长贮环境下高频电连接器接触性能退化规律的研究

doi:10.3901/JME.2025.14.344

机械工程学报 ›› 2025, Vol. 61 ›› Issue (14): 344-351.doi: 10.3901/JME.2025.14.344

• 交叉与前沿 • 上一篇

扫码分享

长贮环境下高频电连接器接触性能退化规律的研究

陈文华, 杨定, 陈哲文, 方英春, 钟立强

浙江理工大学机电产品可靠性分析与测试国家地方联合工程研究中心杭州 310018

收稿日期:2024-06-22 修回日期:2025-01-17 发布日期:2025-08-25
作者简介:陈文华，男，1963年出生，博士，教授，博士研究生导师。主要研究方向为可靠性设计、试验及统计分析。E-mail:chenwh@zstu.edu.cn;钟立强(通信作者)，男，1989年出生，博士，讲师。主要研究方向为电连接器接触可靠性、产品性能退化建模、加速寿命试验和加速退化试验。E-mail:zlq001@zstu.edu.cn
基金资助:
国家自然科学基金资助项目(2021C01133)。

Research on Degradation Law of Contact Performance for High-frequency Electrical Connectors in Long-term Storage Environment

CHEN Wenhua, YANG Ding, CHEN Zhewen, FANG Yingchun, ZHONG Liqiang

National and Local Joint Engineering Research Center of Reliability Analysis and Testing for Mechanical and Electrical Products, Zhejiang Sci-Tech University, Hangzhou 310018

Received:2024-06-22 Revised:2025-01-17 Published:2025-08-25

摘要/Abstract

摘要： 高频电连接器是型号系统中用于实现高频信号传输的基础元件，其接触性能的退化会造成信号衰减和反射等问题。以J599型高频电连接器为研究对象，分析接触件表面接触状态，建立插入损耗计算方法。考虑温度的影响，分析高频电连接器在贮存环境条件下的接触件表面氧化腐蚀物的增长规律，建立接触对的插入损耗退化轨迹模型。以温度为加速应力开展J599型高频电连接器的加速退化试验，结果表明，提高温度可加快接触性能退化，不同应力水平下的接触退化趋势与轨迹模型预测结果一致。建立基于阿伦尼斯模型的双加速方程，外推得到正常贮存环境下的接触性能退化趋势，可用于指导高频电连接器的可靠性设计、评估和使用维护。

关键词: 高频电连接器, 贮存环境, 性能退化模型, 插入损耗

Abstract: High frequency electrical connector is the key component for high frequency signal transmission in weapon equipment system. The degradation of contact performance will cause signal attenuation and reflection. Taking J599 high frequency electrical connector as the research object, the surface state of the contact is analyzed, and the insertion loss calculation method is established. Considering the influence of temperature, the growth law of oxidation corrosion substances in the contact of high frequency electrical connector under the storage environment is analyzed, and the insertion loss degradation trend model of the contact pair is established. The accelerated degradation test of J599 high frequency electrical connector is carried out with temperature as the accelerated stress. The results show that the contact degradation can be accelerated by increasing the temperature, and the contact degradation trend under different stress levels is consistent with the model. The double acceleration equation based on Arrhenius model is established, and the degradation trend of contact performance under normal storage environment is extrapolated, which can be used to guide the reliability design, evaluation, use and maintenance of high frequency electrical connectors.

Key words: high frequency electrical connector, storage environment, performance degradation model, insertion loss

中图分类号:

TB114

陈文华, 杨定, 陈哲文, 方英春, 钟立强. 长贮环境下高频电连接器接触性能退化规律的研究[J]. 机械工程学报, 2025, 61(14): 344-351.

CHEN Wenhua, YANG Ding, CHEN Zhewen, FANG Yingchun, ZHONG Liqiang. Research on Degradation Law of Contact Performance for High-frequency Electrical Connectors in Long-term Storage Environment[J]. Journal of Mechanical Engineering, 2025, 61(14): 344-351.

参考文献

[1] LUNDQUIST E J，FURSE C. Connector impedance and frequency modes in aerospace wiring systems[J]. Microwave and Optical Technology Letters，2017，59(1):89-93.
[2] JIN Q，GAO J，FLOWERS G T，et al. Modeling of passive intermodulation with electrical contacts in coaxial connectors[J]. IEEE Transactions on Microwave Theory and Techniques，2018，66(9):4007-4016.
[3] JIN Q，GAO J，BI L，et al. The impact of contact pressure on passive intermodulation in coaxial connectors[J]. IEEE Microwave and Wireless Components Letters，2020，30(2):177-180.
[4] CHEN X，HE Y，YU M P，et al. Empirical modeling of contact intermodulation effect on coaxial connectors[J]. IEEE Transactions on Instrumentation and Measurement，2020，69(7):5091-5099.
[5] CHEN X，HE Y，YANG S，et al. Analytic passive intermodulation behavior on the coaxial connector using Monte Carlo approximation[J]. IEEE Transactions on Electromagnetic Compatibility，2018，60(5):1207- 1214.
[6] ZHU J，GAO J，XIE G，et al. FEM analysis of the impact of coaxial connector on high speed signal transmission[C]// 2007 International Symposium on Communications and Information Technologies. Sydney:IEEE，2007:116-120.
[7] TIMSIT R S. Electrical conduction through small contact spots[J]. IEEE Transactions on Components & Packaging Technologies，2006，29:727-734.
[8] TIMSIT R S. High speed electronic connectors:A review of electrical contact properties[J]. IEICE Transactions on Electronics，2005，88(8):1791-1798.
[9] TIMSIT，R. S. Constriction resistance of thin film contacts[J]. IEEE Transactions on Components & Packaging Technologies，2010，33(3):636-642.
[10] ZHANG G，SHI Y，HE X，et al. The effect of corrosion on the electrical contact performance of aviation connectors revealed by in situ impedance measurements[J]. IEEE Transactions on Components，Packaging and Manufacturing Technology，2025(1):140-149.
[11] 钟立强，陈文华，钱萍，等. 贮存剖面下电连接器接触性能退化统计建模研究[J]. 机械工程学报，2018，54(24):211-219. ZHONG Liqiang，CHEN Wenhua，QIAN pin，et al. Statistical modeling of contact performance degradation of the electrical connectors under the storage profile[J]. Journal of Mechanical Engineering，2018，54(24):197-205.
[12] ZHONG L，FAN X，HAN K，et al. A degradation model for separable electrical contacts based on the failure caused by surface oxide film[J]. Microelectronics Reliability，2022，139:114832.
[13] SHUKLA A，MARTIN R，PROBST R，et al. Comparison of different statistical methods for prediction of lifetime of electrical connectors with short term tests[J]. Microelectronics Reliability，2023，150:115216.
[14] WANG J，FENG Y，CAI M，et al. Electrical contact resistance evolution and interface fretting wear characteristics of conductor-parallel groove clamp system response to breeze vibration environment[J]. IEEE Transactions on Components，Packaging and Manufacturing Technology，2024，14(1):43-51.
[15] LIU X，HU S，XIAO Q，et al. An investigation of the electrical contact failure of JPT electric connectors used in automobiles under multiple stresses[J]. Wear，2024，552-553:205458.
[16] 骆燕燕，刘昙，张兆攀，等. 电连接器接触件的性能退化规律与寿命预测[J]. 兵器装备工程学报，2022，43(9):39-47. LUO Yanyan，LIU Tan，ZHANG Zhaopan，et al. Performance degradation law and life prediction of electrical connector contacts[J]. Journal of Ordnance Equipment Engineering，2022，43(9):39-47.
[17] 骆燕燕，陈月港，王永鹏，等. 随机振动下电连接器微动磨损试验与性能退化模型[J]. 兵器装备工程学报，2024，45(8):34-44. LUO Yanyan，CHEN Yuegang，WANG Yongpeng，et al. Research on performance degradation model of electrical connectors for fretting wear under random vibration[J]. Journal of Ordnance Equipment Engineering，2024，45(8):34-44.
[18] HALL S，HECK H. Advanced signal integrity for high-speed digital designs[M]. New Jersey:John Wiley & Sons，2009.
[19] SHEN Q，LÜ K，LIU G，et al. Impact of electrical contact resistance on the high-speed transmission and on-line diagnosis of electrical connector intermittent faults[J]. IEEE Access，2017，5:4221-4232.
[20] 纪锐. 射频连接器电接触失效机理及其对传输信号影响的研究[D]. 北京:北京邮电大学，2018. JI Rui. Research on the failure mechanism of radio frequency connector and its effects on signal transmission[D]. Beijing:Beijing University of Posts and Telecommunications，2018.
[21] NELSON W B. Accelerated testing:Statistical models，test plans，and data analysis[M]. Toronto:John Wiley & Sons，2004.

长贮环境下高频电连接器接触性能退化规律的研究

Research on Degradation Law of Contact Performance for High-frequency Electrical Connectors in Long-term Storage Environment

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	钱萍, 刘鑫雨, 陈文华, 王哲, 郭明达. 电连接器用聚氨酯胶密封件贮存可靠性建模[J]. 机械工程学报, 2024, 60(20): 361-371.
[2]	杨小玉, 谢里阳, 杨奕凤, 赵丙峰. 三参数威布尔形状参数估计方法的比较与推荐取值[J]. 机械工程学报, 2024, 60(16): 367-376.
[3]	郝鹏, 杨浩, 陈发鑫, 曾耀祥, 王明杰, 王博. 考虑载荷及强度不确定性的结构安全系数精细化设计方法[J]. 机械工程学报, 2024, 60(13): 182-192.
[4]	付玲, 佘玲娟, 颜镀镭, 张鹏, 龙湘云. 基于内嵌物理信息与注意力机制BiLSTM神经网络的臂架系统疲劳损伤预测模型[J]. 机械工程学报, 2024, 60(13): 205-215.
[5]	程洪鑫, 李璐祎, 周长聪. 基于Kriging模型和代理抽样的分布参数不确定性灵敏度分析方法[J]. 机械工程学报, 2024, 60(8): 370-383.
[6]	韦新鹏, 姚中洋, 宝文礼, 张哲, 姜潮. 一种基于主动学习克里金模型的证据理论可靠性分析方法[J]. 机械工程学报, 2024, 60(2): 356-368.
[7]	王瑞雪, 王慧妍, 薛爽, 贺建芸, 陈茜, 张庆, 谢鹏程, 杨卫民, 谭俊. 管状工件内表面铬基薄膜沉积技术研究进展[J]. 机械工程学报, 2023, 59(24): 56-71.
[8]	孔雪峰, 潘骏, 钱萍, 魏义敏, 陈文华. 机械产品多变量相依退化建模方法研究综述[J]. 机械工程学报, 2023, 59(20): 470-488.
[9]	周金宇, 王志凌, 程锦翔, 韩文钦. 面向离散化临界状态空间的重要抽样法[J]. 机械工程学报, 2023, 59(14): 352-360.
[10]	蒋仁言. 两类高度截尾数据及其参数估计问题[J]. 机械工程学报, 2023, 59(10): 374-382.
[11]	陈克强, 姜兴宇, 刘伟军, 田志强, 徐效文, 李世磊, 索英祁. 面向多品种小批量制造过程的NAD-EWMA控制图多目标优化设计方法[J]. 机械工程学报, 2023, 59(3): 232-248.
[12]	喻天翔, 赵庆岩, 尚柏林, 宋笔锋. 考虑间隙不确定性的花键概率疲劳寿命预测方法[J]. 机械工程学报, 2022, 58(16): 391-402.
[13]	李博文, 贾祥, 赵骞, 郭波. 面向产品可靠性评估的退化和寿命数据分步融合方法[J]. 机械工程学报, 2022, 58(16): 430-440.
[14]	白光晗, 张驰, 兑红炎, 张云安, 陶俊勇. 无人机集群任务可靠性建模及重要度分析[J]. 机械工程学报, 2022, 58(10): 361-373.
[15]	张文鑫, 吕震宙. 一种新的自适应Kriging法停止准则及其在涡轮盘疲劳寿命可靠性中的应用[J]. 机械工程学报, 2022, 58(6): 263-273.