支承动刚度对转子系统临界转速的影响及试验验证

doi:10.3901/JME.2023.21.245

机械工程学报 ›› 2023, Vol. 59 ›› Issue (21): 245-255.doi: 10.3901/JME.2023.21.245

扫码分享

支承动刚度对转子系统临界转速的影响及试验验证

罗忠^1,2,3, 刘凯宁^1,2, 刘家希^1,2, 李雷^1,2, 姜广义^1,2

1. 东北大学机械工程与自动化学院沈阳 110819;
2. 东北大学佛山研究生院佛山 528312;
3. 东北大学航空动力装备振动及控制教育部重点实验室沈阳 110819;
4. 中国航发沈阳发动机研究所沈阳 110015

收稿日期:2022-12-08 修回日期:2023-05-05 出版日期:2023-11-05 发布日期:2024-01-15
通讯作者: 罗忠(通信作者)，男，1978年出生，博士，教授，博士研究生导师。主要研究方向为机械动力学与控制、模型实验理论与方法。E-mail：zhluo@mail.neu.edu.cn
作者简介:刘凯宁，男，1997年出生，硕士研究生。主要研究方向为转子支承系统建模及支承动刚度的影响分析。E-mail：knightleo1997@qq.com
基金资助:
国家自然科学基金(11872148,U1908217)和广东省粤佛联合重点基金(2020B1515120015)资助项目。

Influence of Dynamic Stiffness of Support on Critical Speed of Rotor System and Experimental Verification

LUO Zhong^1,2,3, LIU Kaining^1,2, LIU Jiaxi^1,2, LI Lei^1,2, JIANG Guangyi^1,2

1. School of Mechanical Engineering & Automation, Northeastern University, Shenyang 110819;
2. Foshan Graduate School of Northeastern University, Northeastern University, Foshan 528312;
3. Key Laboratory of Vibration and Control of Aero-Propulsion System Ministry of Education, Northeastern University, Shenyang 110819;
4. AECC Shenyang Engine Research Institute, Shenyang 110015

Received:2022-12-08 Revised:2023-05-05 Online:2023-11-05 Published:2024-01-15

摘要/Abstract

摘要： 支承动刚度对转子系统的临界转速等固有特性影响很大，但其影响规律及程度研究尚不深入，研究动刚度对临界转速的影响规律，提出用动刚度影响判断指数表征动刚度影响程度。首先，建立了考虑支承动刚度的转子系统动力学模型。然后，分析了支承动刚度对临界转速的影响及其不同参数对应的影响规律。结果表明，支承动刚度可导致临界转速降低并出现新的共振峰，且动刚度对临界转速的影响程度与初始支承刚度呈正相关，与转轴长度、转盘质量呈负相关。最后，提出了动刚度影响判断指数可用于动刚度影响程度定量表征，通过数值算例与试验研究对所提动刚度影响判断指数进行验证，数值与试验研究均验证了动刚度影响判断指数的有效性。

关键词: 转子系统, 支承动刚度, 临界转速, 判断指数, 影响规律

Abstract: The dynamic stiffness of support affects the critical speed and inherent characteristics of rotor system greatly, but the research of influence law and influence degree of dynamic stiffness are not thorough. The influence law of dynamic stiffness on the critical speed is studied and the dynamic stiffness influence judgment index is proposed to represent the degree of dynamic stiffness influence. Firstly, the dynamic model of the rotor system considering the dynamic stiffness of the support is established. Then, the influence of dynamic stiffness on critical speed and its vary law under different parameters are analyzed. The dynamic stiffness of the supports may lead to the reduction of the critical speed and the emergence of a new resonance peak. The influence effect of dynamic stiffness is positively correlated with the initial support stiffness, but negatively correlated with the length of the shaft and the mass of the disk. Finally, the dynamic stiffness influence judgment index is proposed for the quantitative characterization of the dynamic stiffness impact degree, and the dynamic stiffness influence judgment index is verified by numerical examples and experimental studies. Both numerical and experimental results verify the validity of the dynamic stiffness influence judgment index.

Key words: rotor system, dynamic support stiffness, critical speed, judgment index, influence law

中图分类号:

V231
TB123

罗忠, 刘凯宁, 刘家希, 李雷, 姜广义. 支承动刚度对转子系统临界转速的影响及试验验证[J]. 机械工程学报, 2023, 59(21): 245-255.

LUO Zhong, LIU Kaining, LIU Jiaxi, LI Lei, JIANG Guangyi. Influence of Dynamic Stiffness of Support on Critical Speed of Rotor System and Experimental Verification[J]. Journal of Mechanical Engineering, 2023, 59(21): 245-255.

参考文献

[1] 洪杰,王华,肖大为,等. 转子支承动刚度对转子动力特性的影响分析[J]. 航空发动机, 2008, 34(1):23-27. HONG Jie, WANG Hua, XIAO Dawei, et al. Analysis of the influence of rotor support dynamic stiffness on rotor dynamic characteristics[J]. Aeroengine, 2008, 34(1):23-27.
[2] KIM S G, JANG S H, HWANG H Y, et al. Analysis of dynamic characteristics and evaluation of dynamic stiffness of a 5-axis multi-tasking machine tool by using FEM and exciter test[C]//International Conference on Smart Manufacturing Application, 2008, Goyangi, Korea, 563-567.
[3] OOI L E, RIPIN Z M. Dynamic stiffness and loss factor measurement of engine rubber mount by impact test[J]. Materials & Design, 2011, 32(4):1880-1887.
[4] TAO Jianfeng, LEI Junbo, LIU Chengliang, et al. Nonlinear static and dynamic stiffness characteristics of support hydraulic system of TBM[J]. Chinese Journal of Mechanical Engineering, 2019, 32(6):36-44.
[5] GUPTA T C. Parametric studies on dynamic stiffness of ball bearings supporting a flexible rotor[J]. Journal of Vibration and Control, 2019, 25(15):2175-2188.
[6] 肖世富,陈红永. Jeffcott刚性支承转子系统的稳定性与动刚度分析[J]. 应用力学学报, 2021, 38(4):1663-1669. XIAO Shifu, CHEN Hongyong. Stability and dynamic stiffness analysis of Jeffcott rigid support rotor system[J]. Chinese Journal of Applied Mechanics, 2021, 38(4):1663-1669.
[7] 鲁鹏,廖明夫,李明. 一种动刚度的测试方法及其在动平衡中的应用[J]. 噪声与振动控制, 2014, 34(2):207-211. LU Peng, LIAO Mingfu, LI Ming. A test method of dynamic stiffness and its application in dynamic balance[J]. Noise and Vibration Control, 2014, 34(2):207-211.
[8] 雷杰,雷晓波,房剑锋,等. 基于不平衡响应的转子动刚度测量方法[J]. 机械设计与研究, 2019, 35(2):142-146. LEI Jie, LEI Xiaobo, FANG Jianfeng, et al. Rotor dynamic stiffness measurement method based on unbalanced response[J]. Machine Design and Research, 2019, 35(2):142-146.
[9] 杜兆刚,张艳春,刘少权. Ms9001e燃气轮机轴承支座结构动刚度测试研究[J]. 燃气轮机技术, 2010, 23(1):30-33. DU Zhaogang, ZHANG Yanchun, LIU Shaoquan. Research on dynamic stiffness test of bearing support structure of MS9001E gas turbine[J]. Gas Turbine Technology, 2010, 23(1):30-33.
[10] 赵文涛,陈果,李琼,等. 航空发动机机匣支承动刚度有限元计算及验证[J]. 航空计算技术, 2011, 41(5):34-38. ZHAO Wentao, CHEN Guo, LI Qiong, et al. Finite element calculation and verification of dynamic stiffness of aero-engine casing support[J]. Aeronautical Computing Technology, 2011, 41(5):34-38.
[11] HONG Jie, CHEN Meng, LIU Shuguo, et al. Application of whole engine finite element models in aero-engine rotordynamic simulation analysis[C]//Proceedings of the ASME Turbo Expo, 2007, Montreal, Canada. ASME, 2007:771-778.
[12] SONG Huiying, WANG Shaohui, SUN Kai. Rotordynamic characteristics analysis for an aero-engine low pressure rotor rig test model[C]//International Conference on Mechanical, Material and Aerospace Engineering, 2018, Wuhan, China. MATEC Web of Conferences, 2018.
[13] 龙伦,吕彪,袁巍. 支承动刚度对某涡轴发动机燃气发生器转子临界转速影响分析[J]. 风机技术, 2018, 60(2):66-70. LONG Lun, LÜ Biao, YUAN Wei. Analysis of the influence of supporting dynamic stiffness on the critical speed of a turboshaft engine gas generator rotor[J]. Fan Technology, 2018, 60(2):66-70.
[14] 姜彦翠,刘献礼,吴石,等. 考虑结合面和轴向力的主轴系统动力学特性[J]. 机械工程学报, 2015, 51(19):66-74. JIANG Yancui, LIU Xianli, WU Shi, et al. Dynamic characteristics of spindle system considering joint surface and axial force[J]. Journal of Mechanical Engineering, 2015, 51(19):66-74.
[15] 陈果. 航空发动机整机振动耦合动力学模型及其验证[J]. 航空动力学报, 2012, 27(2):241-254. CHEN Guo. Vibration coupling dynamics model of aero-engine and its verification[J]. Journal of Aeronautical Dynamics, 2012, 27(2):241-254.
[16] 罗忠,王晋雯,韩清凯,等. 组合支承转子系统动力学的研究进展[J]. 机械工程学报, 2021, 57(7):44-60. LUO Zhong, WANG Jinwen, HAN Qingkai, et al. Research progress in dynamics of combined supported rotor systems[J]. Journal of Mechanical Engineering, 2021, 57(7):44-60.
[17] 李雷,罗忠,何凤霞,等. 考虑变幂数的畸变动力学相似实验模型设计方法及实验研究[J]. 机械工程学报, 2020, 56(23):107-117. LI Lei, LUO Zhong, HE Fengxia, et al. Design method and experimental research of similar experimental model for distortion dynamics considering variable powers[J]. Journal of Mechanical Engineering, 2020, 56(23):107-117.
[18] 李里. 转子系统的动力学建模与分析[D]. 北京:华北电力大学, 2017. LI Li. Dynamic modeling and analysis of rotor system[D]. Beijing:North China Electric Power University, 2017.
[19] LUO Zhong, LI Lei, YANG Yang, et al. Experimental and numerical investigations on novel models for mechanical behaviors of the elastic ring in aero-engine[J]. Proceedings of the Institution of Mechanical Engineers, Part C:Journal of Mechanical Engineering Science, 2021, 235(22):1-11.
[20] ZHANG Wei, DING Qian. Elastic ring deformation and pedestal contact status analysis of elastic ring squeeze film damper[J]. Journal of Sound and Vibration, 2015, 346:314-327.

支承动刚度对转子系统临界转速的影响及试验验证

Influence of Dynamic Stiffness of Support on Critical Speed of Rotor System and Experimental Verification

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	罗忠, 石宝龙, 吴法勇, 李玉奇, 刘凯宁, 张小霞. 考虑装配工艺的螺栓连接转子系统振动特性研究[J]. 机械工程学报, 2024, 60(8): 396-406.
[2]	潘鑫, 张馨, 卢加乔, 吴海琦. 基于超声电机精稳调控的转子不平衡自愈执行装置设计与试验研究[J]. 机械工程学报, 2024, 60(4): 449-457.
[3]	孙凯, 罗忠, 李雷, 葛向东, 郑思佳. 带弹性环式挤压油膜阻尼器转子系统装配特性及试验研究[J]. 机械工程学报, 2023, 59(23): 118-131.
[4]	刘聪, 杨海, 杨哲夫, 洪杰, 王永锋. 基于应变能分布的高速转子系统动力特性设计[J]. 机械工程学报, 2023, 59(17): 136-147.
[5]	贾思祥, 孙丁一, 毛刚, 李永波. 基于对抗熵的转子系统跨工况故障诊断方法[J]. 机械工程学报, 2023, 59(15): 110-120.
[6]	樊赛生, 郭峰, 荆兆刚, 栗心明, 刘海超, POLL G. 硬脂酸吸附对轴承限量供油润滑影响[J]. 机械工程学报, 2023, 59(15): 197-203.
[7]	罗忠, 刘家希, 李雷, 吴法勇, 葛向东. 弹性环配合紧度对转子动力学特性的影响[J]. 机械工程学报, 2023, 59(13): 124-132.
[8]	李莎, 吕延军, 罗宏博, 张永芳, 石瑞. 轴向槽气体轴承-转子非线性系统的动力学行为[J]. 机械工程学报, 2022, 58(7): 103-116.
[9]	高朋, 侯磊, 陈予恕. 双转子系统中介轴承的动载荷及其对轴承温度的影响[J]. 机械工程学报, 2022, 58(5): 87-97.
[10]	熊万里, 汪剑, 陈振宇, 孙文彪, 薛海南, 汤秀清. 箔片气体动压轴承研究进展综述[J]. 机械工程学报, 2022, 58(21): 92-113.
[11]	李志农, 陈世尧, 乔芳, 周世健, 王冬. 盘轴过盈力不足-支座松动耦合故障的转子系统的振动特性研究[J]. 机械工程学报, 2022, 58(11): 109-119.
[12]	罗忠, 王晋雯, 韩清凯, 王德友. 组合支承转子系统动力学的研究进展[J]. 机械工程学报, 2021, 57(7): 44-60.
[13]	谢小柱, 朱裔良, 黄亚军, 申超, 彭清发, 王鹏超, 龙江游. 飞秒激光无碎屑加工不锈钢血管支架[J]. 机械工程学报, 2021, 57(5): 251-261.
[14]	冯坤, 王旌硕, 左彦飞, 江志农. 含轴承间隙的转子非对称支承等效力学特性模拟分析方法[J]. 机械工程学报, 2021, 57(19): 138-146.
[15]	雷群, 袁雅阁, 杜建军, 李立毅. 飞刀铣削中高速气浮电主轴转子动态特性研究[J]. 机械工程学报, 2021, 57(13): 45-54.