• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (17): 309-321.doi: 10.3901/JME.260916

• 机器人及机构学 • 上一篇    

扫码分享

内啮合强力珩齿机几何误差建模与迭代补偿方法

张友, 李聪波, 曹华军, 陶桂宝   

  1. 重庆大学高端装备机械传动全国重点实验室 重庆 400044
  • 收稿日期:2024-11-25 修回日期:2025-02-26 发布日期:2026-11-20
  • 作者简介:张友,男,1996年出生,博士研究生。主要研究方向为齿轮绿色与精密制造。E-mail:zhangyou96@163.com;李聪波(通信作者),男,1981年出生,博士,教授,博士研究生导师。主要研究方向为绿色制造装备与系统。E-mail:congboli@cqu.edu.cn
  • 基金资助:
    国家重点研发计划(2023YFB3406500)、中央高校基本科研业务费资助项目(2023CDJYXTD-003)和高端装备机械传动全国重点实验室自主研究课题(SKLMT-ZZKT-2024Z06)资助项目。

Geometric Error Modeling and Iterative Compensation Method of Internal Gear Power Honing Machine

ZHANG You, LI Congbo, CAO Huajun, TAO Guibao   

  1. State Key Laboratory of Mechanical Transmission for Advanced Equipment, Chongqing University, Chongqing 400044
  • Received:2024-11-25 Revised:2025-02-26 Published:2026-11-20

摘要: 内啮合强力珩齿工艺产生的特殊齿面纹理可有效降低啮合噪声,被广泛应用于新能源汽车电驱传动系统的齿轮加工中。内啮合强力珩齿工艺涉及多轴联动和复杂的刀具运动轨迹,几何误差数量众多、耦合机理复杂,对加工精度影响更为显著。为提高珩齿加工精度,提出一种内啮合强力珩齿机几何误差建模与迭代补偿方法。首先系统分析多轴耦合下内啮合强力珩齿机几何误差的传递机理,建立内啮合强力珩齿机的几何误差模型,然后构建几何误差与工件齿面偏差的映射模型,通过敏感性分析识别出影响工件齿面偏差的关键几何误差,提出面向关键几何误差的迭代补偿策略,最后通过案例分析和补偿方法对比,验证所提方法的有效性和实用性。

关键词: 几何误差建模, 迭代补偿, 内啮合强力珩齿, 敏感性分析

Abstract: The internal gear power honing process produces a special tooth surface texture that effectively reduces mesh noise, and is widely used in the gear machining of electric drive transmission systems for electric vehicles. The internal gear power honing process involves multi-axis linkage and complex tool trajectory. There are a large number of geometric errors and complex coupling mechanism, which has a significant impact on machining accuracy. To improve the machining accuracy of gear honing, a geometric error modeling and iterative compensation method for internal gear power honing machine is proposed. Firstly, the transmission mechanism of geometric errors of internal gear power honing machine under multi-axis coupling is systematically analyzed, and the geometric error model is established. Then, the mapping model of geometric error and workpiece tooth surface deviation is constructed. The crucial geometric errors affecting tooth surface deviation are identified by sensitivity analysis, and an iterative compensation strategy for crucial geometric errors is proposed. Finally, the effectiveness and practicability of the proposed method are verified by case analysis and compensation method comparison.

Key words: geometric error modeling, iterative compensation, internal gear power honing, sensitivity analysis

中图分类号: