无油润滑空压机填料密封环的摩擦特性

›› 2009, Vol. 45 ›› Issue (7): 114-119.

无油润滑空压机填料密封环的摩擦特性

杨学宾;晋欣桥;杜志敏;崔天生;杨绍侃

上海交通大学机械与动力工程学院;嘉兴学院建筑环境与设备工程系;西安交通大学能源与动力工程学院

发布日期:2009-07-15

Tribological Characteristic of Packing Rings for Oil-free Lubricated Gas Compressors

YANG Xuebin;JIN Xinqiao;DU Zhimin;CUI Tiansheng;YANG Shaokan

School of Mechanical Engineering, Shanghai Jiao Tong University Department of Building Environment and Facility Engineering, Jiaxing University School of Energy and Power Engineering, Xi’an Jiaotong University

Published:2009-07-15

摘要/Abstract

摘要： 在往复式无油润滑压缩机装置上，试验研究了普通填充聚四氟乙烯(PTFE)、30%碳纤维增强PTFE和C/C+PTFE三种不同材料填料密封环的摩擦力、摩擦功率和摩擦温度。结果表明，普通填充PTFE材料的摩擦力受活塞平均滑行速度的影响最大，其摩擦功率和摩擦温度也最大。虽然C/C+PTFE的摩擦功率略高于30%碳纤维增强PTFE，但其摩擦温度比30%碳纤维增强PTFE低。由于C/C+PTFE具有非常良好的力学性能和较好摩擦特性，它有望成为高压、高速工作条件下的密封环材料。

关键词: PTFE复合材料, 摩擦特性, 填料密封环, 无油润滑

Abstract: Triobological experiments are performed in a reciprocating oil-free compressor arrangement to investigate the friction force, power consumption and friction temperature of three materials of pressure packing seals. These rings are respectively made in common filled polytetrafluroethylene (Filled PTFE), PTFE filled with 30% carbon fiber (30% CF + PTFE), and carbon-carbon composites with PTFE infiltrated (C/C+PTFE). Tests are performed at mean piston speed of 0.4, 0.8, 1.2, 1.6, 2.0 m/s and under a sealing pressure of 0.5, 1.0, 1.5, 2.0 MPa. The influence of mean sliding velocity on friction force of filled PTFE rings is greater than on that of the two other rings. And the power consumption and friction temperature of filled PTFE rings is the highest among the three materials. C/C+PTFE presents the lowest friction temperature, although its power consumption is slightly greater than 30% CF + PTFE. Owing to its good mechanical performances and tribological behaviors, C/C+PTFE is an optimum and promising material under conditions with sealing pressure up to 10 MPa and sliding velocity of more than 4.0 m/s.

Key words: Oil-free lubrication, Packing rings, PTFE composites, Tribological characteristic

中图分类号:

TH45

杨学宾;晋欣桥;杜志敏;崔天生;杨绍侃. 无油润滑空压机填料密封环的摩擦特性[J]. , 2009, 45(7): 114-119.

YANG Xuebin;JIN Xinqiao;DU Zhimin;CUI Tiansheng;YANG Shaokan. Tribological Characteristic of Packing Rings for Oil-free Lubricated Gas Compressors[J]. , 2009, 45(7): 114-119.

[1]	李直, 陈剑, 沈锦龙, 刘焜. 基于双盘试验的齿面时变摩擦特性研究[J]. 机械工程学报, 2018, 54(3): 73-81.
[2]	徐万里, 赵巍, 徐曦萌, 粟斌. 手动变速箱油摩擦特性评定试验台研制[J]. 机械工程学报, 2016, 52(23): 176-181.
[3]	张立军;余佳;刁坤;孟德建;余卓平. 基于盘-销系统的摩擦尖叫条件下的动态时滞摩擦特性分析[J]. , 2013, 49(5): 69-74.
[4]	胡旭晓. 机床进给系统摩擦特性分析及改善措施研究[J]. , 2005, 41(8): 185-189.
[5]	黄敏纯;高诚辉;黄录官. 模具粗糙度对板材拉延件摩擦特性的影响[J]. , 2004, 40(2): 177-180.