利用中低频振动改善熔丝制造产品表面加工质量研究

doi:10.3901/JME.2021.21.119

机械工程学报 ›› 2021, Vol. 57 ›› Issue (21): 119-125.doi: 10.3901/JME.2021.21.119

扫码分享

利用中低频振动改善熔丝制造产品表面加工质量研究

姜世杰¹, 胡科¹, 董天阔¹, 战明², 戴卫兵¹

1. 东北大学机械工程与自动化学院沈阳 110819;
2. 东北大学信息科学与工程学院沈阳 110819

收稿日期:2020-10-30 修回日期:2021-04-01 出版日期:2021-11-05 发布日期:2021-12-28
通讯作者: 姜世杰(通信作者),男,1985年出生,博士,副教授,硕士研究生导师。主要研究方向为振动利用工程。E-mail:jiangsj@me.neu.edu.cn
基金资助:
国家自然科学基金（51705068）和中央高校基本科研业务费专项资金（N180703009，N170302001）资助项目。

Investigation on Improving the Surface Quality of Fused Filament Fabrication Products by Low and Medium Frequency Vibration

JIANG Shijie¹, HU Ke¹, DONG Tiankuo¹, ZHAN Ming², DAI Weibing¹

1. School of Mechanical Engineering & Automation, Northeastern University, Shenyang 110819;
2. College of Information Science & Engineering, Northeastern University, Shenyang 110819

Received:2020-10-30 Revised:2021-04-01 Online:2021-11-05 Published:2021-12-28

摘要/Abstract

摘要： 熔丝制造技术（Fused filament fabrication，FFF）因其操作简单、适用性强和成本低廉等特点，已经成为当今使用最为广泛的增材制造技术之一。然而，由于逐层累加的工艺特点，与传统加工方式相比FFF产品的表面质量存在着明显的缺陷。利用中低频振动在改善FFF产品表面质量方面有着很大的潜力，为此，将压电陶瓷与增材制造设备相结合，首先将普通FFF设备改装成振动式FFF设备；然后通过控制输入信号和电压，以控制压电陶瓷的输出振动参数，从而利用施加振动前和不同形式振动后的试验样件，并完成表面粗糙度测试；通过对比分析不同样件的试验结果，阐明利用振动对FFF产品表面质量的影响规律。结果表明，利用中低频振动能够有效改善FFF产品的表面质量，且随着振动频率或幅值的增大，表面质量将进一步提高。

关键词: 熔丝制造, 利用振动, 压电陶瓷, 试验样件, 表面质量

Abstract: Fused filament fabrication (FFF) has become one of the most widely used additive manufacturing technologies due to its simple operation, strong applicability, low manufacturing costs, etc. However, due to the layer-by-layer manufacturing characteristics, FFF products have obvious defects in surface quality compared with those fabricated by traditional methods. Since using vibration of low and medium frequency has great potential in improving the surface quality of FFF products, the piezoelectric ceramics are combined with the additive manufacturing equipment. An ordinary FFF equipment is firstly converted into a vibrating one; The output vibration of the piezoelectric ceramic can be controlled by controlling the input signal and voltage. Relevant testing samples are then prepared without and with different types of vibration vtilized, and the corresponding surface roughness measurements are carried out; Through the comparison between different samples' testing results, the influencing rule of the vtilized vibration is clarified. The results show that introducing vibration of low and medium frequency into FFF process can significantly improve the surface quality of FFF products, and it will be further improved with the increase of frequency or amplitude of the vtilized vibration.

Key words: fused filament fabrication, using vibration, piezoelectric ceramics, testing sample, surface quality

中图分类号:

TG156

姜世杰, 胡科, 董天阔, 战明, 戴卫兵. 利用中低频振动改善熔丝制造产品表面加工质量研究[J]. 机械工程学报, 2021, 57(21): 119-125.

JIANG Shijie, HU Ke, DONG Tiankuo, ZHAN Ming, DAI Weibing. Investigation on Improving the Surface Quality of Fused Filament Fabrication Products by Low and Medium Frequency Vibration[J]. Journal of Mechanical Engineering, 2021, 57(21): 119-125.

参考文献

[1] SIMON F, MĚLANIE D. Additive manufacturing and sustainability:An exploratory study of the advantages and challenges[J]. Journal of Cleaner Production, 2016, 137:1573-1587.
[2] CHEN Lian, HE Yong, YANG Yingxin, et al. The research status and development trend of additive manufacturing technology[J]. The International Journal of Advanced Manufacturing Technology, 2016, 89:3651-3660.
[3] OMAR A, SYED H, JAHAR L. Optimization of fused deposition modeling process parameters:A review of current research and future prospects[J]. Advances in Manufacturing, 2015, 3:42-53.
[4] 何新英, 陶明元, 叶春生. FDM工艺成形过程中影响成形精度的因素分析[J]. 机械电子, 2004(9):77-78. HE Xinying, TAO Mingyuan, YE Chunsheng, Analysis for factors that affect the precision of the shaped pieces on fused deposition modeling process[J]. Mechanics and Electronics, 2004(9):77-78.
[5] LI Zhixiong, ZHANG Ziyang, SHI Junchuan, et al. Prediction of surface roughness in extrusion-based additive manufacturing with machine learning[J]. Robotics and Computer-Integrated Manufacturing, 2019, 57:488-495.
[6] KIM M K, LEE H I, KIM H C. Effect of fabrication parameters on surface roughness of FDM parts[J]. International Journal of Precision Engineering and Manufacturing, 2018, 1(19):137-142.
[7] YANG Leipeng, LI Shujun, LI Yan, et al. Experimental investigations for optimizing the extrusion parameters on FDM PLA printed parts[J]. Journal of Materials Engineering and Performance, 2018, 28(1):169-182.
[8] CHEN Lan, ZHANG Xinzhou. Modification the surface quality and mechanical properties by laser polishing of Al/PLA part manufactured by fused deposition modeling[J]. Applied Surface Science, 2019, 429:765-775.
[9] JAYANTH N, SENTHIL P, PRAKASH C, Effect of chemical treatment on tensile strength and surface roughness of 3D-printed ABS using the FDM process[J]. Virtual and Physical Prototyping, 2018, 13(3):155-163.
[10] BENIAK J, KRIŽAN P, ĹUBOMĺR Š, et al. Roughness and compressive strength of FDM 3D printed specimens affected by acetone vapour treatment[J]. IOP Conference Series:Materials Science and Engineering, 2018, 297:1-8.
[11] SUNPREET S, MANJEET S, CHANDER P, et al. Optimization and reliability analysis to improve surface quality and mechanical characteristics of heat-treated fused filament fabricated parts[J]. The International Journal of Advanced Manufacturing Technology, 2019, 102:1521-1536.
[12] LI Guiwei, ZHAO Ji, JIANG Jili, et al. Ultrasonic strengthening improves tensile mechanical performance of fused deposition modeling 3D printing[J]. The International Journal of Advanced Manufacturing Technology, 2018, 96:2747-2755.
[13] 盛敏刚, 严永新, 张金花, 等. 环境友好型生物降解材料聚乳酸的性能研究[J]. 中国农学通报, 2007, 23(9):499-503. SHENG Mingang, YAN Yongxin, ZHANG Jinhua, et al. Study on properties of environment-friendly biodegradable material polyactic acid[J]. Chinese Agricultural Science Bulletin, 2007, 23(9):499-503.

[1]	殷振, 张坤, 戴晨伟, 程敬彩, 徐海龙, 李华. 超声椭圆振动磨削SiC陶瓷的砂轮磨损与磨削性能研究[J]. 机械工程学报, 2024, 60(9): 57-74.
[2]	陈守峰, 王成勇, 李伟秋, 丁峰, 卢耀安, 周玉海. 超声振动铣削加工石墨材料去除机理与加工表面质量评价[J]. 机械工程学报, 2024, 60(9): 86-96.
[3]	郑开魁, 赵信哲, 牟刚, 任志英. 超声波滚压强化TC11钛合金的表面质量与摩擦磨损性能[J]. 机械工程学报, 2024, 60(9): 137-151.
[4]	李继成, 陈广俊, 许金凯, 于化东. C/SiC复合材料激光超声复合微切削材料损伤机理与表面质量研究[J]. 机械工程学报, 2024, 60(9): 189-205.
[5]	岳晓明, 臧烁, 赵永华, 刘为东, 尹瀛月, 张勤河. 高品质超大深径比小孔电火花电解复合加工实验研究[J]. 机械工程学报, 2024, 60(9): 374-382.
[6]	宋阳, 曹华军, 张金, 刘磊, 张琼之. 纤维随机分布CFRP高速铣削比能模型与表面质量优化[J]. 机械工程学报, 2024, 60(1): 65-74.
[7]	李明星, 岳彩旭, 刘献礼, 陈志涛, 姜志鹏, 岳大荀, STEVEN Y L. 钛合金框架类零件铣削用立铣刀设计与应用研究进展[J]. 机械工程学报, 2023, 59(23): 283-309.
[8]	彭小强, 李煌, 王跃明, 关朝亮, 胡皓, 赖涛, 徐超. 化学镀NiP的凸面闪耀光栅超精密切削特性研究[J]. 机械工程学报, 2023, 59(21): 121-130.
[9]	王可, 周平, 闫英, 张超, 郭东明. 铜表面脉冲电化学射流加工的定域性和粗糙度分析[J]. 机械工程学报, 2022, 58(7): 258-266.
[10]	王敏杰, 王阳, 魏兆成, 段春争. 切削过程绝热剪切带的滑移线场研究[J]. 机械工程学报, 2022, 58(7): 284-294.
[11]	张振宇, 吴俊, 宋克峰, 郭昭志, 程军. 钛合金超微细磨削中磨削力和加工表面质量的研究[J]. 机械工程学报, 2022, 58(15): 75-91.
[12]	何雨镐, 谢福贵, 刘辛军, 张旭. 大型构件机器人原位加工中的测量方案概述[J]. 机械工程学报, 2022, 58(14): 1-14.
[13]	郑开魁, 林有希, 蔡建国, 雷成迁. 超声滚压工艺对模具钢激光熔覆层表面质量的影响[J]. 机械工程学报, 2022, 58(12): 111-120.
[14]	张翔宇, 路正惠, 彭振龙, 张德远. 钛合金的高质高效超声振动切削加工[J]. 机械工程学报, 2021, 57(5): 133-147.
[15]	郭江, 王兴宇, 赵勇, 许永波, 崔海龙, 魏兆成, 金洙吉, 康仁科. 微织构刀具制备技术及加工性能研究新进展[J]. 机械工程学报, 2021, 57(13): 172-200.

利用中低频振动改善熔丝制造产品表面加工质量研究

Investigation on Improving the Surface Quality of Fused Filament Fabrication Products by Low and Medium Frequency Vibration

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价