Study on the Mechanism and Evolution Process of Chip Formation in Electric Discharge Assisted Cutting

doi:10.3901/JME.2025.19.407

Abstract

Abstract: Electric discharge-assisted cutting technology, an efficient and precise machining method for difficult-to-machine materials such as titanium alloys, significantly reduces cutting loads and enhances machining quality. Despite its advantages, limited research exists on the chip formation process and morphological evolution of titanium alloy chips in electric discharge-assisted cutting. This study combines finite element simulation with experimental methods to address this gap and investigate chip formation processes and morphological characteristics under varying processing conditions in electric discharge-assisted cutting. Results indicate that this technique improves the stress distribution uniformity in the material's removal layer by altering the surface temperature field,effectively reducing cutting force and the degree of chip serration. Compared to traditional cutting, the degree of serration of titanium alloy chips in electric discharge-assisted cutting has decreased from 0.372 to 0.195, and the width of the adiabatic shear band has increased from 1.7 μm to 4.3 μm. This study provides important theoretical support for the material removal mechanism of thermal assisted cutting machining.

Key words: titanium alloy, electric discharge-assisted cutting, chips, cutting mechanism, FEM

CLC Number:

TG661
TG506

LIU Xiangyu, LI Changping, XU Moran, CHEN Jielin, LI Shujian, LI Pengnan. Study on the Mechanism and Evolution Process of Chip Formation in Electric Discharge Assisted Cutting[J]. Journal of Mechanical Engineering, 2025, 61(19): 407-419.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.2025.19.407

http://www.cjmenet.com.cn/EN/Y2025/V61/I19/407

References

[1] RAGHAVENDRA S，SATHYANARAYANA P S，VS T，et al. High speed machining of titanium Ti6Al4V alloy components：Study and optimisation of cutting parameters using RSM[J]. Advances in Materials and Processing Technologies，2022，8(1)：277-290.
[2] AL-ASADI M M，AL-TAMEEMI H A. A review of tribological properties and deposition methods for selected hard protective coatings[J]. Tribology International，2022，176：107919.
[3] LI C，QIU X，YU Z，et al. Novel environmentally friendly manufacturing method for micro-textured cutting tools[J]. International Journal of Precision Engineering and Manufacturing-Green Technology，2021，8：193-204.
[4] ZHAO G，ZHAO B，DING W，et al. Nontraditional energy-assisted mechanical machining of difficult-to-cut materials and components in aerospace community：A comparative analysis[J]. International Journal of Extreme Manufacturing，2024，6(2)：022007.
[5] PANDEY K，DATTA S. Hot machining of difficult-to-cut materials：A review[J]. Materials Today：Proceedings，2021，44：2710-2715.
[6] BIJANZAD A，MUNIR T，ABDULHAMID F. Heat-assisted machining of superalloys：A review[J]. The International Journal of Advanced Manufacturing Technology，2022，118(11)：3531-3557.
[7] KIM J H，KIM E J，LEE C M. A study on the heat affected zone and machining characteristics of difficult-to-cut materials in laser and induction assisted machining[J]. Journal of Manufacturing Processes，2020，57：499-508.
[8] MRUTHUNJAYA M，YOGESHA K B. A review on conventional and thermal assisted machining of titanium based alloy[J]. Materials Today：Proceedings，2021，46：8466-8472.
[9] HA J H，LEE C M. A study on the thermal effect by multi heat sources and machining characteristics of laser and induction assisted milling[J]. Materials，2019，12(7)：1032.
[10] LI C，XU M，YU Z，et al. Electrical discharge-assisted milling for machining titanium alloy[J]. Journal of Materials Processing Technology，2020，285：116785.
[11] CHEN J，LI S，CHEN Y，et al. Mechanical analysis and machinability evaluation of a new EDM-turning hybrid machining process[J]. Journal of Materials Processing Technology，2023，318：118019.
[12] XU M，LI C，KURNIAWAN R，et al. Study on surface integrity of titanium alloy machined by electrical discharge-assisted milling[J]. Journal of Materials Processing Technology，2022，299：117334.
[13] 魏荣，徐默然，李常平，等. 电火花辅助铣削钛合金多能场建模及调控优化研究[J]. 机械工程学报，2024，60(9)：393-409. WEI Rong，XU Moran，LI Changping，et al. Modeling of multi-energy field and regulation optimization for electric discharge assisted milling (EDAM) of titanium alloys[J]. Journal of Mechanical Engineering，2024，60(9)：393-409.
[14] LIU H，ZHANG J，JIANG Y，et al. Investigation on morphological evolution of chips for Ti6Al4V alloys with the increasing milling speed[J]. Procedia CIRP，2016，46：408-411.
[15] UPADHYAY V，JAIN P K，MEHTA N K. Machinability studies in hot machining of Ti-6Al-4V alloy[J]. Advanced Materials Research，2013，622：361-365.
[16] VENKATESAN K，KANUBHAI J，RAVAL G V，et al. A study on prediction of forces and cutting temperature in laser-assisted machining of Inconel 718 alloy using numerical approach[J]. Materials Today：Proceedings，2018，5(5)：12339-12348.
[17] XI Y，BERMINGHAM M，WANG G，et al. SPH/FE modeling of cutting force and chip formation during thermally assisted machining of Ti6Al4V alloy[J]. Computational Materials Science，2014，84：188-197.
[18] LI C，HUANG L，XU M，et al. Processing mechanism of electrical discharge-assisted milling titanium alloy based on 3D thermal-mechanical coupling cutting model[J]. Journal of Manufacturing Processes，2022，78：107-119.
[19] CHEN Y，LI C，LI S，et al. Study on the formation of the crater and modified layer in edm titanium alloys based on fluid–solid coupled temperature field model[J]. International Journal of Precision Engineering and Manufacturing，2023，24(3)：337-351.
[20] SIMA M，ÖZEL T. Modified material constitutive models for serrated chip formation simulations and experimental validation in machining of titanium alloy Ti–6Al–4V[J]. International Journal of Machine Tools and Manufacture，2010，50(11)：943-960.
[21] LIU D，NI C，WANG Y，et al. Review of serrated chip characteristics and formation mechanism from conventional to additively manufactured titanium alloys[J]. Journal of Alloys and Compounds，2023，970：172573.