• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (17): 463-472.doi: 10.3901/JME.260919

• 制造工艺与装备 • 上一篇    

扫码分享

皮秒激光背面反射聚焦螺旋层切微通孔锥角探究

李锐, 王后孝   

  1. 山东理工大学山东省高性能精密制造与复合加工重点实验室 淄博 255000
  • 收稿日期:2025-09-14 修回日期:2025-12-29 发布日期:2026-11-20
  • 作者简介:李锐,男,1998年出生。主要研究方向为激光制孔。E-mail:lirui12012022@163.com;王后孝(通信作者),男,1977年出生,博士,副教授。主要研究方向为激光制孔和激光复合加工。E-mail:wanghx@sdut.edu.cn
  • 基金资助:
    山东省自然科学基金资助项目(ZR2022ME080)。

Study on Taper Angles for Through Holes Machined by Using Picosecond Laser Spiral Layer Micro Cutting Combined with Backside Reflection and Refocusing

LI Rui, WANG Houxiao   

  1. Shandong Provincial Key Laboratory of High Performance Precision Manufacturing and Hybrid Machining, Shandong University of Technology, Zibo 255000
  • Received:2025-09-14 Revised:2025-12-29 Published:2026-11-20

摘要: 针对超快激光制孔过程中存在的孔深小和锥形孔的难题,提出并采用皮秒激光背面反射聚焦螺旋层切新方法解决。在分析皮秒激光焦点的逐层离焦量和旋切层进量对成孔孔深和孔径的影响规律的基础之上,探究了背面反射聚焦螺旋层切对孔出口扩径、锥角消减、切孔效率以及孔壁改善的影响效果与机理。研究发现,当激光焦斑逐层离焦量为零时,皮秒激光螺旋层切孔深最大。与单层旋切相比,采用多层旋切,孔深显著增大。采用背面反射聚焦螺旋层切新方法,通孔出口扩径明显,通孔锥角消减显著,切孔效率有效提升,通孔出口孔壁形貌明显改善,通过增大旋切层进量,锥角进一步有效消减。

关键词: 皮秒激光, 螺旋层切, 背面反射聚焦, 微孔, 锥角

Abstract: A novel method, which is called the picosecond laser spiral layer micro cutting combined with backside reflection and refocusing, is proposed and utilized to solve the problems in terms of small hole depth and tapered hole, which usually occur during the process of ultrafast laser hole machining. The effect of the backside picosecond laser spiral layer cutting using a reflected and refocused laser beam on the hole exit enlargement, the taper angle reduction, the hole cutting efficiency and the hole wall improvement is accordingly explored with mechanism analysis based on the analysis for the influence of the transient cutting layer defocus distance and the axial layer feed distance of the picosecond laser focal spot on the machined hole depth and diameter. It is found that the peak hole depth is machined by using picosecond laser spiral layer cutting when the defocus distance of the laser focal spot is defined as zero referencing to each transient cutting layer. As compared to the single-layer picosecond laser spiral cutting, the hole depth is notably increased by using the multi-layer picosecond laser spiral cutting. Furthermore, the through-hole exit is notably enlarged together with an effective improvement for the hole cutting efficiency while the through-hole taper angle is greatly reduced by using this newly proposed method. In addition, when applying the method proposed, the hole wall morphology near the through-hole exit is improved notably, and the hole taper angle is further reduced effectively by increasing the feed distance for laser spiral layer cutting.

Key words: picosecond laser, spiral layer micro cutting, backside reflection and refocusing, micro hole, taper angle

中图分类号: