热轧工作辊服役状态在线监测与主动再制造时机在线决策方法研究

doi:10.3901/JME.2024.24.056

机械工程学报 ›› 2024, Vol. 60 ›› Issue (24): 56-65.doi: 10.3901/JME.2024.24.056

扫码分享

热轧工作辊服役状态在线监测与主动再制造时机在线决策方法研究

宋守许^1,2, 张宇浩^1,2, 蔚辰^1,2, 李想^1,2, 徐瑞^1,2

1. 合肥工业大学机械工程学院合肥 230009;
2. 合肥工业大学机械工业绿色设计与制造重点实验室合肥 230009

收稿日期:2024-03-05 修回日期:2024-08-09 出版日期:2024-12-20 发布日期:2025-02-01
作者简介:宋守许，男，1964年出生，博士，教授。主要研究方向为机电产品绿色设计与绿色制造、再制造理论与技术、产品再资源化技术与装备。E-mail：shouxus@163.com;张宇浩(通信作者)，男，1999年出生。主要研究方向为机电产品绿色设计与再制造，热轧在线监测技术。E-mail：zhang_yhao@163.com
基金资助:
国家自然科学基金(52205100, 52275111, 52205101, U23A20620)、广东省基础与应用基础研究基金(2023A1515012856, 2023A1515240021, 2021A1515110708)资助项目。

Research on On-line Monitoring of Service Status of Hot Rolled Work Rolls and On-line Decision-making Method for Active Remanufacturing

SONG Shouxu^1,2, ZHANG Yuhao^1,2, WEI Chen^1,2, LI Xiang^1,2, XU Rui^1,2

1. School of Mechanical Engineering, Hefei University of Technology, Hefei 230009;
2. Key Laboratory for Green Design and Manufacturing of Machinery Industry, Hefei University of Technology, Hefei 230009

Received:2024-03-05 Revised:2024-08-09 Online:2024-12-20 Published:2025-02-01

摘要/Abstract

摘要： 轧辊再制造工作具有良好的经济、环境和社会效益，但退役轧辊性能与退役时间不确定性问题影响着轧辊再制造工作的效率与成本。通过热轧制实验模拟实际工业轧制状况中高速钢工作辊性能指标退化，根据不同性能指标对轧辊以及轧制过程的危害程度，构建了包含硬度、磨损量、耐磨性、表面摩擦因数的轧辊状态评估指标集，并提出了贝塔分布-推土机距离方法用于融合轧辊状态评估指标集，构建出具有综合性的轧辊健康状态指标 (Healthy indicator, HI)。基于指标HI将轧辊退化过程划分为磨合、稳定退化和迅速劣化三个阶段，基于Ville拐点监测方法确定了热轧工作辊主动再制造时机点。最后，采集不同状态下轧辊表面的涡流信号，提取涡流信号希尔伯特谱的能量和为工作辊退化特征，通过构建退化特征与HI映射模型，实现了高速钢工作辊综合性能退化的在线监测与定量表征，以及主动再制造时机的在线抉择。

关键词: 工作辊, Beta-EMD方法, 健康指标, 在线监测, 再制造时机

Abstract: Performance and uncertain timeline to retirement affect efficiency and cost of work roll remanufacturing, which is beneficial for economy, environment and society. Investigates performance degradation of high-speed steel work rolls in the simulated rolling process. It presents an indicator set including hardness, wear amount, abrasion resistance, and surface roughness, illustrating harm to the work rolls and rolling. Based on the set and Beta-earth mover’s distance(Beta-EMD), it proposes a comprehensive health indicator(HI) of work roll, illustrating running-in, stable degradation and rapid deterioration. According to detection of Ville turning point, it becomes clear to remanufacture the hot work rolls. According to the Hilbert spectrum of the eddy current signals on the surface of the work rolls and the mapping models of degradation and HI, it is possible to conduct online monitoring of performance degradation of the high-speed steel work rolls, perform quantitative characterization and determine remanufacturing.

Key words: work roll pulsed, Beta-EMD method, healthy indicator, on-line monitoring, remanufacturing timing

中图分类号:

TG156

宋守许, 张宇浩, 蔚辰, 李想, 徐瑞. 热轧工作辊服役状态在线监测与主动再制造时机在线决策方法研究[J]. 机械工程学报, 2024, 60(24): 56-65.

SONG Shouxu, ZHANG Yuhao, WEI Chen, LI Xiang, XU Rui. Research on On-line Monitoring of Service Status of Hot Rolled Work Rolls and On-line Decision-making Method for Active Remanufacturing[J]. Journal of Mechanical Engineering, 2024, 60(24): 56-65.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2024.24.056

http://www.cjmenet.com.cn/CN/Y2024/V60/I24/56

参考文献

[1] SINGH G，SINGH P K. Effect of process parameters on roll separating force，driving torque and end crop length during grooved hot rolling of SAE 1020 steel[J]. Journal of Manufacturing Processes，2022，79：1003-1016.
[2] HU K J，XIA Y M，ZHU F X，et al. Evaluation of thermal breakage in bimetallic work roll considering heat treated residual stress combined with thermal stress during hot rolling[J]. Steel Research International，2018，89：1-8.
[3] DONG Q，WANG Z，HE Y，et al. The effect of shifting modes on work roll wear in strip steel hot rolling process[J]. Ironmaking & Steelmaking，2023，50(1)：67-74.
[4] WEIDLICH F，BRAGA A P V，LIMA L G D B，et al. The influence of rolling mill process parameters on roll thermal fatigue[J]. The International Journal of Advanced Manufacturing Technology，2019，102：2159-2171.
[5] WU S，XING W，LIU Y，et al. Research on dynamic characteristics and identification method of local defect on the roll surface[J]. Engineering Failure Analysis，2021，121：105063.
[6] LI G，LIU J，JIANG G，et al. Numerical simulation of temperature field and thermal stress field in the new type of ladle with the nanometer adiabatic material[J]. Advances in Mechanical Engineering，2015，7(4)：1-13.
[7] 范沁红，马立峰，赵镇波，等. 镁合金轧制热流体式控温轧辊温度变化规律研究[J]. 机械工程学报，2022，58(8)：143-152.FAN Qinhong，MA Lifeng，ZHAO Zhenbo，et al. Temperature variation of internal oil flowing temperature-control roller for Mg alloy rolling[J]. Journal of Mechanical Engineering，2022，58(8)：143-152.
[8] GARZA-MONTES-DE-OCA N F，COLÁS R，RAINFORTH W M. On the damage of a work roll grade high speed steel by thermal cycling[J]. Engineering Failure Analysis，2011，18(6)：1576-1583.
[9] XU L，SONG W，MA S，et al. Effect of slippage rate on frictional wear behaviors of high-speed steel with dual-scale tungsten carbides (M6C) under high-pressure sliding-rolling condition[J]. Tribology International，2021，154：106719.
[10] DENG G Y，ZHU H T，TIEU A K，et al. Theoretical and experimental investigation of thermal and oxidation behaviours of a high speed steel work roll during hot rolling[J]. International Journal of Mechanical Sciences，2017，131：811-826.
[11] DENG G Y，ZHU Q，TIEU K，et al. Evolution of microstructure，temperature and stress in a high speed steel work roll during hot rolling： Experiment and modelling[J]. Journal of Materials Processing Technology，2017，240：200-208.
[12] XU L，SONG W，MA S，et al. Effect of slippage rate on frictional wear behaviors of high-speed steel with dual-scale tungsten carbides (M6C) under high-pressure sliding-rolling condition[J]. Tribology International，2021，154：106719.
[13] SUN C G，HWANG S M，YUN C S，et al. Investigation of thermomechanical behavior of a work roll and of roll life in hot strip rolling[J]. Metallurgical and Materials Transactions A，1998，29：2407-2424.
[14] 宋守许，郁炯，蔚辰，等. 考虑多辊修磨关系的轧辊主动再制造设计方法[J]. 机械工程学报，2022，58(13)：203-212.SONG Shouxu，YU Jiong，WEI Chen，et al. Predecisional remanufacturing design method of rolls considering multi-roll repair and grinding relationship[J]. Journal of Mechanical Engineering，2022，58(13)：203-212.
[15] RYU K S，NAHM S H，KIM Y B，et al. Dependence of magnetic properties on isothermal heat treatment time for 1Cr–1Mo–0.25 V steel[J]. Journal of Magnetism and Magnetic Materials，2000，222(1-2)：128-132.
[16] LIM H B，YANG H I，KIM C W. Analysis of the roll hunting force due to hardness in a hot rolling process[J]. Journal of Mechanical Science & Technology，2019，33(8)：3783-3793.
[17] DELAUNOIS F，STANCIU V I，MEGRET A，et al. Oxidation and wear behavior of high-speed steel and semi-high-speed steel used in hot strip mill[J]. The International Journal of Advanced Manufacturing Technology，2022，119(1-2)：677-689.
[18] BATAILLE C，LUC E，BIGERRELLE M，et al. Rolls wear characterization in hot rolling process[J]. Tribology International，2016，100：328-337.
[19] RUBNER Y，TOMASI C，GUIBAS L J. The earth mover's distance as a metric for image retrieval[J]. International Journal of Computer Vision，2000，40(2)：99.
[20] 宋守许，汪志全，蔚辰. 基于在线监测的曲轴主动再制造时机识别[J]. 现代制造工程，2020，47(8)：7-12.SONG Shouxu，WANG Zhiquan，WEI Chen. Timing recognition of crankshaft predecisional remanufacturing based on online monitoring[J]. Modern Manufacturing Engineering，2020，47(8)：7-12.
[21] FERMIN-CUETO P，MCTURK E，ALLERHAND M，et al. Identification and machine learning prediction of knee-point and knee-onset in capacity degradation curves of lithium-ion cells[J]. Energy and AI，2020，1：100006.

热轧工作辊服役状态在线监测与主动再制造时机在线决策方法研究

Research on On-line Monitoring of Service Status of Hot Rolled Work Rolls and On-line Decision-making Method for Active Remanufacturing

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	胡淇伟, 孙永吉, 张建超, 任新意, 高慧敏, 季策, 黄华贵. 基于纹理特征与集成学习的热轧工作辊表面磨损检测方法研究[J]. 机械工程学报, 2026, 62(6): 111-120.
[2]	李雨露, 李俊峰, 万章艺, 魏正英. 基于YOLO算法的激光粉末床熔融成形层形貌分类识别与成形质量预测研究[J]. 机械工程学报, 2026, 62(3): 218-234.
[3]	裴雪武, 李新宇, 高亮, 高艺平, 陈志敏. 复合故障退化情形下基于自适应非线性状态估计的装备状态监测健康指标[J]. 机械工程学报, 2025, 61(3): 119-129.
[4]	宋守许, 蔚辰, 李想, 徐瑞. 再制造工作辊热轧退化脉冲涡流在线监测方法研究[J]. 机械工程学报, 2023, 59(13): 228-237.
[5]	刘巍, 陈启航, 梁冰, 张洋. 基于多源参量感知的航空工装定位器在线监测方法与系统研究[J]. 机械工程学报, 2023, 59(12): 162-172.
[6]	黄永刚, 雷文骞, 陈伟, 王棋, 余华. 适用于输电线路监测的自供电无线在线监测系统[J]. 机械工程学报, 2022, 58(20): 83-91.
[7]	周春阳, 李亚锦, 邓光武, 刘英男, 于大洋. 基于多维度分析的换流变预警技术研究与应用[J]. 电气工程学报, 2021, 16(4): 151-158.
[8]	王建新, 李铁军, 朱军, 杜一锦. 低压开关柜运行在线监测和诊断系统设计[J]. 电气工程学报, 2021, 16(4): 189-195.
[9]	王久健, 杨绍普, 刘永强, 文桂林. 一种基于空间卷积长短时记忆神经网络的轴承剩余寿命预测方法[J]. 机械工程学报, 2021, 57(21): 88-95.
[10]	刘佳鑫, 郎业兴, 韦德福, 唐红. 电缆分布式光纤测温装置校验及温度补偿方法研究 ^*[J]. 电气工程学报, 2020, 15(4): 121-127.
[11]	李洪波, 夏春雨, 张杰, 孔宁. 基于元胞自动机的冷轧工作辊表面形貌演变过程仿真与试验研究[J]. 机械工程学报, 2020, 56(3): 207-215.
[12]	柯庆镝, 詹伟, 宋守许, 刘光复. 基于磨损间隙下碰撞能耗模型的发动机曲轴服役-再制造状态分析方法[J]. 机械工程学报, 2019, 55(5): 148-155.
[13]	刘冬生, 张定华, 罗明, 罗欢. 基于PVDF薄膜传感器的薄壁件铣削振动在线监测与分析[J]. 机械工程学报, 2018, 54(17): 116-123.
[14]	刘献礼, 刘强, 岳彩旭, 王力翚, LIANG S Y, 计伟, 高海宁. 切削过程中的智能技术[J]. 机械工程学报, 2018, 54(16): 45-61.
[15]	尤媛, 李洪波, 夏春雨, 孔宁, 张杰, 贾生晖. 冷轧毛化工作辊表面粗糙度衰减过程的试验与数学模型研究[J]. 机械工程学报, 2018, 54(12): 173-183.