310S不锈钢焊接接头高温力学性能及组织演变

doi:10.3901/JME.2024.12.250

机械工程学报 ›› 2024, Vol. 60 ›› Issue (12): 250-258.doi: 10.3901/JME.2024.12.250

扫码分享

310S不锈钢焊接接头高温力学性能及组织演变

姜云禄^1,2,3, 陈静^1,2, 阚盈^1,2, 吴昌忠², 陈怀宁^1,2

1. 中国科学院核用材料与安全评价重点实验室沈阳 110016;
2. 中国科学院金属研究所沈阳 110016;
3. 中国科学技术大学材料科学与工程学院沈阳 110016

收稿日期:2023-12-08 修回日期:2024-02-21 出版日期:2024-06-20 发布日期:2024-08-23
作者简介:姜云禄,男,1986年出生,博士研究生,助理研究员。主要研究方向为金属材料焊接及质量调控。E-mail:yljiang@imr.ac.cn;陈怀宁(通信作者),男,1962年出生,博士,研究员,硕士研究生导师。主要研究方向为焊接质量控制与可靠性连接。E-mail:hnchen@imr.ac.cn
基金资助:
中核集团领创科研资助项目。

Mechanical Properties and Microstructure Evolution of 310S Austenitic Stainless Steel Welded Joint at High Temperature

JIANG Yunlu^1,2,3, CHEN Jing^1,2, KAN Ying^1,2, WU Changzhong², CHEN Huaining^1,2

1. Key Laboratory of Nuclear Materials and Safety Assessment, Chinese Academy of Sciences, Shenyang 110016;
2. Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016;
3. School of Materials Science and Engineering, University of Science and Technology of China, Shenyang 110016

Received:2023-12-08 Revised:2024-02-21 Online:2024-06-20 Published:2024-08-23

摘要/Abstract

摘要： 耐热不锈钢是高放废液固化容器的理想材料，而焊接接头的高温性能和组织演化对固化容器的尺寸稳定性和服役安全具有重要影响。基于等离子弧焊接技术制备310S奥氏体不锈钢焊接接头，研究不同温度(室温～1 100 ℃)对焊接接头拉伸性能的影响和分别在600 ℃和1 100 ℃条件下焊接接头的蠕变性能。借助光学显微镜、扫描电镜、背散射电镜、透射电镜和拉伸试验机，对金相组织、断口形貌、相组成及元素分布和拉伸性能进行分析。结果表明：敏化温度附近材料的伸长率最低，拉伸断口出现较大空洞，随着温度升高至1 100 ℃，断口表面出现氧化。焊接接头具有优异的抗高温蠕变性能，600 ℃蠕变试验后在母材区形成孪晶组织，1 100 ℃蠕变后焊缝区铁素体消失，晶粒尺寸出现长大。高温和应力作用促进晶界处析出M₂₃C₆相，削弱晶界强度，裂纹在晶界处形核、长大和扩展，最终造成焊接接头出现沿晶断裂。研究成果为高放废液固化容器的服役安全提供参考，同时丰富了高放废液后处理的基础数据。

关键词: 310S不锈钢, 焊接接头, 高温力学性能, 组织演变, 蠕变

Abstract: Heat-resistant stainless steel is an ideal material for high level waste liquid solidified container, and the high temperature properties and microstructure evolution of welded joints have an important effect on dimensional stability and service safety for solidified container. The welding joint of 310S austenitic stainless steel is prepared by plasma arc welding technology. The influence of different temperatures (room temperature to 1 100 ℃) on the tensile properties of the welded joint and the creep properties of the welded joint at 600 ℃ and 1 100 ℃ are studied. The microstructure, fracture morphology, phase composition, element distribution and tensile properties are analyzed by means of optical microscope, scanning electron microscopy, electron back scatter diffraction, transmission electron microscopy and tensile testing machine. The results show that the elongation of the material is the lowest near the sensitization temperature, and large holes appear in the tensile fracture. With the temperature increasing to 1 100 ℃, oxidation occurs on the fracture surface. The welded joint has excellent high temperature creep resistance. Twin microstructure is formed in the base metal zone after 600 ℃ creep, ferrite disappears and grain size grows after 1 100 ℃ creep. The effects of high temperature and stress promote the precipitation of M₂₃C₆ phase at the grain boundary, which weakens the grain boundary strength. The cracks nucleate, grow and expand at the grain boundary, then finally cause the welded joints intergranular fracture. The research results provide reference for the safety of the high level waste liquid solidifying vessel and enrich the basic data of the high level waste liquid post-treatment.

Key words: 310S stainless steel, welded joint, mechanical properties, microstructure evolution, creep

中图分类号:

TG444

姜云禄, 陈静, 阚盈, 吴昌忠, 陈怀宁. 310S不锈钢焊接接头高温力学性能及组织演变[J]. 机械工程学报, 2024, 60(12): 250-258.

JIANG Yunlu, CHEN Jing, KAN Ying, WU Changzhong, CHEN Huaining. Mechanical Properties and Microstructure Evolution of 310S Austenitic Stainless Steel Welded Joint at High Temperature[J]. Journal of Mechanical Engineering, 2024, 60(12): 250-258.

参考文献

[1] 谢佼，胡喆. 国内首座高水平放射性废液玻璃固化设施投运[J]. 电子产品可靠性与环境试验，2021，39(5)：60. XIE Jiao，HU Zhe. The first glass curing facility for high-level radioactive waste liquid was put into operation in China[J]. Reliability and Environmental Testing of Electronic Products，2021，39(5)：60.
[2] LO K，SHEK C，LAI J. Recent developments in stainless steels[J]. Materials Science and Engineering R：Reports 2009，65(4)：39-104.
[3] QIAN Jiong，CHEN Changfeng，YU Haobo，et al. The influence and the mechanism of the precipitate/austenite interfacial C-enrichment on the intergranular corrosion sensitivity in 310 S stainless steel[J]. Corrosion Science，2016，111：352-361.
[4] 胡兴，彭昭成，冯广杰，等. SUS310S不锈钢局部真空电子束焊接接头残余应力及变形研究[J]. 机械工程学报，2020，56(21)：38-47. HU Xing，PENG Zhaocheng，FENG Guangjie，et al. Numerical simulation of residual stress and deformation of SUS310S stainless steel local vacuum electron beam welded joint[J]. Journal of Mechanical Engineering，2020，56(21)：38-47.
[5] JIANG Y，KAN Y，CHEN H. Heterogeneous microstructure-induced creep failure responses in various sub-zones of modified 310S welded joints[J]. Metals，2022，12(116)：1-15.
[6] KUAAMA T，OMORI T，SAITO T，et al. Ultra-large single crystals by abnormal grain growth[J]. Nature Communications，2017，8：1-9.
[7] WANG Z，LIANG T，XING W，et al. σ-phase precipitation mechanism of 15Cr–15Ni titanium-modified austenitic stainless steel during long-term thermal exposure[J]. Acta Metallurgica Sinica (English Letters)，2018，31(3)：281-289.
[8] WEST D，HULANCE J，HIGGISION R，et al. σ-phase precipitation in 347HFG stainless steel[J]. Materials Science and Technology，2013，29：835-842.
[9] GONZAGA，A C，BARBOSA C，TAVARES S，et al. Influence of post welding heat treatments on sensitization of AISI 347 stainless steel welded joints[J]. Journal of Materials Research and Technology，2020，9(1)：908-921.
[10] NASSIRAEI H，MOJTAHEDI A，LOTFOLLAHI M A，et al. Capacity of tubular X-joints reinforced with collar plates under tensile brace loading at elevated temperatures[J]. Thin Walled Structures，2019，142：426-443.
[11] NASSIREAI H，LOTFULLAHI M，NESHAEI S A，et al. Structural behavior of tubular X-joints strengthened with collar plate under axially compressive load at elevated temperatures[J]. Marine Structures，2018，61：46-61.
[12] LI R，FU B，DONG T，et al.，Effect of annealing treatment on microstructure，mechanical property and anti-corrosion behavior of X2CrNi12 ferritic stainless steel[J]. Journal of Materials Research and Technology，2022，18：448-460.
[13] FOROUZAN F，NAJAFIZADEH A，KERMANPUR A，et al.，Production of nano/submicron grained AISI 304L stainless steel through the martensite reversion process[J]. Materials Science and Engineering A，2010，527(27)：7334-7339.
[14] REZAEI H A，GHAZANI M S，EGHBALI B. Effect of post deformation annealing on the microstructure and mechanical properties of cold rolled AISI 321 austenitic stainless steel[J]. Materials Science and Engineering A，2018，736：364-374.
[15] WANG X，CHEN X M，SUN Q，et al. Formation mechanism of δ-ferrite and metallurgy reaction in molten pool during press-hardened steel laser welding[J]. Materials Letters，2017，206：143-145.
[16] 谢胜涛，邵书东，亓海燕，等. 稀土元素对430铁素体不锈钢组织和性能的影响[J]. 中国冶金，2022，32(6)：94-100. XIE Shengtao，SHAO Shudong，QI Haiyan，et al. Effect of rare earth elements on microstructure and properties of 430 ferritic stainless steel[J]. China Metallurgy，2022，32(6)：94-100.
[17] LI Hongmei，TAKATA N，KOBASHI M，et al. Effect of added stabilizing elements on thermal activation process of plastic deformation in 18Cr ferritic stainless steel[J]. Materials Science and Engineering A，2021，824：141866.
[18] TAN L，ALLEN T R，BUSBY J T. Grain boundary engineering for structure materials of nuclear reactors[J]. Journal of Nuclear Materials，2013，441(1)：661-666.
[19] HIRAYAMA K，YOSHII Y，MORIZONO Y，et al. Grain boundary engineering of 10% Cr ferritic-martensitic steel SUH3[J]. ISIJ International，2015，55(9)：1973-1979.
[20] LI Y，WANG X. Strengthening mechanisms and creep rupture behavior of advanced austenitic heat resistant steel SA-213 S31035 for A-USC power plants[J]. Materials Science and Engineering A，2020，775：138991.
[21] LU L，SHEN Y，CHEN X，et al. Ultrahigh strength and high electrical conductivity in copper[J]. Science，2004，304(5669)：422-426.
[22] 李国平，裴海祥，李建春，等. σ相对S32760超级双相不锈钢组织和性能的影响[J]. 工程科学学报，2016，38(3)：364-370. LI Guoping，PEI Haixiang，LI Jianchun，et al. Influence of σ phases on the microstructure and properties of S32760 super duplex stainless steel[J]. Chinese Journal of Engineering，2016，38(3)：364-370.
[23] CHEN X H，REN X P，XU H，et al．Effect of superplastic deformation on the bonding property of 00Cr25Ni7Mo3N duplex stainless steel[J]. Int. J. Miner. Met. Mater.，2012，19(4)：518.

310S不锈钢焊接接头高温力学性能及组织演变

Mechanical Properties and Microstructure Evolution of 310S Austenitic Stainless Steel Welded Joint at High Temperature

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	赵雷, 张利宾, 宋恺, 徐连勇, 韩永典, 郝康达. 新型马氏体耐热钢耦合控制下蠕变-疲劳循环变形研究[J]. 机械工程学报, 2024, 60(16): 118-129.
[2]	赵雷, 武言, 徐连勇, 韩永典, 熊昱. 纳入拘束效应的焊接接头蠕变裂纹扩展速率预测方法[J]. 机械工程学报, 2024, 60(14): 126-138.
[3]	李霞, 吴磊, 温泽峰, 金学松, 王安斌. 钢弹簧浮置板轨道焊接接头处钢轨波磨研究Ⅰ：初始演化[J]. 机械工程学报, 2023, 59(8): 245-252.
[4]	牛田野, 高永建, 陶贤超, 赵鹏, 宫建国, 轩福贞. 核级SA-508 Gr.3 Cl.1材料拉伸与压缩蠕变行为的比较研究[J]. 机械工程学报, 2023, 59(4): 96-104.
[5]	陈义斯, 芦刚, 严青松, 黄普英, 徐翩, 毛蒲, 周泽远. 稀土钇、铈变质真空差压铸造ZL114A合金的力学性能及蠕变机制[J]. 机械工程学报, 2023, 59(18): 186-195.
[6]	周煜, 范志超, 姜恒, 王宇轩. 改进Logistic蠕变应变预测模型及其有限元实现[J]. 机械工程学报, 2023, 59(16): 82-89.
[7]	宋明, 马帅, 杜传胜, 蒋文春, 王炳英. 不同流道布置的平板式固体氧化物燃料电池蠕变损伤研究[J]. 机械工程学报, 2023, 59(10): 76-84.
[8]	张海, 王东坡, 高志伟. 焊接残余应力对超声冲击处理焊接接头疲劳寿命的影响[J]. 机械工程学报, 2023, 59(10): 124-133.
[9]	吴海利, 张长春, 孙林根, 徐倩虹. 617镍基合金蠕变-疲劳交互力学行为与微观组织演变[J]. 机械工程学报, 2022, 58(8): 170-180.
[10]	康举, 王启冰, 王智春, 韩哲文, 左月, 张华, 焦向东. 超超临界火电机组异种钢焊接接头高温断裂机理综述[J]. 机械工程学报, 2022, 58(24): 58-83.
[11]	黄佳, 贺斟酌, 杨晓光, 石多奇, 孙燕涛. 镍基定向凝固高温合金蠕变寿命预测的改进方法[J]. 机械工程学报, 2022, 58(22): 258-268.
[12]	孙琦迪, 傅聪, 金静静, 杨蔚涛, 郝庆国, 章斌, 杨旗. VC析出相对Fe-Mn-Si-Al相变诱导塑性钢微观组织演变及力学性能的影响[J]. 机械工程学报, 2022, 58(22): 276-283.
[13]	李元, 徐连勇, 高宇, 荆洪阳, 赵雷, 韩永典. 纳米压痕研究石墨烯增强Sn-Ag-Cu钎料焊点的高温蠕变行为[J]. 机械工程学报, 2022, 58(2): 50-57.
[14]	尹立孟, 苏子龙, 左存果, 张中文, 姚宗湘, 王刚, 王善林, 陈玉华. Cu/SAC305/Cu微焊点的剪切蠕变试验及数值模拟[J]. 机械工程学报, 2022, 58(2): 300-306.
[15]	轩福贞, 朱明亮, 王国彪. 结构疲劳百年研究的回顾与展望[J]. 机械工程学报, 2021, 57(6): 26-51.