节流配汽超超临界汽轮机调门特性与经济运行

doi:10.3901/JME.2018.22.168

机械工程学报 ›› 2018, Vol. 54 ›› Issue (22): 168-176.doi: 10.3901/JME.2018.22.168

• 可再生能源与工程热物理 • 上一篇下一篇

扫码分享

节流配汽超超临界汽轮机调门特性与经济运行

黄喜军¹, 胥建群¹, 于忠平², 孙剑¹, 张浩峰¹, 陈晓欣¹

1. 东南大学能源热转换及其过程测控教育部重点实验室南京 210096;
2. 大唐南京发电厂南京 210057

收稿日期:2018-01-06 修回日期:2018-05-07 出版日期:2018-11-20 发布日期:2018-11-20
通讯作者: 胥建群(通信作者),男,1959年出生,博士,教授。主要从事汽轮机运行特性与理论建模、热力透平数值模拟等研究。E-mail:qlj1062@163.com
作者简介:黄喜军,男,1991年出生。主要从事热力系统仿真和建模研究。E-mail:happyarmy@foxmail.com

Valve Characteristics and Economic Operation for Steam Distribution Mode of Ultra-supercritical Steam Turbine

HUANG Xijun¹, XU Jianqun¹, YU Zhongping², SUN Jian¹, ZHANG Haofeng¹, CHEN Xiaoxin¹

1. Key Laboratory of Energy Thermal Conversion and Control of Ministry of Education, Southeast University, Nanjing 210096;
2. Datang Nanjing Power Plant, Nanjing 210057

Received:2018-01-06 Revised:2018-05-07 Online:2018-11-20 Published:2018-11-20

摘要/Abstract

摘要： 汽轮机主蒸汽流量是机组性能指标计算的关键参数之一，采用现有调门模型对其计算面临建模繁琐、模型复杂和计算过程参数难以获取等问题。针对有效面积变化的汽轮机高压调门，提出用椭圆公式对其建模，并用公开文献试验数据对其进行验证。结合阀门模型，以某660 MW节流配汽型超超临界汽轮机组为研究对象，对该机组进行变工况计算，研究不同负荷的不同运行策略下，高压缸效率和机组经济性的变化情况。结果表明，椭圆公式能够表现调门变工况特性，该方法建模过程简单，计算方便，在调门工作区域内计算精度高。机组高压缸效率随着高压调门开度的减小而减小，纯滑压运行方式下热耗率最低，但考虑到电网调频要求，建议机组变工况运行时调门开度控制在30%～45%为宜。所推荐的宽范围变工况运行策略在调门调节裕量满足电网调频的要求下，能够提高机组的经济性和深度调峰能力。研究结果可为同类型机组的运行优化策略提供参考。

关键词: 矫圆, 矫直, 平面曲梁, 统一曲率, 往复弯曲, 调门特性, 节流配汽, 经济运行, 椭圆公式

Abstract: The main steam flow rate is one of the key parameters in performance calculation of steam turbine unit. The use of existing steam turbine high pressure governing valve models to calculate the main steam flow rate poses problems such as exhausting modeling, model complexity, and difficulty in obtaining parameters of the calculation process. The valve with variable effective flow area is modeled by elliptic equations and tested with open literature experimental data. Method a calculation model for the off-design performance of a 660 MW ultra supercritical steam turbine unit with steam distribution combined the valve model. Then this unit model is used to explore the efficiency of HP cylinder and the unit's economic under different loads with different operation strategies. Analysis shows that the characteristics which the ellipse equations reflected are consistent with the literature experimental data and this method is simple in computation, high accuracy in work area. The efficiency of the HP cylinder of the unit decreases as the opening degree of the steam turbine high pressure governing valve decreases. The unit heat rate is the lowest when adopting the sliding pressure operation and the valve in 30%-45% opening should be recommended for operation when taking into account the request of frequency adjustment of electric network. The proposed operation strategies can improve the units' economic performance and enhanced the ability of in depth peak load cycling at the request of frequency adjustment of electric network. It provides reference for the operation strategy of similar units.

Key words: Plane curved beam, Reciprocating bending, Setting round process, Straightening process, Uniform curvature, economic operation, elliptic equations, steam distribution, valve characteristics

中图分类号:

TK261

黄喜军, 胥建群, 于忠平, 孙剑, 张浩峰, 陈晓欣. 节流配汽超超临界汽轮机调门特性与经济运行[J]. 机械工程学报, 2018, 54(22): 168-176.

HUANG Xijun, XU Jianqun, YU Zhongping, SUN Jian, ZHANG Haofeng, CHEN Xiaoxin. Valve Characteristics and Economic Operation for Steam Distribution Mode of Ultra-supercritical Steam Turbine[J]. Journal of Mechanical Engineering, 2018, 54(22): 168-176.

参考文献

[1] 中电联规划与统计信息部. 中国电力行业年度发展报告(2017)综述部分发布[EB/OL].[2017-09-11]. http://www.cec.org.cn/guihuayutongji/gongzuodongtai/2017-09-11/172982.html,2017-09-11. China Electricity Council. The annual report on progress towards China's electric power industry(2017)[EB/OL].[2017-09-11]. http://www.cec.org.cn/guihuayutongji/gongzuodongtai/2017-09-11/172982.html,2017-09-11.
[2] 国家发展改革委,国家能源局. 能源发展"十三五"规划[R]. 北京:人民出版社,2016. The National Development and Reform Commission and The National Energy Administration. The 13th Five-Year Plan for Energy Development of the People's Republic of China[R]. Beijing:Chinese People's Publishing House,2016.
[3] MIGUEL A G S,TREVOR K,LUBOS P. Review of the operational flexibility and emissions of gas-and coal-fired power plants in a future with growing renewables[J]. Renewable & Sustainable Energy Reviews,2018,82(1):1497-1513.
[4] KUBIK M L,COKER P J,BARLOW J F. Increasing thermal plant flexibility in a high renewables power system[J]. Applied Energy,2015,154:102-111.
[5] FRANK P,FLORIAN E,FLORIAN K. Flexibility in thermal power plants-with a focus on existing coal-fired power plants[M/OL]. Berlin:Agora Energiewende:2017[2017-06-30]. https://www.agora-energiewende.de/index.php?id=157&tx_agorathemen_themenliste[produkt]=1003&L=1.
[6] MICHAEL W,ANDREAS F,HEIKO L. Steam Turbines for flexible load operation in the future market of power generation[C]//International Gas Turbine Institute. ASME Turbo Expo 2012:Turbine Technical Conference and Exposition,June 11-15,Copenhagen,Denmark,2012. New York:ASME,2012:579-588.
[7] LI Yong,HU Pengfei,CAO Lihau,et al. Solid particle erosion in the reheat stage of the steam turbine[J]. Journal of Mechanical Engineering,2016,52(16):140-147.
[8] CAO Lihau,LIN Aqiang,LI Yong,et al. Optimum tilt angle of flow guide in steam turbine exhaust hood considering the effect of last stage flow field[J]. Chinese Journal of Mechanical Engineering,2017,30(4):866-875.
[9] 胥建群,曹祖庆.汽轮机调速系统和调节级数学模型[J]. 汽轮机技术,1991(1):15-21. XU Jianqun,CAO Zuqing.Turbine speed governor system and the mathematical model of governing stage[J]. Turbine Technology,1991(1):15-21.
[10] FULS W F. Enhancement to the traditional ellipse law for more accurate modeling of a turbine with a finite number of stages[J]. Journal of Engineering for Gas Turbines & Power,2017,139(11):112603-1-12.
[11] KANG S Y,LEE J J,TONG S K,et al. Program development for performance analysis of a steam turbine system with the use of overload valve[J]. Journal of Mechanical Science & Technology,2016,30(12):5759-5769.
[12] 曹祖庆.汽轮机变工况特性[M]. 北京:水利电力出版社,1991. CAO Zuqing. Varying Condition characteristic of steam turbine[M]. Beijing:Water Resources and Electric Power Press,1991.
[13] GIORGIO Z,OTTMAR S,MICHRAL S,et al. Unsteady CFD simulation of control valve in throttling conditions and comparison with experiments[C]//International Gas Turbine Institute. ASME Turbo Expo 2013:Turbine Technical Conference and Exposition. American Society of Mechanical Engineers,June 3-7,2013,San Antonio,Texas,USA. New York:ASME,2013:V05BT25A019-V05BT25A019.
[14] CLEMENS B D,BENRA F K,DOHMEN H J,et al. Numerical investigation on the time-variant flow field and dynamic forces acting in steam turbine inlet valves[J]. Journal of Engineering for Gas Turbines and Power,2015,137(8):081601.
[15] GIORGIO Z,BAUMGARTNER F,RICE T,et al. Experimental and numerical investigation into the aerodynamics of a novel steam turbine valve and its field application[J]. Journal of Engineering for Gas Turbines and Power,2012,136(9):653-664.
[16] ANDREW G,FRAWLEY P. Experimental parametric equation for the prediction of valve coefficient (Cv) for choke valve trims[J]. International Journal of Pressure Vessels and Piping,2011,88(2-3):109-118.
[17] HALIMI B,KIM S H,KUNE Y S. Engineering of combined valve flow for power conversion system[J]. Energy Conversion and Management,2013,65:448-455.
[18] HALIMI B,KUNE Y S. Engineering nonlinearity characteristic compensation for commercial steam turbine control valve using linked MARS code and Matlab Simulink[J]. Nuclear Engineering and Design,2012,243:360-370.
[19] YANG Haisheng,CHANG Shuping,WU Ruitao. Analysis of the sliding pressure operation for throttle controlled steam turbine generation unit[C]//IEEE Power & Energy Society. 2012 Asia-Pacific Power and Energy Engineering Conference,March 27-29,2012,Shanghai,China. Los Alamitos:IEEE,2012:1-4.
[20] 曾江卓,孙禔,潘杨. 基于一次调频能力的节流配汽汽轮机组滑压运行曲线优化[J]. 湖北电力,2016,40(6):37-41. ZENG Jiangzhuo,SUN Ti,PAN Yang. Study on sliding pressure operation curve of throttled steam turbine based on primary frequency regulation[J]. Hubei Electric Power,2016,40(6):37-41.
[21] WECHSUNG M,FELDMULLER A,LEMMEN H. Steam turbines for flexible load operation in the future market of power generation[C]//International Gas Turbine Institute. ASME Turbo Expo 2012:Turbine Technical Conference and Exposition,June 11-15,Copenhagen,Denmark,2012. New York:ASME,2012:579-588.
[22] 施延洲,焦林生,姚啸林,等.超(超)临界汽轮机组滑压运行优化试验[J]. 热力发电,2013,42(12):8-12. SHI Yanzhou,JIAO Linsheng,YAO Xiaolin,et al. Optimization test of sliding pressure operation on large supercritical steam turbine[J]. Thermal Power Generation,2013,42(12):8-12.
[23] 康松,杨建明,胥建群.汽轮机原理[M]. 北京:中国电力出版社,2000. KANG Song,YANG Jianming,XU Jianqun. Steam turbine Principle[M]. Beijing:China Power Press,2000.
[24] 沈维道,童钧耕.工程热力学[M]. 北京:高等教育出版社,2007. SHEN Weidao,DONG Jingeng. Engineering thermodynamics[M]. Beijing:Higher Education Press,2007.
[25] GAMLIN A. Fluid dynamic model tests concerning valve forces[R]. No.TM/TVL/2094/460,Siemens AG,1994.
[26] MA Lin,XU Jianqun,CAO Zuqing. Research on varying condition characteristic of steam turbine governing stage based on dimensional analysis[J]. Proceedings of the CSEE,2014,34(5):778-783.

节流配汽超超临界汽轮机调门特性与经济运行

Valve Characteristics and Economic Operation for Steam Distribution Mode of Ultra-supercritical Steam Turbine

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈洁, 龙英文. 基于PD一致性算法的微电网分层优化控制策略^*[J]. 电气工程学报, 2023, 18(2): 174-182.
[2]	孟庆党, 赵军, 穆振凯, 张玉, 于高潮. 中小型轴类零件旋转弯曲矫直工艺数值模拟研究[J]. 机械工程学报, 2022, 58(22): 208-218.
[3]	于高潮, 赵军. 金属板材循环拉压加载中力学行为的演化[J]. 机械工程学报, 2019, 55(4): 33-41.
[4]	张赵宁, 张杰, 孔宁, 李洪波. 基于拉矫过程参数组合优化的带钢酸洗效率[J]. 机械工程学报, 2019, 55(2): 51-63.
[5]	茆美琴,徐锐. 基于分布式控制的孤岛微网经济调度方法[J]. 电气工程学报, 2018, 13(9): 8-13.
[6]	范沁红, 张洪, 姜雪程. 挖掘机工作臂高强度钢板的矫直理论与试验研究[J]. 机械工程学报, 2017, 53(8): 82-90.
[7]	马自勇, 马立峰, 王荣军, 黄庆学, 马立东. 棒材高精度二辊矫直质量控制策略研究[J]. 机械工程学报, 2017, 53(20): 77-88.
[8]	张凯, 宋锦春, 李松, 时佳. 基于分类学习粒子群优化算法的液压矫直机控制[J]. 机械工程学报, 2017, 53(18): 202-208.
[9]	于高潮, 赵军, 邢娇娇, 赵非平, 李森林. 对称式三辊矫圆工艺研究[J]. 机械工程学报, 2017, 53(14): 136-143.
[10]	于高潮, 赵军, 马瑞, 翟瑞雪. 往复弯曲统一曲率定理及其试验验证^*[J]. 机械工程学报, 2016, 52(18): 57-63.
[11]	何安瑞, 刘东冶, 刘超. 塑性强化材料辊式矫直力学行为研究^*[J]. 机械工程学报, 2016, 52(18): 85-91.
[12]	刘东冶, 何安瑞, 王海滨, 贺龙军. 塑性强化材料矫直反弯特性研究[J]. 机械工程学报, 2015, 51(8): 76-83.
[13]	张清东, 周岁, 张晓峰, 张勃洋. 薄带钢拉矫机浪形矫平过程机理建模及有限元验证[J]. 机械工程学报, 2015, 51(2): 49-57.
[14]	张子骞, 颜云辉, 杨会林. 基于Bazier效应的薄壁管材连续矫直截面变形研究[J]. 机械工程学报, 2015, 51(10): 62-68.
[15]	赵军;宋晓抗;曹宏强;刘娟. 大型直缝焊管多点弯曲一次性矫直新工艺原理[J]. , 2014, 50(2): 92-97.