• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (17): 482-492.doi: 10.3901/JME.260394

• 制造工艺与装备 • 上一篇    

扫码分享

基于Preston方程和NSGA-Ⅱ算法的单磨头瓷砖抛磨轨迹生成方法

韩文1, 杨振恒1, 褚福磊2, 隋旭东3, 于盛睿1, 徐磊1   

  1. 1. 景德镇陶瓷大学机械电子工程学院 景德镇 333403;
    2. 清华大学机械工程学院 北京 100084;
    3. 科达制造股份有限公司 佛山 528313
  • 收稿日期:2025-09-20 修回日期:2026-02-25 发布日期:2026-11-20
  • 作者简介:韩文,男,1969年出生,博士,教授,博士研究生导师。主要研究方向为陶瓷机械设计、智能制造及应用。Email:hanwen@jcu.edu.cn
  • 基金资助:
    国家自然科学基金(52065029)、江西省自然科学基金重点(20212ACB204013)和景德镇市陶瓷产业重大产学研协同攻关和成果转化(2023ZDGC003)资助项目。

Optimization of Single Grinding Head Tile Polishing Trajectory Based on Preston's Equation and NSGA-II Algorithm

HAN Wen1, YANG Zhenheng1, CHU Fulei2, SUI Xudong3, YU Shengrui1, XU Lei1   

  1. 1. School of Mechanical and Electronic Engineering, Jingdezhen Ceramic University, Jingdezhen 333403;
    2. School of Mechanical and Electronic Engineering, Tsinghua University, Beijing 100084;
    3. Keda Industrial Group Co., Ltd, Foshan 528313
  • Received:2025-09-20 Revised:2026-02-25 Published:2026-11-20

摘要: 针对瓷砖抛磨连续化生产中出现的过抛、漏抛问题,提出一种基于Preston方程和非支配排序的遗传(NSGA-Ⅱ)算法的单磨头抛磨轨迹生成方法,可根据设定的产量大小,自动生成适合瓷砖尺寸、抛磨均匀性好的加工轨迹。利用抛磨轨迹外轮廓方程,构建以轨迹最小重叠面积和漏抛程度的多目标优化模型;通过Preston方程构建抛磨模型,计算出衡量抛磨轨迹整体均匀性的评价函数。采用带精英策略的NSGA-Ⅱ算法对优化模型进行求解,使用评价函数对Pareto最优解集计算筛选,导出整体抛磨均匀性最优的加工参数。仿真和试验结果表明,在相同产量下优化后轨迹的抛磨变异系数由初始的0.517 4显著降低至0.297 4,光泽度分布范围由原始的0~73.8 GU缩小至47.4~74.7 GU,平均光泽度值提升了14.88%(计算基数:55.3 GU),避免了抛磨过程中的漏抛现象,过抛情况得到进一步改善,可有效提升传统建筑陶瓷瓷砖抛磨效率和加工均匀性。

关键词: 瓷砖抛磨, 轨迹生成, Preston方程, NSGA-Ⅱ算法, 抛磨均匀性

Abstract: To address the problems of overthrow and leakage in the continuous production of tile grinding, a single-head grinding trajectory generation method based on Preston’s equation and NSGA-II algorithm is proposed, which can automatically generate a processing trajectory suitable for the size of tiles and good uniformity of grinding according to the set output size. The multi-objective optimization model with the minimum overlap area of the trajectory and the degree of leakage is constructed by using the outer contour equation of the grinding trajectory; the grinding model is constructed by Preston's equation, and the evaluation function to measure the overall uniformity of the grinding trajectory is calculated. The optimization model is solved using NSGA-II with an elite strategy, and the Pareto optimal solution set is computationally screened using an evaluation function to derive the processing parameters that are optimal for the overall uniformity of grinding. Simulation and experimental results demonstrate that, under the same production output, the coefficient of variation for polishing uniformity is significantly reduced from the initial value of 0.5174 to 0.2974 after trajectory optimization. The glossiness distribution range was narrowed from the original 0–73.8 GU to 47.4–74.7 GU, while the average glossiness value increased by 14.88% (baseline: 55.3 GU). The optimized trajectory effectively eliminated unpolished areas and further mitigated over-polishing, thereby enhancing both the efficiency and uniformity of the polishing process for conventional architectural ceramic tiles.

Key words: tile polishing, trajectory generation, Preston equation, NSGA-II algorithm, grinding uniformity

中图分类号: