• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (17): 387-398.doi: 10.3901/JME.260917

• 数字化设计与制造 • 上一篇    

扫码分享

热塑性复合材料自动铺放成型中线聚焦红外加热技术研究

梁建国1,2,3, 李辉1,2, 刘丰玮1,2, 张硕1,2, 刘江林1,2, 武婷2   

  1. 1. 太原理工大学机械工程学院 太原 030024;
    2. 太原理工大学先进金属复合材料成形技术与装备教育部工程研究中心 太原 030024;
    3. 新疆智能装备研究院 阿克苏 843000
  • 收稿日期:2025-09-10 修回日期:2026-03-01 发布日期:2026-11-20
  • 作者简介:梁建国(通信作者),男,1975年出生,博士,教授,博士研究生导师。主要研究方向为碳纤维复合材料成型工艺及装备开发。E-mail:liangjianguo20@tyut.edu.cn
  • 基金资助:
    国家科技重大专项资助项目(2024ZD0701601)。

Study on Line-focused Infrared Heating Technology in Automatic Fiber Placement Processing of Thermoplastic Composites

LIANG Jianguo1,2,3, LI Hui1,2, LIU Fengwei1,2, ZHANG Shuo1,2, LIU Jianglin1,2, WU Ting2   

  1. 1. College of Mechanical Engineering, Taiyuan University of Technology, Taiyuan 030024;
    2. Engineering Research Center of Advanced Metal Composites Forming Technology and Equipment of Ministry of Education, Taiyuan University of Technology, Taiyuan 030024;
    3. Xinjiang Intelligent Equipment Research Institute, Aksu 843000
  • Received:2025-09-10 Revised:2026-03-01 Published:2026-11-20

摘要: 传统的红外加热器由于能量密度低,往往不能满足热塑性复合材料自动铺放的特殊要求,因此提出了一种高能量密度、快速响应的线聚焦红外加热技术,并深入研究了工艺参数对热塑性复合材料自动铺放温度场的影响。首先,解析了线聚焦红外加热及传热理论,建立加热功率、铺放速率与加热温度的匹配关系,为温度控制提供理论基础;其次,利用传热学原理,建立三维有限元模型,预测了铺放过程中温度场分布的演变机制;最后,基于自主开发的线聚焦红外加热自动铺放设备,搭建了温度场在线测量平台,实验验证了线聚焦红外加热器的可行性及有限元模型的可靠性。研究结果表明:在加热功率为770 W、模具温度为25 ℃、铺放速度为30 mm/s的工艺参数下可实现CF/PPS预浸料的较高质量铺放,验证了所提出新装备的可行性;同时,仿真结果与实验数据一致性良好,各层的温度峰值误差不超6%,为后续热塑性复合材料自动铺放工艺参数的选择及优化提供了可靠的依据。

关键词: 热塑性复合材料, 自动铺放, 原位固结, 红外加热, 温度场

Abstract: A high-energy-density, rapid-response line-focused infrared heating technology is developed to overcome the limitations of conventional infrared heaters, which exhibit low energy density and are insufficient for the specific requirements of automated thermoplastic composite layup. The effects of process parameters on the temperature field during the automated layup of thermoplastic composites are systematically investigated. The thermal and radioactive transfer theories underlying line-focused infrared heating are analyzed, and a matching relationship among heating power, layup speed, and temperature is established to enable precise temperature control. A three-dimensional finite element model based on heat transfer principles is constructed to predict the evolution of the temperature distribution during the process. An in-situ temperature measurement platform is built on a custom-designed automated layup device employing line-focused infrared heating to experimentally verify the feasibility of the heating method and the accuracy of the finite element model. The results demonstrate that under the process parameters of a heating power of 770 W, a mold temperature of 25℃, and a placement speed of 30 mm/s, high-quality placement of CF/PPS prepreg can be achieved, confirming the feasibility of the proposed new equipment. Furthermore, the simulation results show good consistency with the experimental data, with a maximum temperature peak error of no more than 6% across layers, providing a reliable basis for the selection and optimization of process parameters in future automatic placement of thermoplastic composites.

Key words: thermoplastic composites, automated fiber placement, in-situ consolidation, infrared heating, temperature field

中图分类号: