基于柔性并联连续体的灵巧操作手的设计及分析

doi:10.3901/JME.2020.19.122

机械工程学报 ›› 2020, Vol. 56 ›› Issue (19): 122-131.doi: 10.3901/JME.2020.19.122

• 特邀专栏：纪念张启先院士诞辰95周年 • 上一篇下一篇

扫码分享

基于柔性并联连续体的灵巧操作手的设计及分析

汪培义, 郭盛, 王向阳, 宋马军, 林华杰

北京交通大学机械与电子控制工程学院北京 100044

收稿日期:2020-02-21 修回日期:2020-05-06 出版日期:2020-10-05 发布日期:2020-11-17
通讯作者: 郭盛(通信作者),男,1972年出生,博士,教授,博士研究生导师。主要研究方向为机器人机构学。E-mail:shguo@bjtu.edu.cn
作者简介:汪培义,男,1995年出生,博士研究生。主要研究方向为机器人机构学和连续体机器人。E-mail:19116019@bjtu.edu.cn
基金资助:
国家自然科学基金（51875033）和北京市自然科学基金（L172021）资助项目。

Design and Analysis of a Dexterous Gripper Based on Flexible Parallel Continuum Manipulator

WANG Peiyi, GUO Sheng, WANG Xiangyang, SONG Majun, LIN Huajie

School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044

Received:2020-02-21 Revised:2020-05-06 Online:2020-10-05 Published:2020-11-17

摘要/Abstract

摘要： 提出了一种新型4-DOF柔性并联连续体机构，将该机构与末端绳驱动的抓手相结合，设计完成具有灵活抓取性能的操作手。将该柔性机构通过柔性支链等效的方式等效为传统刚性连杆的并联机构，并且运用螺旋理论对该机构进行自由度分析；采用经典的Cosserat Rod模型对机构进行运动学建模；通过对比分析三种并联连续体机构的可操作度，4-DOF并联连续体机构由于具有一个额外的扭转自由度，使得操作手能够更加灵活地抓取物体，在此基础上给出了一组操作手抓取的仿真实例。最后通过试验验证机构自由度以及运动学模型的数值解，并且实现操作手灵活抓取的性能。

关键词: 并联连续体机构, Cosserat Rod模型, 操作手, 灵活抓取, 运动可操作度

Abstract: A new four-degree-of-freedom parallel continuum manipulator is presented, which was combined with a cable-driven gripper to improve the performance of dexterous grasp. This manipulator is approximately equivalent to the traditional rigid link parallel mechanism by complaint branch equivalent method, and the degree of freedom analysis of the manipulator is performed by using the screw theory. The classic Cosserat Rod model is applied to model the kinematics of the continuum manipulator. By comparative analysis among three types of parallel continuum manipulator, the proposed manipulator can provide an additional torsional movement which make the gripper grasp the object more flexibly. Based on this, a simulation example of dexterous grasp is given. Finally, experiments verify the degree of freedom and kinematics of the manipulator and the performance of flexible grasping of the gripper.

Key words: parallel continuum manipulator, Cosserat Rod model, gripper, flexible grasp, kinematic manipulability

中图分类号:

TG156

汪培义, 郭盛, 王向阳, 宋马军, 林华杰. 基于柔性并联连续体的灵巧操作手的设计及分析[J]. 机械工程学报, 2020, 56(19): 122-131.

WANG Peiyi, GUO Sheng, WANG Xiangyang, SONG Majun, LIN Huajie. Design and Analysis of a Dexterous Gripper Based on Flexible Parallel Continuum Manipulator[J]. Journal of Mechanical Engineering, 2020, 56(19): 122-131.

参考文献

[1] WEBSTER R J,JONES B A. Design and kinematic modeling of constant curvature continuum robots:A review[J]. The International Journal of Robotics Research,2010,29(13):1661-1683.
[2] BRYSON C E,RUCKER D C. Toward parallel continuum manipulators[C]//2014 IEEE International Conference on Robotics and Automation (ICRA). IEEE,2014:778-785.
[3] 于靖军,郝广波,陈贵敏,等. 柔性机构及其应用研究进展[J]. 机械工程学报,2015,51(13):53-68. YU Jingjun,HAO Guangbo,CHEN Guimin,et al. State-of-art of compliant mechanisms and their applications[J]. Journal of Mechanical Engineering. 2015,51(13):53-68.
[4] SIMAAN N,TAYLOR R,FLINT P,et al. A dexterous system for laryngeal surgery[C]//Proceeding of 2004 IEEE International Conference on Robotics and Automation,2004:351-357.
[5] 徐凯,刘欢. 多杆连续体机构:构型与应用[J]. 机械工程学报,2018,54(13):25-33. XU Kai,LIU Huan. Multi-backbone continuum mechanisms:Forms and applications[J]. Journal of Mechanical Engineering,2018,54(13):25-33.
[6] ZHAO J R,ZHENG X D,ZHENG M H,et al. An endoscopic continuum testbed for finalizing system characteristics of a surgical robot for NOTES procedures[C]//2013 IEEE/ASME International Conference on Advanced Intelligent Mechatronics. IEEE,2013:63-70.
[7] XU K,ZHAO J R,FU M X. Development of the SJTU unfoldable robotic system (SURS) for single port laparoscopy[J]. IEEE/ASME Transactions on Mechatronics,2014,20(5):2133-2145.
[8] LIU S T,YANG Z X,ZHU Z J,et al. Development of a dexterous continuum manipulator for exploration and inspection in confined spaces[J]. Industrial Robot:An International Journal,2016,43(3):284-295.
[9] XU K,ZHAO J R,QIU D,et al. A pilot study of a continuum shoulder exoskeleton for anatomy adaptive assistances[J]. Journal of Mechanisms and Robotics,2014,6(4):041011.
[10] XU K,WANG Y,YANG Z X. Design and preliminary experimentation of a continuum exoskeleton for self-provided bilateral rehabilitation[C]//2014 IEEE International Conference on Information and Automation (ICIA). IEEE,2014:327-332.
[11] LIU H,ZHANG Z Y,DONG T L,et al. A single-actuator gripper with a working mode switching mechanism for grasping and rolling manipulation[C]//2018 IEEE/ASME International Conference on Advanced Intelligent Mechatronics (AIM). IEEE,2018:359-364.
[12] XU K,LIU H,ZHANG Z,et al. Wrist-powered partial hand prosthesis using a continuum whiffle tree mechanism:A case study[J]. IEEE Transactions on Neural Systems and Rehabilitation Engineering,2018,26(3):609-618.
[13] YANG Z,ZHU X,XU K. Continuum Delta Robot:a Novel Translational Parallel Robot with Continuum Joints[C]//2018 IEEE/ASME International Conference on Advanced Intelligent Mechatronics (AIM). IEEE,2018:748-755.
[14] FESTO. Bionic Tripod 3.0.[EB/OL]. https://www.festo.com/group/en/cms/10240.htm,2011.
[15] TILL J,ALOI V,RUCKER C. Real-time dynamics of soft and continuum robots based on Cosserat rod models[J]. The International Journal of Robotics Research,2019,38(6):723-746.
[16] OREKHOV A L,BRYSON C E,TILL J,et al. A surgical parallel continuum manipulator with a cable-driven grasper[C]//2015 37 th Annual International Conference of the IEEE Engineering in Medicine and Biology Society (EMBC). IEEE,2015:5264-5267.
[17] YOUNG E M,KUCHENBECKER K J,GERLING G. Design of a parallel continuum manipulator for 6-DoF fingertip haptic display[C]//2017 IEEE World Haptics Conference (WHC). IEEE,2017:599-604.
[18] YOUNG E M,KUCHENBECKER K J. Implementation of a 6-DOF parallel continuum manipulator for delivering fingertip tactile cues[J]. IEEE Transactions on Haptics,2019,12(3):295-306
[19] 方跃法,林华杰. 连续体并联抓取机器人的结构设计及运动学分析[J]. 北京交通大学学报,2019,43(4):80. FANG Yuefa,LIN Huajie. Structural designand kinematics analysis of the continuum parallel grasping manipulator[J]. Journal of Beijing Jiaotong University,2019,43(4):80.
[20] WU G L,SHI G L. Experimental statics calibration of a multi-constraint parallel continuum robot[J]. Mechanism and Machine Theory,2019,136:72-85.
[21] 陈子明,张扬,黄坤,等. 一种无伴随运动的对称两转一移并联机构[J]. 机械工程学报,2016,52(3):9-17. CHEN Ziming,ZHANG Yang,HUANG Kun,et al. Symmetrical 2R1T parallel mechanism without parasitic motion[J]. Journal of Mechanical Engineering,2016,52(3):9-17.
[22] JONES B A,GRAY R L,TURLAPATI K. Three dimensional statics for continuum robotics[C]//2009 IEEE/RSJ International Conference on Intelligent Robots and Systems. IEEE,2009:2659-2664.
[23] ANTMAN S S,MARSDEN J E,SIROVICH L. Nonlinear problems of elasticity[M]. 2nd ed. New York:Springer,2005
[24] YOSHIKAWA T. Manipulability of robotic mechanisms[J]. The international journal of Robotics Research,1985,4(2):3-9.

基于柔性并联连续体的灵巧操作手的设计及分析

Design and Analysis of a Dexterous Gripper Based on Flexible Parallel Continuum Manipulator

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	方续东, 邓武彬, 吴祖堂, 李进, 吴晨, 前田龙太郎, 田边, 赵立波, 林启敬, 张仲恺, 韩香广, 蒋庄德. 基于惯性传感器的呼吸测量技术综述[J]. 机械工程学报, 2024, 60(20): 1-23.
[2]	傅杨, 张跃, 毛颖, 唐小华, 陈祖高, 徐和武, 杨雨沛, 高斌, 田贵云. 基于Feature Boosting的管道电磁内检测多传感信号缺陷解析算法[J]. 机械工程学报, 2024, 60(20): 51-67.
[3]	吴洁, 沈以赴, 黄国强. 2024铝合金填丝TIG焊接头搅拌摩擦加工组织和性能研究[J]. 机械工程学报, 2024, 60(20): 153-161.
[4]	张志勇, 王宇翔, 黄彩霞, 吴悠, 杜荣华. 融合灰色预测和卡尔曼滤波的车辆侧向碰撞预警[J]. 机械工程学报, 2024, 60(20): 240-250.
[5]	廖贵文, 张毅, 魏凯, 刘小君, 王伟. 受限润滑界面液固二相流场结构与颗粒运动行为耦合特性分析[J]. 机械工程学报, 2024, 60(20): 351-360.
[6]	王旭, 姜兴宇, 杨国哲, 孙猛, 于沈弘, 毕凯航, 赵日铮, 刘伟军. 基于PSO-SSA的激光清洗装备人机界面布局优化研究[J]. 机械工程学报, 2024, 60(20): 372-387.
[7]	王德祥, 张宇, 江京亮, 刘新福, 刘国梁. 离子液基和棕榈油基纳米流体在镍基高温合金微量润滑磨削界面的摩擦学机理研究[J]. 机械工程学报, 2024, 60(19): 159-171.
[8]	李浦, 逯代兴. 协同仿真算法研究综述[J]. 机械工程学报, 2024, 60(19): 172-186.
[9]	王晓宇, 魏兆成, 王学勤, 王栋. 整体叶轮双列开槽五轴插铣加工的残留材料建模[J]. 机械工程学报, 2024, 60(19): 310-317.
[10]	王高见, 刘丽, 康丹丹, 叶延洪, 邓德安. Ni含量对高速列车转向架耐候钢焊缝金属微观组织、力学性能及腐蚀行为的影响[J]. 机械工程学报, 2024, 60(18): 163-172.
[11]	张明康, 师文庆, 徐梅珍, 王迪, 陈杰. 隐式曲面多孔结构压缩性能与流体压降性能研究[J]. 机械工程学报, 2024, 60(18): 394-406.
[12]	马伟佳, 朱小龙, 刘青瑶, 段星光, 李长胜. 人工智能在机器人辅助手术中的应用[J]. 机械工程学报, 2024, 60(17): 22-39.
[13]	袁小庆, 吴涛, 原勋, 王文东. 基于GSO-RF意图识别算法的全身助力外骨骼控制方法研究[J]. 机械工程学报, 2024, 60(17): 91-101.
[14]	张禹泽, 赵竞夫, 赵振伟, 康荣杰, 戴建生, 宋智斌. 面向多关节训练的并联柔索驱动下肢康复机器人设计与分析[J]. 机械工程学报, 2024, 60(17): 111-122.
[15]	梁旭, 张建勇, 李国涛, 苏婷婷, 何广平, 侯增广. 面向骨折复位手术的冗余并联机构：设计、建模与性能分析[J]. 机械工程学报, 2024, 60(17): 133-146.