Q&P工艺对1 800 MPa新型热成形钢微观组织和力学性能的影响

doi:10.3901/JME.2019.10.077

机械工程学报 ›› 2019, Vol. 55 ›› Issue (10): 77-85.doi: 10.3901/JME.2019.10.077

Q&P工艺对1 800 MPa新型热成形钢微观组织和力学性能的影响

林利^1,2, 梁文¹, 朱国明¹, 李宝顺¹, 康永林¹, 刘仁东²

1. 北京科技大学材料科学与工程学院北京 100083;
2. 鞍钢集团钢铁研究院鞍山 114009

收稿日期:2018-07-25 修回日期:2018-12-25 出版日期:2019-05-20 发布日期:2019-05-20
通讯作者: 朱国明(通信作者),男,1974年出生,博士,副教授。主要从事于材料加工过程数值模拟及应用;先进汽车用金属材料的开发、制备及应用。E-mail:zhuguoming@ustb.edu.cn
作者简介:林利,男,1981年出生,博士研究生。主要从事汽车用钢产品开发和应用技术研究。E-mail:ag_linli@126.com
基金资助:
国家自然科学基金（U1460101）和高等学校博士学科点专项科研基金（20120006120002）资助项目

Influence of Quenching and Partitioning Process on Microstructure and Mechanical Properties of a Novel 1 800 MPa Hot Stamping Steel

LIN Li^1,2, LIANG Wen¹, ZHU Guoming¹, LI Baoshun¹, KANG Yonglin¹, LIU Rendong²

1. School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083;
2. Iron and Steel Reseorrch Insitute, Ansteel Group, Anshan 114009

Received:2018-07-25 Revised:2018-12-25 Online:2019-05-20 Published:2019-05-20

摘要/Abstract

摘要： 现阶段热冲压成形钢一直存在塑性差、冲击韧性低、弯曲吸能有限等潜在问题，需要采用一些新兴的技术来提高其塑韧性，使其更好地服役于车身轻量化。采用盐浴的方式对1 800 MPa新型热冲压成形钢进行一步Q&P热处理，研究淬火温度、配分时间和配分温度对热冲压成形钢微观组织和力学性能的影响，并通过XRD，EBSD研究残余奥氏体的含量与分布以及残余奥氏体的含碳量，得到最佳热处理工艺参数。研究结果表明：当配分温度一定时，随着配分时间的延长，试样的抗拉强度和屈服强度呈现下降趋势，而伸长率呈现增加的趋势。在230℃配分30 s时，试验钢的综合力学性能达到最佳，其抗拉强度、伸长率和强塑积分别达到2 034 MPa、10.2%和20 747 MPa·%；相比直接淬火分别提高9.5%、73.5%和90.0%。在保持超高强度的同时，塑韧性得到显著提高，满足汽车用钢要求，能够更好地服役于汽车轻量化制造。

关键词: 二维库伦摩擦力系统, 拐点, 滑移/粘滞转换, 解析解, 路径坐标系, 数值算法, P工艺, Q&, 残余奥氏体, 力学性能, 热成形钢

Abstract: At present, hot stamping forming steel has some potential problems, such as poor plasticity, low impact toughness, limited bending energy absorption, which need to be sloved by some new technologies to make it serve the automobile lightweigh better. So microstructure and mechanical properties of a novel 1 800 MPa hot stamping steel carried out one step method quenching and partitioning process are investigated. Quenching temperature, partitioning temperature and partitioning time are controlled by salt bath. What's more, the content and distribution of retained austenite are observed via XRD and EBSD and carbon content in retained austenite is calculated. It is found that when the partitioning temperature is constant, the tensile strength and yield strength of the specimens decrease with the increase of the partitioning time, while the elongation increases, and when the partitioning temperature and the partitioning time are 230℃and 30 s respectively, the comprehensive mechanical properties of the experimental steel are best, the tensile strength is up to 2 034 MPa, while the elongation is up to 10.2%, and the production of tensile strength and plasticity is 20 747 MPa·%. Compared to the direct quenching, the tensile strength, elongation and production of them are increased by 9.5%, 73.5%, and 90%, respectively. This is that the plasticity and toughness have been significantly improved to meet the requirements of automotive steel, while maintaining ultrahigh strength, and this steel can better serve in automotive lightweight manufacturing.

Key words: Analytical Solutions, Slip/Stick Transition, Two-Dimensional Coulomb Frictional System, Numerical Algorithm, Path Coordinated System, Sharp Bending Corner, hot stomping steel, mechanical properties, Q&P process, retained austenite

中图分类号:

TG156

林利, 梁文, 朱国明, 李宝顺, 康永林, 刘仁东. Q&P工艺对1 800 MPa新型热成形钢微观组织和力学性能的影响[J]. 机械工程学报, 2019, 55(10): 77-85.

LIN Li, LIANG Wen, ZHU Guoming, LI Baoshun, KANG Yonglin, LIU Rendong. Influence of Quenching and Partitioning Process on Microstructure and Mechanical Properties of a Novel 1 800 MPa Hot Stamping Steel[J]. Journal of Mechanical Engineering, 2019, 55(10): 77-85.

参考文献

[1] 中华人民共和国工业和信息化部. 2017年汽车工业经济运行情况[EB/OL].[2018-01-12]. http://www.miit.gov.cn/n1146312/n1146904/n1648362/n1648363/c6011922/content.html. Ministry of Industry and Information Technology of People's Republic of China.Economic Operation of Automobile Industry in 2017[EB/OL].[2018-01-12]. http://www.miit.gov.cn/n1146312/n1146904/n1648362/n1648363/c6011922/content.html.
[2] 唐见茂. 新能源汽车轻量化材料[J]. 新型工业化,2016,6(1):1-14. TANG Jianmao. Lightweight materials for new energy vehicles[J]. The Journal of New Industrialization,2016,6(1):1-14.
[3] LIN Li,LI Baoshun,ZHU Guoming,et al. Effect of niobium precipitation behavior on microstructure and hydrogen induced cracking of press hardening steel 22MnB5[J]. Materials Science & Engineering A,2018,721(4):38-46.
[4] 郝亮,朱国明,闻玉辉,等. 超高强度硼钢38MnB5的热冲压工艺研究[J]. 中南大学学报,2018,49(4):817-823. HAO Liang,ZHU Guoming,WEN Yuhui,et al. Study on hot stamping process of 38MnB5 ultra high strength boron steel[J]. Journal of Central South University,2018,49(4):817-823.
[5] TAYLOR T,CLOUGH A. Critical review of automotive hot-stamped sheet steel from an industrial perspective[J]. Materials Science & Technology,2018,37(7):809-861.
[6] WEN Yuhui,ZHU Guoming,DAI Siyu,et al. Effect of Ti on microstructure and strengthening behavior in press hardening steels[J]. Journal of Central South University,2017,24(10):2215-2221.
[7] SPEER J,MATLOCK D K,COOMAN B C D,et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia,2003,51(9):2611-2622.
[8] 李小琳,王昭东. 一步Q&P工艺对双马氏体钢微观组织与力学性能的影响[J]. 金属学报,2015,51(5):537-544. LI Xiaolin,WANG Zhaodong. Effect of one step Q&P process on microsturcture and mechanical properties of a dualmartensite steel[J]. Acta Metallurgica Sinica,2015,51(5):537-544.
[9] LARS O W,FLORIAN N,DMYTRO R,et al. 1-step quenching and partitioningof the press-hardening steel 22MnB5[J]. Steel Research International,2016,87:1-14.
[10] LIU Li,HE Binbin,CHENG Guanju,et al. Optimum properties of quenching and partitioning steels achieved by balancing fraction and stability of retained austenite[J]. Scripta Materialia,2018,150(6):1-6.
[11] PIERCE D T,COUGHLIN D R,CLARKE K D,et al. Microstructural evolution during quenching and partitioning of 0.2C-1.5Mn-1.3Si steels with Cr or Ni additions[J]. Acta Materialia,2018,151(6):454-469.
[12] 徐祖耀. 淬火-碳分配-回火(Q-P-T)工艺浅介[J]. 金属热处理,2009,34(6):1-8. XU Zuyao. A brief introduction to quenching partitioning tempering(Q-P-T) process[J]. Heat Treatment of Metals,2009,34(6):1-8.
[13] 徐祖耀. 马氏体相变与马氏体[M]. 2版. 北京:科学出版社,1999. XU Zuyao. Martensitic transformation and martensite.[M]. 2nd ed. Beijing:Science Press,1999.
[14] NISHIYAMA Z. Martensite transformation[M]. Tokyo:Maruzen,1979.
[15] PENG Fei,XU Yunbo,GU Xingli,et al. The relationships of microstructure-mechanical properties in quenching and partitioning (Q&P) steel accompanied with microalloyed carbide precipitation[J]. Materials Science & Engineering A,2018,723(18):247-258.

Q&P工艺对1 800 MPa新型热成形钢微观组织和力学性能的影响

Influence of Quenching and Partitioning Process on Microstructure and Mechanical Properties of a Novel 1 800 MPa Hot Stamping Steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	窦炜, 崔岗卫, 袁胜万, 何晓聪. 基于摆线刀齿轨迹的未变形铣屑厚度分析[J]. 机械工程学报, 2019, 55(7): 234-242.
[2]	于明润, 赵洪运, 蒋智华, 周利, 黄永宪, 宋晓国. 铝/黄铜异种金属搅拌摩擦焊搭接接头显微组织与力学性能[J]. 机械工程学报, 2019, 55(6): 39-45.
[3]	孙明翰, 杨玉青, 朱志旺, 魏洁平, 杜凤山. 20CrMn钢双辊薄带振动铸轧细晶机理试验[J]. 机械工程学报, 2019, 55(4): 54-59.
[4]	杨建伟, 刘传, 王金海, 孙冉, 祝赫锴. 牵引与桥梁上拱激励下城轨列车动力学性能研究[J]. 机械工程学报, 2019, 55(4): 118-125.
[5]	王明杰. 一种模拟断路器负荷的装置设计与研究[J]. 电气工程学报, 2019, 14(2): 38-42.
[6]	杨玉维, 李彬, 周海波, 赵新华, 宋阳, 刘凉, 赵磊. 计及非完美运动副的移动并联机械手动力学分析[J]. 机械工程学报, 2019, 55(15): 208-216.
[7]	周橙, 池茂儒, 梁树林, 王湘涛, 周飞, 吴兴文. 城市轻轨车辆带摇枕转向架的结构方案设计和动力学性能[J]. 机械工程学报, 2019, 55(14): 88-95.
[8]	黄华贵, 赵阳, 王超, 燕猛. 界面涂层对厚规格热轧钢/铝复合板界面结构与力学性能的影响[J]. 机械工程学报, 2019, 55(14): 30-36.
[9]	曹健, 贺宗晶, 亓钧雷, 王厚勤, 冯吉才. 采用(Ti/Ni/Cu)_f多层箔钎焊C/C复合材料与TiAl合金[J]. 机械工程学报, 2018, 54(9): 108-114.
[10]	庞生洋, 胡成龙, 杨鸷, 汤素芳. 预制体结构对C/C复合材料力学性能、断裂行为以及热物性能的影响[J]. 机械工程学报, 2018, 54(9): 97-107.
[11]	万震宇, 周霞, 张昭. 6005-T6铝合金搅拌摩擦焊接微观组织演变计算及力学性能预测[J]. 机械工程学报, 2018, 54(8): 129-136.
[12]	陈夏明, 王晓南, 孙茜, 张敏, 陈长军, 邸洪双. Al-Si镀层对22MnB5钢激光焊接接头组织和性能的影响[J]. 机械工程学报, 2018, 54(6): 162-167.
[13]	郑春雷, 张福成, 吕博, 但锐, 苏丽婷. 无碳化物贝氏体钢的滚动接触疲劳磨损行为[J]. 机械工程学报, 2018, 54(4): 176-185.
[14]	王波, 张洪涛, 朱训明, 王云峰, 金伟, 何鹏. 铝-铜层状复合材料热辅助超声波増材制造方法[J]. 机械工程学报, 2018, 54(22): 95-102.
[15]	刘净川, 姜风春, 王立权, 张蒙祺, 运飞宏. Ti-(SiC_f/Al₃Ti)层状复合材料在侵彻早期阶段基于NEIM的建模与仿真研究[J]. 机械工程学报, 2018, 54(22): 63-77.