考虑尺度的结合面切向刚度模型

doi:10.3901/JME.2024.03.181

机械工程学报 ›› 2024, Vol. 60 ›› Issue (3): 181-190.doi: 10.3901/JME.2024.03.181

扫码分享

考虑尺度的结合面切向刚度模型

罗治军^1,2, 阎绍泽¹, 田桂³

1. 清华大学机械工程系北京 100084;
2. 中国人民解放军 96963 部队博士创新工作站北京 100084;
3. 陆军航空兵学院航电和兵器工程系北京 101123

收稿日期:2023-04-30 修回日期:2023-08-10 出版日期:2024-02-05 发布日期:2024-04-28
通讯作者: 阎绍泽,男,1964年出生,博士,教授,博士研究生导师。主要研究方向为机械系统动力学,智能结构设计与昆虫仿生。E-mail:yansz@mail.tsinghua.edu.cn
作者简介:罗治军,男, 1985 年出生,博士研究生。主要研究方向为机械动力学,机械故障诊断。E-mail:lzj_r@sina.com
基金资助:
国家自然科学基金(11872033)和北京市自然科学基金(3172017)资助项目。

Model of Tangential Stiffness of Joint Surface Considering Scale

LUO Zhijun^1,2, YAN Shaoze¹, TIAN Gui³

1. Department of Mechanical Engineering, Tsinghua University, Beijing 100084;
2. PhD Innovation Workstation of Unit 96963 of China People's Liberation Army, Beijing 100084;
3. Department of Avionics and Arms Engineering, Army Aviation Institute, Beijing 101123

Received:2023-04-30 Revised:2023-08-10 Online:2024-02-05 Published:2024-04-28

摘要/Abstract

摘要： 接触刚度是结合面特性中最重要的参数之一, 直接影响着机械结构整体的动力学特性。GW(Greenwood & Williamson)模型是目前被广泛应用的结合面接触模型,在许多实验中取得了较好的预测结果。理论上, GW 模型预测结果受仪器分辨率影响,预测值并不唯一,但是实验得到的宏观物理量如刚度、导电率等却是唯一值。这一矛盾说明,存在一个唯一的计算或者观测尺度以确保宏观结果的唯一性。理论上分析了 GW 模型的尺度依赖特性;研究了采用高斯滤波器实现计算尺度变换的方法;基于 Thomas 的接触理论,设计了确定滤波器截止频率的迭代方法;最终提出了一种考虑尺度的结合面切向刚度计算框架。搭建了切向刚度试验台,对考虑尺度的切向刚度模型进行验证。结果表明,考虑尺度的模型与实验结果吻合较好。

关键词: 真实接触面, 接触模型, 尺度依赖, GW 模型, MB 模型

Abstract: Contact stiffness is one of the most important parameter in the characteristics of joint surface, which directly affects the dynamic characteristics of the whole mechanical structure. GW (Greenwood & Williamson) model is a widely accepted contact model and has obtained good agreement with many experiments. Theoretically, the prediction results of GW model are affected by instrument resolution, consequently are not unique,but macroscopic physical parameters such as stiffness and conductivity are unique values. This contradiction implies that there is a single computational or observational scale to ensure the uniqueness of macroscopic results. The scale-dependent characteristics of GW model are analyzed theoretically. The method to change the computing scale by Gaussian filter is researched. Based on Thomas' contact theory, an iterative method is designed to determine the cutoff frequency of the filter, and a stiffness calculation framework for the joint surface taking scale into consideration is ultimately proposed. A tangential stiffness test-bed is built to verify the model considering scale. The results show that the model considering scale can better consist with the experimental results.

Key words: real contact area, contact model, scale dependence, GW model, MB model

中图分类号:

TH133
TH165

罗治军, 阎绍泽, 田桂. 考虑尺度的结合面切向刚度模型[J]. 机械工程学报, 2024, 60(3): 181-190.

LUO Zhijun, YAN Shaoze, TIAN Gui. Model of Tangential Stiffness of Joint Surface Considering Scale[J]. Journal of Mechanical Engineering, 2024, 60(3): 181-190.

参考文献

[1] 温淑花,张学良,陈永会.结合面切向接触等效黏性阻尼分形模型[J].西安交通大学学报, 2017, 51(1):1-8. WEN Shuhua, ZHANG Xueliang, CHEN Yonghui. Fractal model of equivalent viscous damping for tangential contact in joint interfaces[J]. Journal of Xi'an Jiaotong University, 2017, 51(1):1-8.
[2] 李辉光,刘恒,虞烈.粗糙机械结合面的接触刚度研究[J].西安交通大学学报, 2011, 45(6):69-74. LI Huiguang, LIU Heng, YU Lie. Contact stiffness of rough mechanical joint surface[J]. Journal of Xi'an Jiaotong University, 2011, 45(6):69-74.
[3] 吴阳,张学良,温淑花.机床固定结合面接触热导三维分形模型[J].太原科技大学学报, 2015, 36(5):368-374. WU Yang, ZHANG Xueliang, WEN Shuhua. Three-dimensional fractal model of contact thermal conductivity of fixed joint surfaces of machine tools[J]. Journal of Taiyuan University of Science and Technology, 2015, 36(5):368-374.
[4] 高锐,袁奇,高进.燃气轮机拉杆转子有限元模型研究及临界转速计算[J].热能动力工程, 2009, 24(3):305-308. GAO Rui, YUAN Qi, GAO Jin. Finite element model of gas turbine rod rotor and critical speed calculation[J]. Journal of Engineering for Thermal Energy and Power, 2009, 24(3):305-308.
[5] 郝燕平,朱梓根.叶片摩擦阻尼器切向刚度研究[J].航空动力学报, 2002, 17(4):426-431. HAO Yanping,ZHU Zigen. Investigation on the tangential stiffness of friction damper[J]. Journal of Aerospace Power, 2002, 17(4):426-431.
[6] 周莹,程义悦.考虑接触效应的燃气轮机拉杆转子动力学模型研究[J].装备机械, 2014, 53(3):53-57. ZHOU Ying, CHENG Yiyue. Dynamic model of gas turbine rod rotor considering contact effect[J]. The Magazine on Equipment Machinery, 2014, 53(3):53-57.
[7] 何冰冰.涡轮叶片干摩擦阻尼器动力学特性及减振特性研究[D].西安:西北工业大学, 2018. HE Bingbing. Study on dynamic characteristics and damping characteristics of turbine blade dry friction dampers[D]. Xi'an:Northwestern Polytechnical University, 2018.
[8] AKIO Y, TAKESHI K, HIROKAZU E, et al. Study on dynamic characteristics of contact joint structure[J]. Proceeding of the Japanese Mechanical Society, 1983, 49(438):182-190.
[9] 李小彭,王伟,赵米鹊.考虑摩擦因素影响的结合面切向接触阻尼分形预估模型及其仿真[J].机械工程学报, 2012, 48(23):46-50. LI Xiaopeng, WANG Wei, ZHAO Mique. Fractal prediction model for tangential contact damping of joint surface considering friction factors and its simulation[J]. Journal of Mechanical Engineering, 2012, 48(23):46-50.
[10] 王菲菲,徐颖强,刘楷安.粗糙表面切向接触刚度概率分析方法[J].浙江大学学报, 2018, 52(2):54-59. WANG Feifei, XU Yingqiang, LIU Kaian. Probability analysis method of tangential contact stiffness on rough surfaces[J]. Journal of Zhejiang University, 2018, 52(2):54-59.
[11] 王丹.基于分形理论的结合面接触刚度与摩擦力建模及分析[D].沈阳:东北大学, 2015. WANG Dan. Modeling and analysis of contact stiffness and friction of joint surface based on fractal theory[D]. Shenyang:Northeastern University, 2015.
[12] 温淑花.结合面接触特性理论建模及仿真[M].北京:国防工业出版社, 2012. WEN Shuhua. Theoretical modeling and simulation of interface contact characteristics[M]. Beijing:National Defense Industry Press, 2012.
[13] 郭丹枫,胡小秋,顾思闽,等.基于面积的结合面切向动刚度特性研究[J].设计与研究, 2011(4):51-54. GUO Danfeng, HU Xiaoqiu, GU Simin, et al. Study on the tangential dynamic stiffness of fixed joints based on areas[J]. Design and Research, 2011(4):51-54.
[14] MORAG Y, ETSION I. Resolving the contradiction of asperities plastic to elastic mode transition in current contact models of fractal rough surfaces[J]. Wear, 2007, 262(6):624-629.
[15] MANNERS W, GREENWOOD J A. Some observations on Persson's diffusion theory of elastic contact[J]. Wear, 2006, 261(6):600-610.
[16] PERSSON B N J, TOSATTI E. The effect of surface roughness on the adhesion of elastic solids[J]. The Journal of Chemical Physics, 2001, 115(12):597-5597.
[17] GREENWOOD J A, WILLIAMSON J B P P. Contact of nominally flat surfaces[J]. Proceedings of The Royal Society A Mathematical Physical and Engineering Sciences, 1966, 295.1442:300-319.
[18] JOHNSON K L. Contact mechanics[M]. Cambridge:Cambridge University, 1985.
[19] POPOV V L. Contact mechanics and friction[M]. Berlin Heidelberg:Springer, 2010.
[20] LUO Z J, SONG B J, HAN J Y, YAN S Z. Evolution of real contact area during stick-slip movement observed by total reflection method[J]. Chinese Physics B, 2019, 28(10):405-411.
[21] YAMADA A, KAKUBARI T, EBATA H, et al. Dynamic characteristics of structures with joint[J]. Trans. Jpn. Soc. Mech. Eng, 1983, 49(438):182-190.
[22] MCCOOL J I. Comparison of models for the contact of rough surfaces[J]. Wear, 1986, 107(1):37-60.
[23] NAYAK P R. Random process model of rough surfaces[J]. Wear, 1971, 26(3):398-399.
[24] RAFAEL C G, RICHARD E W.数字图像处理[M].北京:电子工业出版社, 2016. RAFAEL C G, RICHARD E W. Digital image processing[M]. Beijing:Publishing House of Electronics Industry, 2016.
[25] THOMAS T R. Applications:Contact mechanics[M]. London:Imperial College Press, 1998.
[26] KOGUT L, ETSION I. Elastic-plastic contact analysis of a sphere and a rigid flat[J]. Journal of Applied Mechanics, 2002, 69(5):657-662.
[27] ZHAO Y W, CHANG L. A model of asperity interactions in elastic-plastic contact of rough surfaces[J]. Journal of Tribology, 2001, 123(4):857-864.

考虑尺度的结合面切向刚度模型

Model of Tangential Stiffness of Joint Surface Considering Scale

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	何远鹏, 韩健, 陈鹏, 董博南, 肖新标, 圣小珍. 嵌入式轨道与扣件轨道曲线啸叫噪声试验分析[J]. 机械工程学报, 2023, 59(6): 194-203.
[2]	杨云帆, 凌亮, 张涛, 王开云, 翟婉明. 牵引/制动载荷和复杂黏着条件对地铁轮轨动态相互作用影响研究[J]. 机械工程学报, 2023, 59(12): 284-296.
[3]	王宇, 张帆, 晁世麟, 訾艳阳. 硬盘头盘界面的微观接触模型及动力学响应分析[J]. 机械工程学报, 2022, 58(3): 121-130.
[4]	安琪, 索双富, 林福严, 白玉柱, 耿海旭, 时剑文. 平面磨削粗糙表面的微观接触模型[J]. 机械工程学报, 2020, 56(7): 240-248.
[5]	运睿德, 丁北. 考虑多尺度接触状态的新接触模型[J]. 机械工程学报, 2019, 55(9): 80-89.
[6]	牛留斌, 刘金朝. 基于高频轮轨接触模型的轨道短波不平顺敏感波长特性分析[J]. 机械工程学报, 2019, 55(8): 173-182.
[7]	陈永会, 张学良, 温淑花, 兰国生. 考虑弹塑性阶段的结合面法向接触阻尼分形模型[J]. 机械工程学报, 2019, 55(16): 58-68.
[8]	石坤, 张广鹏, 魏锋涛, 原园. 机械结合部动态特性的等效参数研究[J]. 机械工程学报, 2018, 54(19): 144-149.
[9]	李和言, 王宇森, 熊涔博, 陈飞, 李明阳, 杨硕. 离合器配对摩擦副径向温度梯度对接触比压的影响[J]. 机械工程学报, 2018, 54(1): 136-143.
[10]	吴涛, 吴兵, 温泽峰, 金学松. 基于不同微观固体接触模型的轮轨表面变形特性分析[J]. 机械工程学报, 2017, 53(22): 134-142.
[11]	李玲, 蔡安江, 蔡力钢, 阮晓光. 螺栓结合面微观接触模型[J]. 机械工程学报, 2016, 52(7): 205-210.
[12]	胡兆稳, 刘焜, 刘小君, 王伟. 静态接触中表面纹理对塑性变形界面微凸体平坦化的影响[J]. 机械工程学报, 2016, 52(3): 93-100.
[13]	马登秋, 侯力, 魏永峭, 陈建. 基于分形理论的圆弧齿轮滑动摩擦接触力学模型^*[J]. 机械工程学报, 2016, 52(15): 121-127.
[14]	周俊峰, 王伟, 张晨, 刘焜. 动态摩擦因数对蝶式制动器温度场影响的试验和模拟研究[J]. 机械工程学报, 2016, 52(10): 150-157.
[15]	王庚祥,刘宏昭. 考虑球面副间隙的4-SPS/CU并联机构动力学分析[J]. 机械工程学报, 2015, 51(1): 43-51.