电涡流传感器线圈阻抗计算方法

›› 2007, Vol. 43 ›› Issue (2): 210-214.

电涡流传感器线圈阻抗计算方法

于亚婷;杜平安;李代生

电子科技大学机械电子工程学院;重庆大学机械传动国家重点实验室;中国工程物理研究院总体工程研究所

发布日期:2007-02-15

COMPUTATIONAL METHODS OF COIL IMPEDANCE OF EDDY CURRENT SENSOR

YU Yating;DU Ping’an;LI Daisheng

School of Mechatronics Electronics Engineering, University of Electronic Science and Technology of China State Key Laboratory of Mechanical Transmissions, Chongqing University Institute of Southwest Structure Engineering,Chinese Academy of Engineering Physics

Published:2007-02-15

摘要/Abstract

摘要： 针对电涡流传感器的线圈阻抗值计算问题，提出理论计算法和有限元法两种方法。以厚度为δ的被测体(含磁性和非磁性导体)上方正对一圆柱型线圈为求解模型，根据传感器工作原理和电磁场理论导出线圈阻抗积分表达式，并将其转化为更易求解的级数表达形式，由MathematicTM计算线圈阻抗值。然后根据有限元建模理论建立传感器的有限元模型，通过仿真得到传感器磁力线分布和线圈阻抗值。最后比较两种方法得到的阻抗值，结果表明两种方法计算结果相符，其有效性和正确性得到相互验证。

关键词: 电涡流传感器, 级数表达形式, 线圈, 有限元法, 阻抗计算

Abstract: To research the computational methods about the transducer coil impedance with the magnetic and non-magnetic measured target, two computational methods, theoretic method and finite element method, are proposed. The computational model of the coil impedance is simplified as a cylindrical coil over a cylindrical measured target with the thickness δ. According to the sensor measurement principal and the electromagnetic theory, the integral expression of the coil impedance is derived, which is expanded by series in polar coordinate system in order to compute easily and feasibly. And the coil impedance value is computed by MathematicTM. Then, based on the modeling theory of finite element method, the finite element model is built. The coil impedance value and the magnetic distribution figures are obtained by finite element analysis, respectively. Finally, the results from the derivation and finite element analysis are in agreement very well by comparison, and they are given to validate the accuracy and feasibility of the derivation method with finite element method.

Key words: Eddy current sensor, Finite element method, Impedance computation, Series expansions, Transducer coil

中图分类号:

TM154.1 TP391.7

于亚婷;杜平安;李代生. 电涡流传感器线圈阻抗计算方法[J]. , 2007, 43(2): 210-214.

YU Yating;DU Ping’an;LI Daisheng. COMPUTATIONAL METHODS OF COIL IMPEDANCE OF EDDY CURRENT SENSOR[J]. , 2007, 43(2): 210-214.

[1]	胡波,黄绍波,周进,张跃,谢志辉,杨帅,黄泽. 发电机定子线圈介质损耗分段式伪三电极测试方法研究[J]. 电气工程学报, 2019, 14(2): 103-107.
[2]	张军, 刘佳欢, 王雪萍, 马贺. 基于有限元摩擦功计算的钢轨磨耗预测方法[J]. 机械工程学报, 2019, 55(14): 104-111.
[3]	张满,冉军德,田芝华,费夕刚,邹灿,胡飞. 带电雾凇覆冰后分裂导线电场分布模型分析[J]. 电气工程学报, 2018, 13(8): 43-48.
[4]	谭援强, 蒋理宽, 姜胜强, 杨世平, 刘思思, 胡检发. 渐开线花键副微动摩擦接触分析[J]. 机械工程学报, 2018, 54(7): 123-130.
[5]	路倩云,王文清,翟志颖,田子建. 三线圈无线输电系统的频率分裂特性和抑制方法[J]. 电气工程学报, 2018, 13(5): 27-32.
[6]	张合吉, 何泽寒, 刘建桥, 吴磊, 王衡禹, 温泽峰. 地铁异常磨耗车轮与辙叉接触分析[J]. 机械工程学报, 2018, 54(4): 117-123.
[7]	寇峻瑜, 王衡禹, 赵鑫, 赵国堂, 金学松. 钢轨脱碳层对轮轨瞬态滚动接触行为的影响分析[J]. 机械工程学报, 2018, 54(4): 101-108.
[8]	吴家腾, 杨宇, 程军圣. 基于解析有限元的齿根裂纹时变啮合刚度计算方法[J]. 机械工程学报, 2018, 54(23): 56-62.
[9]	贵新成, 李立顺, 李红勋, 詹隽青, 薛兴东. 高重合度摆线内齿轮副时变啮合刚度计算与齿间载荷分配研究[J]. 机械工程学报, 2018, 54(21): 101-112.
[10]	葛月, 牛军川, 刘知辉. 多种激励形式下任意角度耦合板振动传递特性研究^*[J]. 机械工程学报, 2017, 53(7): 94-103.
[11]	冯海全, 仇洪然, 刘佳, 王永刚. 永久性腔静脉滤器的生物力学和血流动力学性能分析^*[J]. 机械工程学报, 2017, 53(6): 187-194.
[12]	刘超, 赵鑫, 赵小罡, 寇峻瑜, 温泽峰. 单侧钢轨波磨对两侧轮轨瞬态响应的影响分析[J]. 机械工程学报, 2017, 53(22): 117-124.
[13]	梁娜,鲍晓华. 转子槽形对笼型电机附加损耗的影响[J]. 电气工程学报, 2017, 12(11): 7-11.
[14]	郑建芬,王春芳,王放,夏东伟. 非晶和硅钢混合铁心风电电抗器的电磁热场模拟[J]. 电气工程学报, 2017, 12(10): 19-24.
[15]	孙建亮, 邱丑武, 毕雪峰, 王实. 感应加热与传统加热模式大型筒节加热效果研究[J]. 机械工程学报, 2017, 53(10): 25-33.