，梁旭东，王炜，等. 基于NSGA-Ⅱ算法的同轴送粉激光熔覆工艺多目标优化[J]. 中国激光，2020，47(1):96-105. ZHAO Kai，LIANG Xudong，WANG Wei，et al. Multi-objective optimization of coaxial powder feeding laser cladding based on NSGA-II[J]. Chinese Journal of Lasers，2020，47(1):96-105.
[28] GNANAVELBABU A，ARUNACHALAM V，SUNU SURENDRAN K T，et al. Optimization of CO₂ laser cutting parameters for AA6061/B4C/HBN Hybrid Composites using Taguchi-based response surface methodology[J]. Trends in Manufacturing and Engineering Management:Select Proceedings of ICMechD 2019，2020:111-122.
[29] SONG C，LIU L，YANG Y，et al. Prediction on geometrical characteristics of laser energy deposition based on regression equation and neural network[J]. IFAC-Papers OnLine，2020，53(5):89-96.
[30] DING S，SU C，YU J. An optimizing BP neural network algorithm based on genetic algorithm[J]. Artificial intelligence review，2011，36:153-162.
[31] 石明，汪舟，甘进，等. 基于GA-BP神经网络的喷丸样品表层硬度预测模型[J]. 表面技术，2022，51(1):332-338+357. SHI Ming，WANG Zhou，GAN Jin，et al. Surface hardness prediction model of shot peening sample based on GA-BP neural network[J]. Surface Technology，2022，51(1):332-338+357.
[32] 姜兴宇，刘傲，杨国哲，等. 激光增材制造过程低碳建模与工艺参数优化[J]. 机械工程学报，2022，58(5):223-238. JIANG Xingyu，LIU Ao，YANG Guozhe，et al. Low-carbon modeling and process parameter optimization of laser additive manufacturing process[J]. Journal of Mechanical Engineering，2022，58(5):223-238.
[33] XUE J，SHEN B. A novel swarm intelligence optimization approach:Sparrow search algorithm[J]. Systems Science & Control Engineering，2020，8(1):22-34.
[34] ZHANG G，HU Y，SUN J，et al. An improved genetic algorithm for the flexible job shop scheduling problem with multiple time constraints[J]. Swarm and Evolutionary Computation，2020，54:100664.
[35] 闫少强，杨萍，朱东林，等. 基于佳点集的改进麻雀搜索算法[J]. 北京航空航天大学学报，2023，49(10):2790-2798. YAN Shaoqiang，YANG Ping，ZHU Donglin，et al. Improve the sparrow search algorithm based on good point set[J]. Journal of Beijing university of aeronautics and astronautics，2023，49(10):2790-2798.
[36] DEB K，AGRAWAL S，PRATAP A，et al. A fast elitist non-dominated sorting genetic algorithm for multi-objective optimization:NSGA-II[C]//Parallel Problem Solving from Nature PPSN VI:6th International Conference Paris，France，September 18–20，2000 Proceedings 6. Springer Berlin Heidelberg，2000:849-858.
[37] 毛清华，张强. 融合柯西变异和反向学习的改进麻雀算法[J]. 计算机科学与探索，2021，15(6):1155-1164. MAO Qinghua，ZHANG Qiang. An improved sparrow algorithm based on cauchy mutation and reverse learning[J]. Journal of Computer Science and Exploration，2021，15(6):1155-1164.
[38] DONG X，LIU X. Multi-objective optimization of heat transfer in microchannel for non-Newtonian fluid[J]. Chemical Engineering Journal，2021，412:128594.
[39] 田志强，姜兴宇，杨国哲，等. 一种面向航天复杂构件的柔性作业车间能耗优化调度问题研究[J]. 机械工程学报，2023，59(8):273-287. TIAN Zhiqiang，JIANG Xingyu，YANG Guozhe，et al. Research on energy consumption optimization scheduling of flexible job shop for aerospace complex components[J]. Journal of Mechanical Engineering，2023，59(8):273-287.
[40] 王蔚，李相锦，刘伟军，等. 激光清洗7075铝合金阳极氧化膜的工艺参数对表面质量的影响[J]. 中国激光，2022，49(16):189-203. WANG Wei，LI Xiangjin，LIU Weijun，et al. Effect of process parameters on surface quality of laser cleaning 7075 aluminum alloy anodized film[J]. Chinese Journal of Lasers，2022，49(16):189-203.
[41] KHUBROO M，MOUSAVIRAD S J. A levy flight-based decomposition multi-objective optimization based on grey wolf optimizer[C]//2019 9th International Conference on Computer and Knowledge Engineering (ICCKE). IEEE，2019:155-161.
[42] WANG X，LONG S. Study on hereditary of pores in laser remelting of die casting AZ91D magnesium alloy[J]. Acta Metall Sin，2012，48(12):1437-1445.
[43] WANG A，FENG A，GU X，et al. Effect of picosecond laser cleaning on surface morphology and properties of stainless steel[J]. Optics & Laser Technology，2023，159:109041.
[44] 李岩，章晴云，卢小鹏，等. 微弧氧化工艺参数对镁合金表面水滑石复合膜层耐蚀性的影响[J]. 表面技术，2021，50(8):327-336. LI Yan，ZHANG Qingyun，LU Xiaopeng，et al. Effect of Micro-arc oxidation process parameters on corrosion resistance of hydrotalcite composite coatings on magnesium alloy surface[J]. Surface Technology，2021，50(8):327-336.