无碳化物贝氏体钢的滚动接触疲劳磨损行为

doi:10.3901/JME.2018.04.176

机械工程学报 ›› 2018, Vol. 54 ›› Issue (4): 176-185.doi: 10.3901/JME.2018.04.176

无碳化物贝氏体钢的滚动接触疲劳磨损行为

郑春雷^1,2, 张福成^1,2, 吕博³, 但锐¹, 苏丽婷¹

1. 亚稳材料制备技术与科学国家重点实验室秦皇岛 066004;
2. 燕山大学材料科学与工程学院秦皇岛 066004;
3. 燕山大学环境与化学工程学院秦皇岛 066004

收稿日期:2017-02-16 修回日期:2017-11-23 出版日期:2018-02-20 发布日期:2018-02-20
通讯作者: 张福成(通信作者),男,1964年出生,博士,教授,博士研究生导师。主要研究方向为先进钢铁材料。E-mail:zfc@ysu.edu.cn
作者简介:郑春雷,男,1981年出生,实验师。主要研究方向为贝氏体钢的氢脆及疲劳性能。E-mail:zhengclysu@ysu.edu.cn
基金资助:
国家重点研发计划（2017YFB0304501）、河北省自然科学基金（E2018203271）和燕山大学青年教师自主研究计划（15LGB006）资助项目

Rolling Contact Fatigue Wear Behavior of Carbide-free Bainitic Steel

ZHENG Chunlei^1,2, ZHANG Fucheng^1,2, LÜ Bo³, DAN Rui¹, SU Liting¹

1. State Key Laboratory of Metastable Materials Science and Technology, Qinhuangdao 066004;
2. College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004;
3. School of Environmental & Chemical Engineering, Yanshan University, Qinhuangdao 066004

Received:2017-02-16 Revised:2017-11-23 Online:2018-02-20 Published:2018-02-20

摘要/Abstract

摘要： 通过滚动接触疲劳磨损试验和扫描、透射、X射线衍射等分析方法，研究无碳化物贝氏体钢的滚动接触疲劳磨损行为。结果表明，无碳化物贝氏体钢拥有较为理想的滚动接触疲劳磨损性能，其疲劳磨损失效形式为浅层剥落，试样表面产生的严重塑性变形层，有效地阻碍了疲劳裂纹向深处扩展；经过920℃奥氏体化处理40 min，随后350℃盐浴等温30 min比等温100 min处理的试样的滚动接触疲劳磨损性能更加优异，其滚动接触疲劳磨损寿命可达到8.0×10⁶次；残余奥氏体能够有效地提高接触表面硬度，松弛裂纹尖端的应力集中，从而改善滚动接触疲劳磨损性能；在滚动接触疲劳磨损过程中，试样表面的硬度显著的提高，表面合金元素的再分配，对滚动接触疲劳磨损性能的提高有一定的促进作用。

关键词: 残余奥氏体, 滚动接触疲劳磨损, 合金元素, 无碳化物贝氏体钢

Abstract: Rolling contact fatigue wear (RCFW) behavior of a new type carbide-free bainitic steel(CFBS) has been investigated by means of RCFW testing, scanning electron microscope, transmission electron microscopy and X-ray diffraction. The results show that the CFBS exists the satisfactory RCFW performance, the failure mode of fatigue wear of CFBS is shallow spalling. The severe plastic deformation layer produced on the specimen surface can effectively block the fatigue crack toward greater depth. The RCFW behavior is more excellent of the sample which is austenized at 920℃ for 40 min, and immediately austempered in a molten salt bath at a temperature of 350℃ for 30 min than that for 100 min. The RCFW life of the sample of 350℃ for 30 min can reach 8.0×10⁶ cycles. Retained austenite can effectively improve the hardness of the contact surface and relax the stress concentration at the crack tip, and the RCFW behavior is improved. During the RCFW process, the hardness increase in the specimen surface and redistribution of the alloying elements exhibit a positive effect on the improvement of the RCFW behavior.

Key words: alloying element, carbide-free bainitic steel, retained austenite, rolling contact fatigue wear

中图分类号:

TG142

郑春雷, 张福成, 吕博, 但锐, 苏丽婷. 无碳化物贝氏体钢的滚动接触疲劳磨损行为[J]. 机械工程学报, 2018, 54(4): 176-185.

ZHENG Chunlei, ZHANG Fucheng, LÜ Bo, DAN Rui, SU Liting. Rolling Contact Fatigue Wear Behavior of Carbide-free Bainitic Steel[J]. Journal of Mechanical Engineering, 2018, 54(4): 176-185.

参考文献

[1] 金学松, 沈志云. 轮轨滚动接触疲劳问题研究的最新进展[J]. 铁道学报, 2001, 23(2):92-108. JIN Xuesong, SHEN Zhiyun. Rolling contact fatigue of wheel/rail and its advanced research progress[J]. Journal of China Railway Society, 2001, 23(2), 92-108.
[2] ZHANG Fucheng, ZHENG Chunlei, LÜ Bo, et al. Effects of hydrogen on the properties of bainitic steel crossing[J]. Engineering Failure Analysis, 2009, 16:1461-1467.
[3] 乔桂英, 唐雷, 张文雷, 等. 铁素体/贝氏体双相X80管线钢疲劳性能研究[J]. 燕山大学报, 2015, 39(6):502-505. QIAO Guiying, TANG Lei, ZHANG Wenlei, et al. Study on fatigue property of ferrite/bainite duple phases X80 pipeline steel[J]. Journal of Yanshan University, 2015, 39(6):502-505.
[4] ZHENG C L, DAN R, ZHANG F C, et al. Effects of retained austenite and hydrogen on the rolling contact fatigue behaviours of carbide-free bainitic steel[J]. Materials Science and Engineering A, 2014, 594:364-671.
[5] 江晓禹, 金学松, 轮轨间的液态介质和表面微观粗糙度对接触表面疲劳损伤的影响[J]. 机械工程学报, 2004, 40(8):18-23. JIANG Xiaoyu, JIN Xuejun, Influence of liquid and micro-roughness between wheel and rail on the fatigue damage of contact surface[J]. Journal of Mechanical Engineering, 2004, 40(8):18-23.
[6] 张福成. 高锰钢辙叉材料研究进展[J]. 燕山大学学报, 2010, 34(3):189-193. ZHANG Fucheng. Reaearch progress of high manganese steel crossing materials[J]. Journal of Yanshan University, 2010, 34(3):189-193.
[7] 张福成, 杨志南, 康杰. 铁路辙叉用贝氏体钢研究进展[J]. 燕山大学学报, 2013, 37(1):1-7. ZHANG Fucheng, YANG Zhinan, KANG Jie. Research progress of bainitic steel used for railway crossing[J]. Journal of Yanshan University, 2013, 37(1):1-7.
[8] 曾东方, 鲁连涛, 张远彬, 等. 高速轮轨材料匹配的滚动接触磨损性能[J]. 机械工程学报, 2013, 49(13):183-189. ZENG Dongfang, LU Liantao, ZHANG Yuanbin, et al. Rolling contact wear properties of matching of high-speed wheel/rail materials[J]. Journal of Mechanical Engineering, 2013, 49(13):183-189.
[9] 曾东方, 鲁连涛, 张远彬, 等. 合金含量对高速车轮材料滚动接触磨损性能的影响[J]. 摩擦学学报, 2012, 32(6):599-605. ZENG Dongfang, LU Liantao, ZHANG Yuanbin, et al. Effect of alloy content on rolling contact wear of high-speed wheel material[J]. Tribology, 2012, 32(6):599-605.
[10] 肖俊华, 段晓森. 贝氏体钢组合辙叉的准静态接触有限元分析[J]. 燕山大学学报, 2015, 39(2):165-169. XIAO Junhua, DUAN Xiaosen. Finite element analysis on bainite steel crossing under quasi-static contact load[J]. Journal of Yanshan University, 2015, 39(2):165-169.
[11] YOKOYAMA H, MITAO S, YAMAMOTO S, et al. Effect of the angle of attack on flaking behavior in pearlitic and bainitic steel rails[J]. Wear, 2002, 253(1-2):60-66.
[12] CHANG L C. The rolling/sliding wear performance of high silicon carbide-free bainitic steels[J]. Wear, 2005, 258:730-743.
[13] CARROLL R I, BEYNON J H. Rolling contact fatigue of white etching layer:part 1 crack morphlolgy[J].Wear, 2007, 262:1253-1266.
[14] ZHENG C L, LÜ B, CHEN C, et al. Hydrogen embrittlement of a manganese-aluminum high-strength bainitic steel for railway crossings[J]. ISIJ International, 2011, 51(10):1749-1753.
[15] SOLANO-ALVAREZ W., PICKERING E J, BHADESHIA H K D H. Degradation of nanostructured bainitic steel under rolling contact fatigue[J]. Materials Science and Engineering A, 2014, 617:156-164.
[16] 曹栋, 康杰, 龙晓燕, 等. 辙叉用贝氏体钢热处理工艺研究[J]. 机械工程学报, 2014, 50(4):47-52. CAO Dong, KANG Jie, LONG Xiaoyan, et al. Research on heat treatment of bainitic steel crossing[J]. Journal of Mechanical Engineering, 2014, 50(4):47-52.
[17] WEI D Y, GU J L, FANG H S, et al. Fatigue behavior of 1500 MPa bainite/martensite duplex-phase high strength steel[J]. International Journal of Fatigue, 2004, 26(4):437-442.
[18] LEIRO A, ROSHAN A, SUNDIN K G, et al. Fatigue of 0.55C-1.72Si steel with tempered martensitic and carbide-free bainitic microstructures[J]. Acta Metallurgica Sinica (English Letters), 2014, 27(1):55-62.
[19] SHEN Y, MOGHADAM S M, SADEGHI F, et al. Effect of retained austenite-compressive residual stresses on rolling contact fatigue life of carburized AISI 8620 steel[J]. International Journal of Fatigue, 2015, 75:135-144.
[20] ZHAO P, ZHANG B, CHENG C, et al. The significance of ultrafine film-like retained austenite in governing very high cycle fatigue behavior in an ultrahigh-strength Mn-Si-Cr-C steel[J]. Materials Science and Engineering A, 2015, 645:116-121.
[21] ZHENG C L, LÜ B, ZHANG F C, et al. Effect of secondary cracks on hydrogen embrittlement of bainitic steels[J]. Materials Science and Engineering A, 2012, 547:99-103.
[22] 但锐, 张明, 郑春雷, 等. 氢对贝氏体辙叉钢摩擦磨损行为的影响[J]. 机械工程学报, 2012, 48(20):33-38. DAN Rui, ZHANG Ming, ZHENG Chunlei, et al. Effects of hydrogen on wear behacior of bainitic steel used for crossing[J]. Journal of Mechanical Engineering, 2012, 48(20):33-38.
[23] DYSON D J, HOLMES B. Effect of alloying additions on the lattice parameter of austenite[J]. Journal of Iron and Steel Institute, 1970, 208:469-474.
[24] 韩玉梅, 韩恩厚, 柯伟, 多级载荷作用下的疲劳寿命可靠性计算方法[J]. 金属学报, 1994, 30(4):171-175. HAN Yunmei, HAN Enhou, KE Wei, Determination of fatigue reliability under complex loading[J]. Acta Metallurgic Sinica, 1994, 30(4):171-175.
[25] NAGUMO M, ISHIKAWA T, EEDOH T, et al. Amorphization associated with crack propagation in hydrogen-charged steel[J]. Scripta. Materialia, 2003, 49(9):837-842.
[26] BHADESHIA H K D H. Steels for bearings[J]. Progress in Materials Science, 2012, 57(2):268-435.
[27] TAGA Y, ISOGAI A, NAKAJIMA K. Role of alloying elements in the friction and wear of copper alloys[J]. Wear, 1977, 44(2):377-391.
[28] GANSHEIMER J, HOLINSKI R. Molybdenum disulfide in oils and greases under boundary conditions[J]. Journal of Lubrication Technology, 1973, 95(2):242-246.
[29] 马党参, 迟宏宵, 雍岐龙, 等. 铝对Cr8WMo2V2SiNb冷作模具钢组织及力学性能的影响[J]. 钢铁, 2010, 45(6):79-83. MA Dangshen, CHI Hongxiao, YONG Qilong, et al. Effect of aluminum on microstructure and mechanical properties of Cr8WMo2V2SiNb steel[J]. Iron and Steel, 2010, 45(6):79-83.
[30] 程巨强, 康沫狂. 硅对准贝氏体渗碳钢组织与性能的影响[J]. 材料热处理学报, 2003, 24(3):8-11. CHENG Juqiang, KANG Mokuang. Effect of silicon on the microstructure and properties of meta-bainitic carburizing steel[J]. Transactions Materials and Heat Treatment, 2003, 24(3):8-11.
[31] 赵佳莉, 杨志南, 张福成. 70Si3Mn钢中无碳化物贝氏体组织及其性能研究[J]. 燕山大学学报, 2015, 39(3):199-205. ZHAO Jiali, YANG Zhinan, ZHANG Fucheng. Study on carbide-free bainite microstructure and mechanical properties of 70Si3Mn steel[J]. Journal of Yanshan University, 2015, 39(3):199-205.
[32] 任勇强, 尚成嘉, 张宏伟, 等. 0.23C-1.9Mn-1.6Si钢中的残余奥氏体对韧塑性的影响[J]. 材料研究学报, 2014, 28(4):274-280. REN Yongqiang, SHANG Chengjia, ZHANG Hongwei, et al. Effect of retained austenite on toughness and plasticity of 0.23C-1.9Mn-1.6Si steel[J]. Chinese journal of Materials Research, 2014, 28(4):274-280.
[33] ZHENG Chunlei, LÜ Bo, ZHANG Fucheng, et al. A novel microstructure of carbide-free bainitic medium carbon steel observed during rolling contact fatigue[J]. Scripta Material, 2016, 114:13-16.
[34] ABARESHI M, EMADODDIN E. Effect of retained austenite characteristics on fatigue behavior and tensile properties of transformation induced plasticity steel[J]. Materials and Design, 2011, 32(10):5099-5105.
[35] HUO C Y, GAO H L. Strain-induced martensitic transformation in fatigue crack tip zone for a high strength steel[J]. Materials Characterzation, 2005, 55(1):12-18.

无碳化物贝氏体钢的滚动接触疲劳磨损行为

Rolling Contact Fatigue Wear Behavior of Carbide-free Bainitic Steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	林利, 梁文, 朱国明, 李宝顺, 康永林, 刘仁东. Q&P工艺对1 800 MPa新型热成形钢微观组织和力学性能的影响[J]. 机械工程学报, 2019, 55(10): 77-85.
[2]	罗来马, 黄科, 昝祥, 朱晓勇, 李萍, 吴玉程. 合金化改性钨基材料的组织和性能研究与发展[J]. 机械工程学报, 2018, 54(8): 117-128.
[3]	黄涛, 陈小平, 王向东, 汪兵, 王帆, 李向阳. 高强耐候钢在NaCl溶液中的腐蚀锈层特征和耐腐蚀性研究[J]. 机械工程学报, 2017, 53(20): 45-53.
[4]	彭杏娜, 彭云, 彭先宽, 丛相州. 多层多道TIG焊对高强钢焊缝组织和韧性的影响[J]. 机械工程学报, 2017, 53(18): 106-112.
[5]	朱国明, 康永林, 朱帅. 汽车用超高强QP钢的工艺与组织性能研究[J]. 机械工程学报, 2017, 53(12): 110-117.
[6]	吴化;姜颖;尤申申;韩英;刘云旭. 超级贝氏体组织中残余奥氏体的TRIP效应研究[J]. , 2014, 50(22): 69-75.
[7]	张宇光;赵爱民;赵征志;唐荻. 冷轧TRIP钢中残余奥氏体的热稳定性[J]. , 2011, 47(4): 66-70.
[8]	屈岳波;黄欣泉;曹彬;蔡志鹏;潘际銮. 残余奥氏体对2.25Cr-1Mo钢焊缝冲击性能的影响[J]. , 2011, 47(14): 44-48.
[9]	吴红艳;杜林秀;刘相华;王国栋;董俊华;董杰. 变形条件对Mn-Cu耐候钢连续冷却相变的影响[J]. , 2007, 43(9): 145-150.
[10]	孙淑华;张振戎;熊毅;吕知清;厉勇;傅万堂;牧正志. 锰和硅添加对重度冷轧及退火后珠光体钢力学性能的影响[J]. , 2005, 41(5): 147-153.
[11]	刘贵立;张国英;曾梅光;钱存富. Co、Al对二次硬化钢微结构影响的穆谱研究[J]. , 2002, 38(12): 149-152.
[12]	崔占全. 碳质量分数0.70%的降碳、硅合金化冷轧工作辊材料[J]. , 2000, 36(1): 110-112.
[13]	孙大涌;薛侃时;徐佐仁;王滨;张静江;李晋. 锰低温钢中锰及合金元素的不平衡偏聚[J]. , 1998, 34(4): 1-6，14.
[14]	任登义;魏星;陈立宗. 冷轧工作辊局部冷焊焊缝中残余奥氏体对抗疲劳性的影响[J]. , 1998, 34(3): 90-95.
[15]	仝健民;张伟良. 高铬铸铁中残余奥氏体对冲击疲劳磨损的影响[J]. , 1994, 30(6): 103-107.