基于障碍网络颗粒阻尼器的悬臂梁减振特性研究

doi:10.3901/JME.2024.17.208

机械工程学报 ›› 2024, Vol. 60 ›› Issue (17): 208-222.doi: 10.3901/JME.2024.17.208

扫码分享

基于障碍网络颗粒阻尼器的悬臂梁减振特性研究

蒋捷¹, 杨元龙², 强陈¹, 闫超群³, 陈永辉³, 夏兆旺¹, 昝浩¹

1. 江苏科技大学能源与动力学院镇江 212003;
2. 中国船舶集团有限公司第七〇一研究所武汉 430064;
3. 中国船舶集团有限公司第七一一研究所上海 201108

收稿日期:2023-09-09 修回日期:2023-12-07 出版日期:2024-09-05 发布日期:2024-10-21
作者简介:蒋捷，男，1999年出生。主要研究方向为振动与噪声控制。E-mail:jiang13819555503@163.com
昝浩(通信作者)，男，1987年出生，博士，讲师，硕士研究生导师。主要研究方向为低频线谱减振技术及机械动力学、航空高精度燃油测量技术等。E-mail:zanhao870127@163.com
基金资助:
中国科学院热能动力技术重点实验室开放基金资助项目(TPL2020003)。

Study on Vibration Reduction Characteristics of Cantilever Beam Based on Particle Damper of Obstacle Network

JIANG Jie¹, YANG Yuanlong², QIANG Chen¹, YAN Chaoqun³, CHEN Yonghui³, XIA Zhaowang¹, ZAN Hao¹

1. School of Energy and Power Engineering, Jiangsu University of Science and Technology, Zhenjiang 212003;
2. The 701 Research Institute, China State Shipbuilding Corporation Limited, Wuhan 430064;
3. The 711 Research Institute, China State Shipbuilding Corporation Limited, Shanghai 201108

Received:2023-09-09 Revised:2023-12-07 Online:2024-09-05 Published:2024-10-21

摘要/Abstract

摘要： 障碍网络颗粒阻尼器是一种在颗粒阻尼器中内置三维网络的减振装置，通过增加颗粒与网络的碰撞与摩擦改变颗粒阻尼器的耗能特性。为研究障碍网络颗粒阻尼器附着在结构上的中低频减振特性，首先在填充比90%及颗粒粒径为2 mm 条件下，试验研究了附加障碍网络颗粒阻尼器后的悬臂梁结构在20～800 Hz频段的振动特性。其次，测量了特定频带(20～800 Hz)和激励范围(1～10g)下颗粒阻尼器与障碍网络颗粒阻尼器的损耗因子。最后通过离散元仿真探明了三维网络对附加在悬臂梁上颗粒阻尼器的能量损耗和颗粒运动的影响。研究结果表明，三维网络对于不同振动情况下有不同的影响，就悬臂梁而言，在一阶共振峰处(20 Hz)的减振效果较差，而在二阶(185 Hz)及三阶(520 Hz)共振峰处减振效果明显优于颗粒阻尼器。其原因在于在低频段颗粒运动幅值较大，网络会阻碍的颗粒的运动导致耗能降低；而在中频段网络打破颗粒的团聚效应，使更多的颗粒参与到耗能过程中，有效提升了颗粒阻尼器的阻尼性能。

关键词: 颗粒阻尼, 障碍网络, 悬臂梁, 损耗因子, 能量耗散

Abstract: The particle damper of obstacle network is a vibration damping device with a three-dimensional network built into the particle damper. The energy dissipation characteristics of the particle damper can be changed by increasing the collision and friction between the particle and the network. In order to study the vibration attenuation characteristics of the cantilever beam with the particle damper of obstacle network, the vibration characteristics of the cantilever beam with the particle damper of obstacle network attached at the frequency range of 20-800 Hz were experimentally studied under the condition of 90% filling ratio with 2 mm particle size. Secondly, the loss factors of particle dampers and particle dampers of obstacle network in specific frequency band (20～800 Hz) and specific vibration acceleration band (1-10g) are measured. Finally, the influence of the three-dimensional network on the energy loss and particle motion of the particle damper attached to the cantilever beam was investigated by discrete element simulation. The results show that the three-dimensional network has different effects on different vibration conditions. For the cantilever beam, the damping effect at the first order formant (20 Hz) is poor, but the damping effect at the second order formant (185 Hz) and the third order formant (520 Hz) is obviously better than the particle damper. The reason is that the motion amplitude of particles is large in the low frequency band, and the obstacle network will hinder the movement of particles, leading to the reduction of energy dissipation. However, the agglomeration effect of particles broken by the obstacle network in the middle frequency band enables more particles to participate in the energy dissipation process, which effectively improves the damping performance of the particle damper.

Key words: particle damper, obstacle network, cantilever beam, loss factor, energy dissipation

中图分类号:

TB535

蒋捷, 杨元龙, 强陈, 闫超群, 陈永辉, 夏兆旺, 昝浩. 基于障碍网络颗粒阻尼器的悬臂梁减振特性研究[J]. 机械工程学报, 2024, 60(17): 208-222.

JIANG Jie, YANG Yuanlong, QIANG Chen, YAN Chaoqun, CHEN Yonghui, XIA Zhaowang, ZAN Hao. Study on Vibration Reduction Characteristics of Cantilever Beam Based on Particle Damper of Obstacle Network[J]. Journal of Mechanical Engineering, 2024, 60(17): 208-222.

参考文献

[1] VEERAMUTHUVEL P, SHANKAR K, SAIRAJAN K K. Application of particle damper on electronic packages for spacecraft[J]. Acta Astronautica, 2016, 127:260-270.
[2] 叶林昌, 肖望强, 沈建平, 等. 基于粒子阻尼的动力装置基座减振优化设计研究[J]. 振动与冲击, 2021, 40(3):40-47. YE Linchang, XIAO Wangqiang, SHEN Jianping, et al. Optimization design of vibration reduction for power plant base based on particle damping[J]. Journal of Vibration and Shock, 2021, 40(3):40-47
[3] XIAO Wangqiang, XU Zhanhao, BIAN Hechuan, et al. Lightweight heavy-duty CNC horizontal lathe based on particle damping materials[J]. Mechanical Systems and Signal Processing, 2021, 147:107-127.
[4] LU Zheng, LIAO Yuan, HUANG Zhikuang. Stochastic response control of particle dampers under random seismic excitation[J]. Journal of Sound and Vibration, 2020, 481:115439.
[5] DUVIGNEAU F, KOCH S, WOSCHKE E, et al. An effective vibration reduction concept for automotive applications based on granular-filled cavities[J]. Journal of Vibration and Control, 2018, 24(1):73-82.
[6] 肖望强, 陈辉, 许展豪, 等. 基于颗粒阻尼的内燃动车组动力包构架多工况减振研究[J]. 机械工程学报, 2022, 58(4):250-257. XIAO Wangqiang, CHEN Hui, XU Zhanhao, et al. Study on the vibration reduction of internal combustion EMU powerpack frame under multiple loading conditions based on particle damping[J]. Journal of Mechanical Engineering, 2022, 58(4):250-257.
[7] GAGNON L, MORANDINI M, GHIRINGHELLI G L. A review of particle damping modeling and testing[J]. Journal of Sound and Vibration, 2019, 459:114865.
[8] MAO Kuanmin, WANG Yu, XU Zhiwei, et al. Simulation and characterization of particle damping in transient vibrations[J]. Journal of Vibration and Acoustics, 2004, 126(2):202-211.
[9] MAO Kuanmin, WANG Yu, XU Zhiwei, et al. DEM simulation of particle damping[J]. Powder Technology, 2004, 142(2-3):154-165.
[10] WONG C, DANIEL M C, RONGONG J A. Energy dissipation prediction of particle dampers[J]. Journal of Sound and Vibration, 2009, 319(1-2):91-118.
[11] BIONDANI F, MORANDINI M, GHIRINGHELLI G L, et al. Efficient discrete element modeling of particle dampers[J]. Processes, 2022, 10(7):12-47.
[12] 胡溧, 黄其柏, 柳占新, 等. 颗粒阻尼的动态特性研究[J]. 振动与冲击, 2009, 28(1):134-137+201. HU Li, HUANG Qibo, LIU Zhanxin, et al. Study on dynamic characteristics of particle damping[J]. Journal of Vibration and Shock, 2009, 28(1):134-137+201.
[13] 杨智春, 李泽江. 颗粒碰撞阻尼动力吸振器的设计及试验研究[J]. 振动与冲击, 2010, 29(6):69-71+143+236. YANG Zhichun, LI Zejiang. Design and experimental study of dynamic vibration absorber with particle impact damping[J]. Journal of Vibration and Shock, 2010, 29(6):69-71+143+236.
[14] XIA Zhaowang, MAO Kaijie, WEI Shoubei, et al. Application of genetic algorithm-support vector regression model to predict damping of cantilever beam with particle damper[J]. Journal of Low Frequency Noise, Vibration and Active Control, 2017, 36(2):138-147.
[15] YE Xin, NI Yiqing, SAJJADI M, et al. Physics-guided, data-refined modeling of granular material-filled particle dampers by deep transfer learning[J]. Mechanical Systems and Signal Processing, 2022, 180:109437.
[16] 陈武龙. 悬臂梁颗粒阻尼系统减振特性的试验研究[D]. 沈阳:东北大学, 2014. CHEN Wulong. Experimental study on vibration reduction characteristics of particle damping system of cantilever beam[D]. Shenyang:Northeastern University, 2014.
[17] ZHANG Kai, CHEN Tianning, WANG Xiaopeng, et al. Rheology behavior and optimal damping effect of granular particles in a non-obstructive particle damper[J]. Journal of Sound and Vibration, 2016, 364:30-43.
[18] YIN Zhongjun, SU Fan, ZHANG Huang. Investigation of the energy dissipation of different rheology behaviors in a non-obstructive particle damper[J]. Powder Technology, 2017, 321:270-275.
[19] MEYER N, SEIFRIED R. Energy dissipation in horizontally driven particle dampers of low acceleration intensities[J]. Nonlinear Dynamics, 2022:1-16.
[20] MEYER N, SEIFRIED R. Numerical and experimental investigations in the damping behavior of particle dampers attached to a vibrating structure[J]. Computers & Structures, 2020, 238:106281.
[21] MEYER N, SEIFRIED R. Toward a design methodology for particle dampers by analyzing their energy dissipation[J]. Computational Particle Mechanics, 2021, 8(4):681-699.
[22] MEYER N, SCHWARTZ C, MORLOCK M, et al. Systematic design of particle dampers for horizontal vibrations with application to a lightweight manipulator[J]. Journal of Sound and Vibration, 2021, 510:116319.
[23] JADHAV T A, AWASARE P J. Enhancement of particle damping effectiveness using multiple cell enclosure[J]. Journal of Vibration and Control, 2016, 22(6):1516-1525.
[24] 肖望强, 黄玉祥, 李威, 等. 颗粒阻尼器配置对齿轮传动系统动特性影响[J]. 机械工程学报, 2017, 53(7):1-12. XIAO Wangqiang, HUANG Yuxiang, LI Wei, et al. Influence of particle damper configurations on the dynamic characteristic for gear transmission system[J]. Journal of Mechanical Engineering, 2017, 53(7):1-12.
[25] LIU Wei, TOMLINSON G R, RONGONG J A. The dynamic characterization of disk geometry particle dampers[J]. Journal of Sound and Vibration, 2005, 280(3-5):849-861.
[26] FERREYRA M V, GÓMEZ-PACCAPELO J M, SUAREZ R, et al. Avoiding chaos in granular dampers[C]//EPJ Web of Conferences. EDP Sciences, 2021, 249:15003.
[27] YAO Bing, CHEN Qian. Investigation on zero-gravity behavior of particle dampers[J]. Journal of Vibration and Control, 2015, 21(1):124-133.
[28] GNANASAMBANDHAM C, FLEISSNER F, EBERHARD P. Enhancing the dissipative properties of particle dampers using rigid obstacle-grids[J]. Journal of Sound and Vibration, 2020, 484:115522.
[29] XUE Cheng, XU Xiangxi, SU Zhanfa, et al. Based on steady flow method to identify the semi-active particle damping loss factor experiment[J]. Journal of Aerospace Power, 2020, 35(1):60-65.
[30] HU Li, TANG Zhe, XU Xian, et al. Particle damper loss factor external characteristic study[J]. China Mechanical Engineering, 2015, 26(15):2005-2009.
[31] ROMDHANE M B, BOUHADDI, TRIGUI M, et al. The loss factor experimental characterization of the non- obstructive particles damping approach[J]. Mechanical Systems and Signal Processing, 2013, 38(2):585-600.
[32] KENNETH L J. Contact mechanics[M]. Cambridge:Cambridge University Press, 1987.
[33] MINDLIN R D. Elastic spheres in contact under varying oblique forces[J]. Journal of Applied Mechanics, 1949, 16(7):327-330.
[34] 刘艳, 梁要, 陈亚楠, 等. 颗粒阻尼减振特性研究[J]. 噪声与振动控制, 2021, 41(4):13-18. LIU Yan, LIANG Yao, CHEN Yanan, et al. Study on vibration reduction characteristics of particle damping[J]. Noise and Vibration Control, 2021, 41(4):13-18.
[35] 肖望强, 卢大军, 宋黎明, 等. 基于颗粒阻尼的矿用自卸车振动舒适性[J]. 交通运输工程学报, 2019, 19(6):111-124. XIAO Wangqiang, LU Dajun, SONG Liming, et al. Vibration comfort of mining dump truck based on particle damping[J]. Journal of Traffic and Transportation Engineering, 2019, 19(6):111-124

基于障碍网络颗粒阻尼器的悬臂梁减振特性研究

Study on Vibration Reduction Characteristics of Cantilever Beam Based on Particle Damper of Obstacle Network

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈磊, 刘阳钦, 唐川, 蒋翼隆, 石鹏飞, 钱林茂. 面向超精密加工的微观材料去除机理研究进展[J]. 机械工程学报, 2023, 59(23): 229-264.
[2]	赵文滔, 杨颜志, 王长焕, 鞠雪梅, 严刚. 基于贝叶斯推断的复合材料层间内聚力模型参数反演[J]. 机械工程学报, 2022, 58(6): 110-118.
[3]	肖望强, 陈辉, 许展豪, 王兴民, 贾尚帅, 潘德阔. 基于颗粒阻尼的内燃动车组动力包构架多工况减振研究[J]. 机械工程学报, 2022, 58(4): 250-257.
[4]	杨文平, 郭杏林, 赵延广. 对流和辐射换热对金属高周疲劳能量耗散估计的影响[J]. 机械工程学报, 2021, 57(10): 187-195.
[5]	何威, 魏彦京. 集中荷载作用下双层弹性悬臂梁动力学分析[J]. 机械工程学报, 2021, 57(1): 128-137.
[6]	戴荣, 于海涛, 王权. 基于Duffing系统的谐振式微悬臂梁传感器微弱谐振信号检测[J]. 机械工程学报, 2020, 56(13): 50-59.
[7]	李瑞君, 常振鑫, 雷英俊, 胡鹏浩, 范光照. 基于DVD光学读取头的悬臂式低频加速度计[J]. 机械工程学报, 2019, 55(2): 10-17.
[8]	陈永会, 张学良, 温淑花, 兰国生. 考虑弹塑性阶段的结合面法向接触阻尼分形模型[J]. 机械工程学报, 2019, 55(16): 58-68.
[9]	朱军华, 苏伟, 刘人怀, 宋芳芳, 黄钦文. 静电驱动阶梯型微悬臂梁吸合电压分析[J]. 机械工程学报, 2018, 54(8): 217-222.
[10]	李炜, 鲍雄, 周仲荣. 微创手术缝合针刺破组织过程中能量耗散研究[J]. 机械工程学报, 2018, 54(7): 107-113.
[11]	樊俊铃. 基于能量耗散的Q235钢高周疲劳性能评估[J]. 机械工程学报, 2018, 54(6): 1-9.
[12]	罗忠, 刘昊鹏, 朱云鹏, 王菲, 韩清凯. 基于REFOR算法的多输出非线性系统动态参数化建模方法研究[J]. 机械工程学报, 2018, 54(23): 73-81.
[13]	李一堃, 郝志明. 连接结构宏观滑移能量耗散特性研究[J]. 机械工程学报, 2018, 54(15): 125-131.
[14]	肖望强, 黄玉祥, 李威, 林宏, 陈智伟. 颗粒阻尼器配置对齿轮传动系统动特性影响^*[J]. 机械工程学报, 2017, 53(7): 1-12.
[15]	王根, 林建平, 孙鑫, 金晶. 基于最大正应力的自升式平台悬臂梁框架轻量化优化设计[J]. 机械工程学报, 2017, 53(7): 173-179.