随焊感应加热尺寸和热源数对焊接失稳变形的影响

doi:10.3901/JME.2025.06.112

机械工程学报 ›› 2025, Vol. 61 ›› Issue (6): 112-120.doi: 10.3901/JME.2025.06.112

• 材料科学与工程 • 上一篇

扫码分享

随焊感应加热尺寸和热源数对焊接失稳变形的影响

付玲¹, 易斌^1,2, 尹莉¹, 薛丁琪¹, 任会礼¹, 王江超²

1. 起重机械关键技术全国重点实验室长沙 410013;
2. 华中科技大学船舶与海洋工程学院武汉 430074

收稿日期:2024-08-12 修回日期:2024-12-18 发布日期:2025-04-14
作者简介:付玲，女，1967年出生，博士，高级工程师，博士研究生导师。主要研究方向为大型复杂结构设计与制造。E-mail:ful@zoomlion.com;王江超(通信作者)，男，1983年出生，博士，副教授，博士研究生导师。主要研究方向为船舶海洋结构物建造工艺力学及力学性能评估。E-mail:WJccn@hust.edu.cn<
基金资助:
国家自然科学基金(52071151)和长沙市科技领军人才(kh2201012)资助项目。

Effect of Size and Number of Induction Heating during Welding Process on Buckling Distortion Induced by Welding

FU Ling¹, YI Bin^1,2, YIN Li¹, XUE Dingqi¹, REN Huili¹, WANG Jiangchao²

1. National Key Laboratory of Hoisting Machinery Key Technology, Changsha 410013;
2. School of Naval Architecture and Ocean Engineering, Huazhong University of Science and Technology, Wuhan 430074

Received:2024-08-12 Revised:2024-12-18 Published:2025-04-14

摘要/Abstract

摘要： 针对薄板焊接失稳变形难以在焊后完全矫正的问题，提出采用随焊感应加热工艺对其控制，并研究工艺参数的影响。首先，进行薄板对接接头常规焊接和随焊感应加热工艺试验；通过K型热电偶测量附加感应加热区域瞬时温度，冷却后采用三坐标仪获取接头变形轮廓。对接接头均呈现出马鞍形，但随焊感应加热工艺下焊接变形小于常规焊接的结果。随后，建立对接接头实体单元模型，考虑材料非线性和几何非线性进行热-弹-塑性有限元分析。常规焊接和随焊感应加热工艺下，计算的温度场数据和焊接变形均与试验测量结果基本吻合，验证了热-弹-塑性有限元分析的准确性。最后，通过有限元计算，研究了随焊感应加热区域尺寸和个数对焊接失稳变形控制效果的影响。结果表明，增加随焊感应加热区域尺寸和个数，能获得更好的焊接失稳变形控制效果，优化后的工艺参数可将面外变形减小90%以上。随焊感应加热形成的热拉伸作用显著降低母材区域的残余压应力，提高了焊接结构的稳定性，以此控制甚至消除焊接失稳变形。

关键词: 焊接失稳变形, 感应加热, 工艺参数, 有限元分析, 残余应力

Abstract: In order to solve the problem that buckling distortion induced by welding of thin plates structures was difficult to be perfectly corrected after welding, induction heating during welding process was proposed to control it and the effect of processing parameters was investigated. Conventional welding (CW) and induction heating during welding process were performed on butt welded joints with thin plates. The temperature histories in the additional induction heating region were measured by K-type thermocouple, while the deformation profile was obtained by a coordinate measuring machine after cooling down. The butt welded joints showed saddle shape, but the distortion under induction heating during welding process was less than that of CW. Then, a solid elements model of butt welded joint was established, which was used to conduct thermal elastic plastic (TEP) FE analysis considering material nonlinearity and geometric nonlinearity. The computed temperature histories and welding distortions were in good agreement with the measured results of CW and induction heating during welding process, so that the accuracy of TEP FE analysis was validated. Finally, the influence of the size and number for additional induction heating region on control effect of buckling distortion induced by welding was studied with the validated TEP FE analysis. The results showed that better control effect can be obtained by increasing the size and number of additional induction heating region. The optimized process parameters of induction heating during welding process can reduced out-of-plane displacement by more than 90%. The thermal stretching action formed by induction heating during welding process significantly decreased residual compressive stress in base material region and improved the stability of welded structures, so as to control or even eliminate buckling distortion induced by welding.

Key words: buckling distortion induced by welding, induction heating, processing parameters, FE analysis, residual stresses

中图分类号:

U671.83

付玲, 易斌, 尹莉, 薛丁琪, 任会礼, 王江超. 随焊感应加热尺寸和热源数对焊接失稳变形的影响[J]. 机械工程学报, 2025, 61(6): 112-120.

FU Ling, YI Bin, YIN Li, XUE Dingqi, REN Huili, WANG Jiangchao. Effect of Size and Number of Induction Heating during Welding Process on Buckling Distortion Induced by Welding[J]. Journal of Mechanical Engineering, 2025, 61(6): 112-120.

参考文献

[1] 梁伟，郑颖，邓德安. 外拘束对铝合金薄板结构焊接变形的影响[J]. 机械工程学报，2021，57(6)：70-77. LIANG Wei，ZHENG Ying，DENG Dean. Influence of external restraint on welding distortion of aluminum alloy thin-plate structures[J]. Journal of Mechanical Engineering，2021，57(6)：70-77.
[2] 樊丁，韩苗苗，赵金龙，等. 随焊氩气激冷控制铝/钢薄板焊接应力与变形数值模拟[J]. 兰州理工大学学报，2020，46(4)：22-26. FAN Ding，HAN Miaomiao，ZHAO Jinlong，et al. Numerical simulation of stress and deformation for Al/steel sheet welding by trailing cooling of argon gas[J]. Journal of Lanzhou University of Technology，2020，46(4)：22-26.
[3] ZHOU H，YI B，SHEN C，et al. Mitigation of welding induced buckling with transient thermal tension and its application for accurate fabrication of offshore cabin structure[J]. Marine Structures，2022，81：103104.
[4] 易斌，周方明，王江超. 瞬态热拉伸强度对304L不锈钢焊接变形影响的计算分析[J]. 机械工程学报，2021，57(6)：60-69. YI Bin，ZHOU Fangming，WANG Jiangchao. Computation and analysis of the influence of transient thermal tensioning intensity on welding distortion in butt joint with 304L stainless steel[J]. Journal of Mechanical Engineering，2021，57(6)：60-69.
[5] WATANABE M，SATOH K. On the type of distortion in various welded joints: shrinkage distortion in welded joint (Report 5)[J]. Quarterly Journal of the Japan Welding Society，1957，26(6)：399-405.
[6] TERASAKI T，MAEDA K，MURAKAWA H，et al. Critical conditions of plate buckling generated by welding[J]. Transaction of the Japan Society of Mechanical Engineering Series A，1998，64(625)：2239-2244.
[7] TSAI C，HAN M，JUNG G. Investigating the bifurcation phenomenon in plate welding[J]. Welding Journal，2006，85(7)：151-162.
[8] ZAEEM M，NAMI M，KADIVAR M. Prediction of welding buckling distortion in a thin wall aluminum T joint[J]. Computational Materials Science，2007，38(4)：588-594.
[9] DENG D，ZHOU Y，BI T，et al. Experimental and numerical investigations of welding distortion induced by CO₂ gas arc welding in thin-plate bead-on joints[J]. Materials & Design，2013，52：720-729.
[10] WANG J，ZHOU X，YI B. Buckling distortion investigation during thin plates butt welding with considering clamping influence[J]. CIRP Journal of Manufacturing Science and Technology，2022，37：278-290.
[11] GUAN Q，GUO D，LI C，et al. Low stress non-distortion (LSND) welding-a new technique for thin materials[J]. Welding in the World，1994，33(3)：160-167.
[12] DEO M，MICHALERIS P. Mitigation of welding induced buckling distortion using transient thermal tensioning[J]. Science and Technology of Welding and Joining，2003，8(1)：49-54.
[13] SOUTO J，ARES E，ALEGRE P，et al. Methodology to reduce distortion using a hybrid thermal welding process[J]. Materials，2018，11(9)：1649.
[14] YI B，WANG J. Mechanism clarification of mitigating welding induced buckling by transient thermal tensioning based on inherent strain theory[J]. Journal of Manufacturing Processes，2021，68：1280-1294.
[15] 张水明. 船用钢板移动电磁加热成形规律及感应器优化研究[D]. 上海：上海交通大学，2019. ZHANG Shuiming. Research on thermal forming for ship hull plate fabricated by moving electromagnetic heating method and structure and parameter optimization of inductor[D]. Shanghai：Shanghai Jiao Tong University，2019.
[16] Rudnev V，Cook R L，Loveless D. Handbook of Induction Heating[M]. Boca Raton：CRC Press，2017.
[17] 孙建志，冯敏超，陈小雨. 大型邮轮薄板建造变形控制方法[J]. 船海工程，2022，51(1)：1-6. SUN Jianzhi，FENG Minchao，CHEN Xiaoyu. Deformation control method of sheet construction for large liner[J]. Ship and Ocean Engineering，2022，51(1)：1-6.
[18] Zhang X，Chen C，Liu Y. Numerical analysis and experimental research of triangle induction heating of the rolled plate[J]. Proceedings of the Institution of Mechanical Engineers，Part C：Journal of Mechanical Engineering Science，2017，231(5)：844-859.
[19] Wang J，Yi B，Zhang C，et al. Experiments of double curvature plate bending with induction heating and processing parameters investigation by computational analysis[J]. Ocean Engineering，2019，192：106596.
[20] WANG J，YI B. Benchmark investigation of welding-induced buckling and its critical condition during thin plate butt welding[J]. Journal of Manufacturing Science and Engineering，2019，141(7)：071010.
[21] LI Z，FENG G，DENG D，et al. Investigating welding distortion of thin-plate stiffened panel steel structures by means of thermal elastic plastic finite element method[J]. Journal of Materials Engineering and Performance，2021，30(5)：3677-3690.

随焊感应加热尺寸和热源数对焊接失稳变形的影响

Effect of Size and Number of Induction Heating during Welding Process on Buckling Distortion Induced by Welding

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	廖朋朋, 周帼彦, 张玉财, 张显程, 蒋文春, 涂善东. 基于钎料适配性的航空发动机回热器寿命提升方法研究[J]. 机械工程学报, 2025, 61(6): 103-111.
[2]	汪汉明, 董庆兵, 陈壮, 赵波, 史修江. 行星轮系竞争失效的寿命预测及试验研究[J]. 机械工程学报, 2025, 61(3): 284-298.
[3]	王蔚, 李晓旭, 刘伟军, 卞宏友, 邢飞, 王静. 激光清洗7075铝合金清洗质量建模及多目标优化研究[J]. 机械工程学报, 2025, 61(3): 422-439.
[4]	刘瑞伟, 张碧峰, 范雅婷, 温兆麟, 肖体兵, 郭宏伟. 索-梁-膜张拉式天线展开机构非线性动力学特性及参数优化分析[J]. 机械工程学报, 2025, 61(1): 92-100.
[5]	陈钊杰, 谢晋, 刘军汉, 熊长新, 李迪帆. 脉冲放电驱动磨料流辅助磨削单晶碳化硅研究[J]. 机械工程学报, 2024, 60(9): 383-392.
[6]	赵希坤, 李聪波, 杨勇, 吕岩, 姜书艳. 数据-机理混合驱动下考虑刀具柔性的柔性加工工艺参数能效优化方法[J]. 机械工程学报, 2024, 60(7): 236-248.
[7]	赵承伟, 张文豪, 龚天诚, 张逸云, 王长涛, 罗先刚. 平面光学元件超平整吸附装载的优化设计与分析[J]. 机械工程学报, 2024, 60(5): 241-248.
[8]	胡龙, 刘红艳, 成慧梅, 陈维奇, 冯广杰, 叶延洪, 邓德安. 超高强耐磨钢NM500多层多道对接接头残余应力的研究[J]. 机械工程学报, 2024, 60(4): 335-344.
[9]	马泳涛, 孙宁, 王俊龙, 李春凡, 卢春生, 张彬, 刘兰荣. 前混合水射流喷丸覆盖率计算及对渗碳钢表面完整性的影响研究[J]. 机械工程学报, 2024, 60(3): 393-404.
[10]	周晓丽, 杜仕忠, 王江超, 赵宏权, 吴磊. 外部拘束控制板架结构焊接失稳变形的研究[J]. 机械工程学报, 2024, 60(24): 142-152.
[11]	顾磊, 王鹏程, 闫耀天, 陈海燕, 李文亚. 负膨胀材料在复合材料制备和钎焊中的研究进展[J]. 机械工程学报, 2024, 60(22): 1-20.
[12]	李淳, 陈雷, 司晓庆, 亓钧雷, 曹健. 陶瓷-金属接头残余应力调控研究综述[J]. 机械工程学报, 2024, 60(22): 21-39.
[13]	代金垚, 刘献栋, 单颖春, 姜二. 汽车钢制车轮组合焊接的残余应力场研究[J]. 机械工程学报, 2024, 60(22): 291-301.
[14]	熊健, 张之敬, 陈骁, 萨仁其木格, 苏亮, 金鑫. 精密光学元件胶接装配性能研究进展[J]. 机械工程学报, 2024, 60(22): 364-384.
[15]	田晶, 高崇, 关焦月, 付鹏哲, 刘仕运, 姚玉东. 收口自锁螺母高保真建模方法及松动特性研究[J]. 机械工程学报, 2024, 60(21): 132-143.