一种梁式管接头密封性能与结构参数敏感性分析

doi:10.3901/JME.2021.03.147

机械工程学报 ›› 2021, Vol. 57 ›› Issue (3): 147-155.doi: 10.3901/JME.2021.03.147

扫码分享

一种梁式管接头密封性能与结构参数敏感性分析

崔颖¹, 于颖嘉¹, 王永亮¹, 赵爽², 钟兢军³

1. 大连海事大学船舶与海洋工程学院大连 116026;
2. 中国航空发动机集团沈阳发动机研究所沈阳 110015;
3. 上海海事大学商船学院上海 201306

收稿日期:2020-03-21 修回日期:2020-09-27 出版日期:2021-02-05 发布日期:2021-03-16
通讯作者: 于颖嘉(通信作者),男,1990年出生,博士研究生。主要研究方向为金属静密封接触力学与振动控制。E-mail:cf_yuyingjia@sina.com
作者简介:崔颖,女,1977年出生,博士,副教授。主要研究方向为转子动力学、管路连接结构密封接触力学。E-mail:cuiying@dlmu.edu.cn
基金资助:
教育部人文社科（18YJA880010）和国家自然科学基金青年基金（51606023）资助项目。

Sealing Performance and Sensitivity Analysis of Structure Parameters for a New Beam Seal

CUI Ying¹, YU Yingjia¹, WANG Yongliang¹, ZHAO Shuang², ZHONG Jingjun³

1. College of Naval Architecture and Ocean Engineering, Dalian Maritime University, Dalian 116026;
2. Shenyang Engine Design Institute, Aero Engine Corporation of China, Shenyang 110015;
3. College of Merchant Marine, Shanghai Maritime University, Shanghai 201306

Received:2020-03-21 Revised:2020-09-27 Online:2021-02-05 Published:2021-03-16

摘要/Abstract

摘要： 梁式管接头具有耐高压、自紧性和自封性等优点，在航空液压系统中有着广阔的应用前景。设计提出了一种带有椭圆形凹槽的梁式管接头阴接头结构，建立了该型梁式管接头的弹塑性有限元接触模型，数值模拟得到该结构能够形成两道有效密封。以最大接触压力为密封性能评价指标的分析表明，管内流体压力具有提高梁式管接头密封性能的作用，且施加的预紧力存在一个最佳设计值。该型梁式管接头阴、阳接头配合面在不同预紧力下的接触带宽试验结果与数值模拟结果吻合较好，验证了有限元模型和分析方法的有效性。进而，采用正交试验对梁式管接头的主要结构参数进行分析，利用极差法得到了结构参数对两道密封带密封性能影响的敏感性。结果表明，椭圆形凹槽的长轴和短轴，第一道密封的名义接触带宽与U形梁截面宽度对带有椭圆形凹槽的梁式管接头密封性能有显著影响。

关键词: 梁式管接头, 弹塑性有限元, 密封性能, 敏感性, 正交试验

Abstract: The beam seal has a broad application prospect in the aviation hydraulic system due to its high-pressure resistance, self-tightening and self-sealing features. A type of female joint structure with elliptical groove is proposed. The elastic-plastic finite element contact model of the beam seal is established. The analysis with the maximum contact pressure as the evaluation index of sealing performance shows that the fluid pressure in the pipe can improve the sealing performance of the beam seal, and there is an optimal design value for the applied pre-tightening force. The experimental results of the contact bandwidth on the mating surfaces of the female and male joints under different pre-tightening force are in good agreement with the numerical simulation, which verifies the effectiveness of the finite element model and analysis method. Furthermore, the main structural parameters of the beam seal are analyzed by orthogonal array method, and the sensitivity of the structural parameters to the sealing performance of the two sealing is obtained by the range method. It is found that the long and short axis of the elliptical groove, the nominal contact bandwidth of the first seal and the section width of the U-shaped beam have significant influence on the sealing performance of the beam seal.

Key words: beam seal, elastic-plastic finite element, sealing performance, sensitivity, orthogonal array method

中图分类号:

V231

崔颖, 于颖嘉, 王永亮, 赵爽, 钟兢军. 一种梁式管接头密封性能与结构参数敏感性分析[J]. 机械工程学报, 2021, 57(3): 147-155.

CUI Ying, YU Yingjia, WANG Yongliang, ZHAO Shuang, ZHONG Jingjun. Sealing Performance and Sensitivity Analysis of Structure Parameters for a New Beam Seal[J]. Journal of Mechanical Engineering, 2021, 57(3): 147-155.

参考文献

[1] 付长安,宋治国. 超高压飞机液压系统的密封问题[J]. 润滑与密封,2000(4):5-6. FU Changan,SONG Zhiguo. Sealing problem of hydraulic system of ultra-high pressure aircraft[J]. Lubrication Engineering,2000(4):5-6.
[2] 康泽天,周博,薛世峰. 形状记忆合金管接头热机耦合行为的有限单元法[J]. 机械工程学报,2018,54(18):68-75. KANG Zetian,ZHOU Bo,XUE Shifeng. Finite element numerical simulation on thermo-mechanical coupling behavior in shape memory alloy pipe connection[J]. Journal of Mechanical Engineering,2018,54(18):68-75.
[3] 王小刚,张方晓,黄鹏. 基于ANSYS的管路锥形密封结构参数分析[J]. 兵工自动化,2009,28(8):25-27. WANG Xiaogang,ZHANG Fangxiao,HUANG Peng. Analysis of parameters of pipeline cone sealing structures based on ANSYS[J]. Ordnance Industry Automation,2009,28(8):25-27.
[4] 韩冲,张勇. 导管连接件球头-锥面结构密封性能研究[J]. 润滑与密封,2012(10):105-112. HAN Chong,ZHANG Yong. Research on sealing property of globe-cone joint for pipeline[J]. Lubrication Engineering,2012(10):105-112.
[5] 翟富刚,孙玉岗,豆旭安,等. 某超高压管接头结构参数对接触密封性能的影响分析[J]. 液压与气动,2017(6):60-64. ZHAI Fugang,SUN Yugang,DOU Xuan,et al. Influence of structural parameters on sealing performance of ultra-high pressure pipe joint[J]. Chinese Hydraulics & Pneumatics,2017(6):60-64.
[6] 欧阳小平,方旭,朱莹,等. 航空液压管接头综述[J]. 中国机械工程,2015,26(16):2262-2271. OUYANG Xiaoping,FANG Xu,ZHU Ying,et al. Overview of aviation hydraulic fitting[J]. China Mechanical Engineering,2015,26(16):2262-2271.
[7] AS4207A Fitting End,External thread,beam seal,design standard[S]. Warrendale,PA:SAE,1996.
[8] AS4209B Fitting End Assembly,internal thread,retained nut,beam seal,design standard[S]. Warrendale,PA:SAE,1997.
[9] JEON J Y,KIM B T. A study on contact characteristics by the geometry variation of beam seal fitting of an aircraft fuel hose[J]. Journal of the Korean Society of Manufacturing Process Engineers,2013,12(6):101-108.
[10] 李晓东. 可分离式航空液压管接头密封特性研究[D]. 大连:大连理工大学,2018. LI Xiaodong. Sealing performance of separable aviation hydraulic fittings[D]. Dalian:Dalian University of Technology,2018.
[11] SALANT R F,MASER N,YANG B. Numerical model of a reciprocating hydraulic rod seal[J]. Journal of Tribology,2006,129(1):91-97.
[12] SHI Fanghui,SALANT R F. Numerical study of a rotary lip seal with a quasi-random sealing surface[J]. Journal of Tribology,2001,123(3):517-525.
[13] YANG B,SALANT R F. A numerical model of a reciprocating rod seal with a secondary lip[J]. Tribology Transactions,2008,51(2):119-127.
[14] 高连新,金烨,张居勤. 石油套管特殊螺纹接头的密封设计[J]. 机械工程学报,2005,41(3):216-220. GAO Lianxi,JIN Ye,ZHANG Juqin. Seal design of premium threaded casing connections[J]. Journal of Mechanical Engineering,2005,41(3):216-220.
[15] TAGUCHI G,CHOWDHURY S,WU Y. Taguchi's quality engineering handbook[M]. Hoboken:John Wiley,2005.
[16] JIA Xiaohong,GUO Fei,SALANT R F,et al. Parameter analysis of the radial lip seal by orthogonal array method[J]. Tribology International,2013,64:96-102.
[17] HU Chaobin,ZHANG Xiaobing. Influence of multiple structural parameters on interior ballistics based on orthogonal test methods[J]. Defence Technology,2019,56(4):201-208.

一种梁式管接头密封性能与结构参数敏感性分析

Sealing Performance and Sensitivity Analysis of Structure Parameters for a New Beam Seal

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	魏永峭, 张晋, 王少江, 漆小虎, 郭瑞, 杨海江. 变双曲圆弧齿线圆柱齿轮传动界面磨损规律及敏感性分析[J]. 机械工程学报, 2024, 60(5): 81-94.
[2]	张涵寓, 宋周洲, 刘钊, 朱平. 碳纤维复合材料与铝合金胶铆混合连接力学性能可靠性研究[J]. 机械工程学报, 2023, 59(24): 334-343.
[3]	吴锦辉, 张德权, 韩旭. 工业机器人参数容差稳健性设计[J]. 机械工程学报, 2023, 59(11): 147-158.
[4]	王朋朋, 刘佳, 王峰, 马小飞. 大口径高精度星载天线的热变形优化设计与仿真计算[J]. 机械工程学报, 2022, 58(9): 41-48.
[5]	杨超, 叶伟, 陈巧红. 并联机构敏感性分析和多目标优化设计方法[J]. 机械工程学报, 2022, 58(19): 229-241.
[6]	陈巍巍, 石文泽, 卢超, 程进杰, 陈尧, 陈果. 高温锻件在线快速检测螺旋线圈EMAT优化设计[J]. 机械工程学报, 2022, 58(10): 12-23.
[7]	王建磊, 门川皓, 赵伟刚, 贾谦, 崔亚辉, 张琛, 袁小阳. 动静压机械密封的结构设计及端面槽型优化研究[J]. 机械工程学报, 2021, 57(9): 108-117.
[8]	陈志平, 焦鹏, 马赫, 顾亚楠, 葛鹏. 基于初始缺陷敏感性的轴压薄壁圆柱壳屈曲分析研究进展[J]. 机械工程学报, 2021, 57(22): 114-129.
[9]	匡柯, 孙跃东, 任东生, 韩雪冰, 郑岳久, 耿兆杰. 车用锂离子电池电化学-热耦合高效建模方法[J]. 机械工程学报, 2021, 57(14): 10-22.
[10]	张少哲, 戴海峰, 袁浩, 明平文, 魏学哲. 质子交换膜燃料电池电化学阻抗谱敏感性研究[J]. 机械工程学报, 2021, 57(14): 40-51.
[11]	许灿, 朱平, 刘钊. 平纹机织碳纤维复合材料多尺度随机力学性能层次敏感性[J]. 机械工程学报, 2021, 57(14): 213-222.
[12]	刘宗超, 吴林辉, 陈贡发. 几何参数对主动脉支架生物力学性能的影响[J]. 机械工程学报, 2021, 57(11): 112-119.
[13]	宫岛, 刘广宇, 周劲松, 孙煜, 尤泰文. 动车组车体异常振动问题分析及治理研究[J]. 机械工程学报, 2021, 57(10): 95-105,117.
[14]	李雷, 罗忠, 何凤霞, 张文笛. 考虑变幂数的畸变动力学相似试验模型设计方法及试验研究[J]. 机械工程学报, 2020, 56(23): 107-117.
[15]	刘可心, 王蕾, 刘佳磊, 金松哲. Ti₂AlN薄膜的制备及性能表征[J]. 机械工程学报, 2019, 55(16): 77-84.