行星滚柱丝杠副螺旋曲面啮合机理研究

doi:10.3901/JME.2016.03.026

机械工程学报 ›› 2016, Vol. 52 ›› Issue (3): 26-33.doi: 10.3901/JME.2016.03.026

扫码分享

行星滚柱丝杠副螺旋曲面啮合机理研究

付晓军, 刘更, 马尚君, 佟瑞庭

西北工业大学陕西省机电传动与控制工程实验室西安 710072

收稿日期:2015-02-06 修回日期:2015-11-10 出版日期:2016-02-05 发布日期:2016-02-05
通讯作者: 刘更，男，1961年出生，博士，教授，博士研究生导师。主要研究方向为机械系统动力学、机械传动、接触力学和机电作动系统。 E-mail：npuliug@nwpu.edu.cn
作者简介:付晓军，男，1987年出生，博士研究生。主要研究方向为行星滚柱丝杠副传动。 E-mail: fuxiaojun1987@126.com
基金资助:
国家自然科学基金(51275423, 51505381)、教育部高等学校博士学科点专项科研基金(20126102110019)、高等学校学科创新引智计划(B13044)和中国博士后科学基金 (2014M552483)资助项目

Studies on Meshing Mechanism of Helical Surfaces in Planetary Roller Screw Mechanism

FU Xiaojun, LIU Geng, MA Shangjun, TONG Ruiting

Shaanxi Engineering Laboratory for Transmissions and Controls, Northwestern Polytechnical University, Xi’an 710072

Received:2015-02-06 Revised:2015-11-10 Online:2016-02-05 Published:2016-02-05

摘要/Abstract

摘要： 行星滚柱丝杠副是一种通过多个滚柱与丝杠及螺母之间螺旋曲面啮合传递动力与运动的传动机构。基于多头螺纹结构特点，建立了丝杠、滚柱和螺母螺纹的曲面方程。利用啮合曲面的连续相切接触条件，通过引入丝杠、滚柱或螺母螺旋曲面沿轴线移动的矢量，提出一种行星滚柱丝杠副啮合点位置与轴向侧隙的计算方法。在此基础上，推导得出丝杠和滚柱与螺母和滚柱之间的啮合方程以及轴向侧隙公式，将该啮合方程与现有计算方法进行比较验证其正确性，并进一步分析了当丝杠、滚柱和螺母牙型角相同时行星滚柱丝杠副的啮合点位置、轴向侧隙以及啮合螺旋曲面之间的轴向间隙分布。结果表明：丝杠和滚柱的啮合点会偏向二者螺纹牙顶；螺母和滚柱的啮合点位于螺纹中径切点处；为实现无侧隙设计，丝杠、滚柱和螺母应具有不同牙厚。

关键词: 螺旋曲面, 啮合机理, 行星滚柱丝杠副, 轴向侧隙

Abstract: Planetary roller screw mechanism (PRSM) transfers power and movement by the meshing of helical surfaces of a few rollers contacting with the screw and nut. The helical surface equations of roller, screw and nut thread surfaces are established based on the multi-start thread structural characteristics. According to the continuous tangency conditions of meshing surfaces, a method to calculate the meshing point positions and axial clearances of the PRSM is presented by utilizing the vectors described the translation of the screw, roller and nut thread surfaces along their axis. Then, the meshing equations and the axial clearances at the screw/roller and nut/roller interfaces are derived. By comparing the results obtained by existed calculation method with those by the presented meshing equations, the feasibility of meshing equations is validated. The meshing point positions, axial clearances of PRSM and axial gap distributions of two meshing surfaces are analyzed in the case that the screw, roller and nut’s flank angles are identical. The results show that the meshing point at screw/roller interface will incline to the top of the screw and roller’s thread; the meshing point at nut/roller interface will lie on the tangent point of pitch circles of the two meshing components; in order to eliminate the axial clearance during the design, the thread thickness of the screw, roller and nut should be different.

Key words: axial clearance, helical surface, meshing mechanism, planetary roller screw mechanism

中图分类号:

TH132

付晓军, 刘更, 马尚君, 佟瑞庭. 行星滚柱丝杠副螺旋曲面啮合机理研究[J]. 机械工程学报, 2016, 52(3): 26-33.

FU Xiaojun, LIU Geng, MA Shangjun, TONG Ruiting. Studies on Meshing Mechanism of Helical Surfaces in Planetary Roller Screw Mechanism[J]. Journal of Mechanical Engineering, 2016, 52(3): 26-33.

参考文献

[1] LEMOR P C．The roller screw：An efficient and reliable mechanical component of electro-mechanical actuators [C]//Energy Conversion Engineering Conference，Aug．11-16，1996，Washington DC：IEEE，1996：215-220．
[2] LOHMEIER S，BUSCHMANN T，ULBRICH H．Humanoid robot LOLA [C]//2009 IEEE International Conference on robotics and automation，May．12-17，2009，Kobe，Japan：IEEE，2009：775-780．
[3] GARCIA A，CUSIDO J，ROSERO J A，et al．Reliable electro-mechanical actuators in aircraft [J]．Aerospace and Electronic Systems Magazine，IEEE，2008，23(8)：19-25．
[4] HOJJAT Y，AGHELI M M．A comprehensive study on capabilities and limitations of roller-screw with emphasis on slip tendency [J]．Mechanism and Machine Theory，2009，44(10)：1887-1899．
[5] VELINSKY S A，CHU B，LASKY T A．Kinematics and efficiency analysis of the planetary roller screw mechanism [J]．Journal of Mechanical Design，2009，131(1)：011016-1-011016-8．
[6] JONES M H，VELINSKY S A．Kinematics of roller migration in the planetary roller screw mechanism[J]．Journal of Mechanical Design，2012，134(6)：061006-1 -061006-8．
[7] JONES M H, VELINSKY S A．Stiffness of the roller screw mechanism by the direct method[J]．Mechanics Based Design of Structures and Machines，2014，42(1)：17-34．
[8] FALKNER M，NITSCHKO T，SUPPER L，et al．Roller screw lifetime under oscillatory motion: from dry to liquid lubrication [C]//The Proceedings of the 10th European Space Mechanisms and Tribology Symposium，Sep．24-26，2003，San Sebastian，Spain，2003：297-301．
[9] 马尚君，刘更，佟瑞庭．行星滚柱丝杠副摩擦力矩及传动效率研究[J]．哈尔滨工业大学学报，2013，45(11)：74-79． MA Shangjun，LIU Geng，TONG Ruiting．Study on the frictional moment and transmission efficiency of planetary roller screw[J]．Journal of Harbin Institute of Technology，2013，45(11)：74-79．
[10] MA S J，LIU G，TONG R T，et al．A new study on the parameter relationships of planetary roller screws[J]．Mathematical Problem in Engineering，2012，doi：10.1155/ 2012 /340437．
[11] 杨家军，韦振兴，朱继生．行星滚柱丝杠副载荷分布及刚度计算[J]．华中科技大学学报，2011，39(4)：1-4． YANG Jiajun，WEI Zhenxing，ZHU Jisheng．Calculation of the load distribution of a planetary roller screw for static rigidity[J]．Journal of Huazhong University of Science and Technology，2011，39(4)：1-4．
[12] JONES M H，VELINSKY S A．Contact kinematics in the roller screw mechanism[J]．Journal of Mechanical Design，2013，135：051003-1-051003-10．
[13] 梅向明，黄敬之．微分几何[M]．北京：高等教育出版社，2008． MEI Xiangming，HUANG Jingzhi．Differential geometry [M]. Beijing：Higher Education Press，2008．
[14] LITVIN F L. Gear geometry and applied theory [M]. New Jersey：PTR Prentice Hall，1994．

行星滚柱丝杠副螺旋曲面啮合机理研究

Studies on Meshing Mechanism of Helical Surfaces in Planetary Roller Screw Mechanism

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics

本文评价

[1]	付晓军, 刘更, 马尚君, 佟瑞庭. 考虑零件偏斜的行星滚柱丝杠副啮合特性研究^*[J]. 机械工程学报, 2017, 53(3): 25-33.
[2]	李国龙;孙孟辉;李先广;刘飞. 螺旋面截形尖点矢量离散法及其在双圆弧滚刀过渡曲面最小化中的应用[J]. , 2011, 47(17): 187-192.