双螺杆水蒸气压缩机喷水冷却特性研究

doi:10.3901/JME.2023.06.141

机械工程学报 ›› 2023, Vol. 59 ›› Issue (6): 141-148.doi: 10.3901/JME.2023.06.141

• 可再生能源与工程热物理 • 上一篇下一篇

扫码分享

双螺杆水蒸气压缩机喷水冷却特性研究

田雅芬^1,2, 耿妍婷¹, 夏阳¹, 赵兆瑞^1,2

1. 上海理工大学制冷与低温工程研究所上海 200093;
2. 上海理工大学上海市动力工程多相流动与传热重点实验室上海 200093

收稿日期:2022-06-05 修回日期:2022-10-30 出版日期:2023-03-20 发布日期:2023-06-03
通讯作者: 田雅芬(通信作者),女,1991出生,博士,讲师,硕士研究生导师。主要研究方向为螺杆水蒸气压缩机与膨胀机内部流动与传热传质机理。E-mail:yftian_usst@qq.com
基金资助:
国家自然科学基金 (52206016、51206022)、上海市青年科技英才扬帆计划(20YF1431700)、科技部冬奥专项(2020YFF0303901)和中央引导地方科技发展资金(YDZX20213100003002)资助项目。

Investigation on the Characteristics of Water Injected Twin-screw Steam Compressor

TIAN Yafen^1,2, GENG Yanting¹, XIA Yang¹, ZHAO Zhaorui^1,2

1. Institute of Refrigeration and Cryogenics, University of Shanghai for Science and Technology, Shanghai 200093;
2. Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering, Shanghai 200093

Received:2022-06-05 Revised:2022-10-30 Online:2023-03-20 Published:2023-06-03

摘要/Abstract

摘要： 水蒸气压缩机在机械蒸汽压缩、海水淡化、高温热泵等工业领域具有良好的节能潜力与应用前景。喷水可以有效解决排气温度过高的问题，提高水蒸气压缩机的性能。为了获得最佳喷水量的变化规律，建立了双螺杆水蒸气压缩机喷水冷却实际工作过程的传热传质模型，考虑喷入水的汽化、泄漏、闪蒸、输送等对实际压缩过程的影响。与试验结果对比，计算结果误差在±5%以内，表明模型能够较好地预测喷水螺杆水蒸气压缩机的工作过程与性能。利用此模型，研究了喷水量、转速和吸气压力对压缩机性能的影响。研究结果表明，喷水可以有效提升压缩机性能，相比不喷水而言，喷水在部分工况下可将压缩机容积效率提高11.9%，绝热效率提高17.2%，且存在最佳喷水量，使得喷水螺杆水蒸气压缩机的性能最佳，最佳喷水量随着转速、吸气压力的增加而增加；最佳喷水比主要受转速的影响，随着转速的增大而增大，其最佳喷水比在8.9%～10.4%之间；随着吸气压力降低，压差增大，喷水螺杆水蒸气压缩机的性能降低较快，表明泄漏对喷水螺杆水蒸气压缩机性能影响较大，尚需进一步研究。

关键词: 螺杆压缩机, 水蒸气, 喷水冷却, 传热传质

Abstract: Steam compressor shows great energy-saving potential in mechanical vapor compression, desalination and high temperature heat pump in all industries. With water injection, high exhaust temperature can be avoided and the compressor performance will be enhanced. A thermodynamic model was developed for the real working process in water injected twin-screw compressor. Heat and mass transfer between the compressed vapor and injected water were considered altogether with leakage. The errors between simulated and experimental results were within ±5%, which proves the proposed model efficient for performance prediction. The effects of injected water flowrate and rotating speed on the compressor performance were investigated. Results indicate that water injection can efficiently improve the compressor performance. Compared with zero injection, the volumetric efficiency and isentropic efficiency can be improved by 11.9% and 17.2% respectively under certain conditions. Moreover, there exists an optimal flowrate of injected water which increases linearly with rotating speed. The optimal mass ratio of injected water also slightly increases with rotating speed, which remains about 8.9%~10.4% for the investigated compressor. With the increase of suction pressure, the compressor efficiency drops quickly due to larger leakage, which needs further illustration.

Key words: twin-screw compressor, steam, water injection cooling, heat and mass transfer

中图分类号:

TB652

田雅芬, 耿妍婷, 夏阳, 赵兆瑞. 双螺杆水蒸气压缩机喷水冷却特性研究[J]. 机械工程学报, 2023, 59(6): 141-148.

TIAN Yafen, GENG Yanting, XIA Yang, ZHAO Zhaorui. Investigation on the Characteristics of Water Injected Twin-screw Steam Compressor[J]. Journal of Mechanical Engineering, 2023, 59(6): 141-148.

参考文献

[1] CHAMOUN M,RULLIERE R,HABERSCHILL P,et al. Experimental and numerical investigations of a new high temperature heat pump for industrial heat recovery using water as refrigerant[J]. International Journal of Refrigeration,2014,44:177-188.
[2] HU B,WU D,WANG R. Water vapor compression and its various applications[J]. Renewable & Sustainable Energy Reviews,2018,98:92-107.
[3] LIANG L,HAN D,MA R,et al. Treatment of high-concentration wastewater using double-effect mechanical vapor recompression[J]. Desalination,2013,314:139-146.
[4] 高磊,张凯,董冰,等. 螺杆水蒸气压缩机的MVR系统在碱回收中的应用[J]. 化工进展,2014,33(11):3112-3117. GAO Lei,ZHANG Kai,DONG Bing,et al. Research of MVR system with twin-screw vapor compressor in lye recovery[J]. Chemical Industry and Engineering Progress,2014,33(11):3112-3117.
[5] 张化福,张青春,童莉葛,等. 罗茨水蒸气压缩机性能试验研究[J]. 制冷学报,2022,43(1):68-73. ZHANG Huafu,ZHANG Qingchun,TONG Lige,et al. Experimental study on performance of roots steam compressor[J]. Journal of Refrigeration,2022,43(1):68-73.
[6] LI Q,POECHNA J,MULLER N. Design of a novel axial impeller as a part of counter-rotating axial compressor to compress water vapor as refrigerant[J]. Applied Energy,2011,88(9):3156-3168.
[7] 俞丽华,许树学,马国远. 中间补气对罗茨式水蒸气制冷压缩机工作性能的影响[J]. 制冷与空调,2016,30(4):502-507. YU Lihua,XU Shuxue,MA Guoyuan. Effect of a vapor injection on working performances of the roots compressor in water vapor compression refrigeration system[J]. Refrigeration and Air Conditioning,2016,30(4):502-507.
[8] YANG J,ZHANG C,ZHANG Z,et al. Study on mechanical vapor recompression system with wet compression single screw compressor[J]. Applied Thermal Engineering,2016,103:205-211.
[9] 王力威,庄景发,杨鲁伟,等. 单螺杆水蒸汽压缩机驱动的MVR系统性能试验研究[J]. 中国科学院大学学报. 2015,32(1):38-45. WANG Liwei,ZHUANG Jingfa,YANG Luwei,et al. Experimental study on performance of MVR system driven by single screw water vapor compressor[J]. Journal of University of Chinese Academy of Sciences,2015,32(1):38-45.
[10] SHEN J,FENG G,XING Z,et al. Theoretical study of two-stage water vapor compression systems[J]. Applied Thermal Engineering,2019,147:972-982.
[11] SHEN J,XING Z,WANG X,et al. Analysis of a single-effect mechanical vapor compression desalination system using water injected twin screw compressors[J]. Desalination,2014,333(1):146-153.
[12] SHEN J,XING Z,ZHANG K,et al. Development of a water-injected twin-screw compressor for mechanical vapor compression desalination systems[J]. Applied Thermal Engineering,2016,95:125-135.
[13] TIAN Y,SHEN J,WANG C,et al. Modeling and performance study of a water-injected twin-screw water vapor compressor[J]. International Journal of Refrigeration,2017,83:75-87.
[14] 郭霆,沈九兵,田雅芬,等. 螺杆蒸汽压缩机工作过程喷水冷却特性研究[J]. 机械工程学报. 2016,52(24):147-154. GUO Ting,SHEN Jiubing,TIAN Yafen,et al. Investigation on the influence of water injection on twin screw water vapor compressors' working process[J]. Journal of Mechanical Engineering,2016,52(24):147-154.
[15] 张良. 湿蒸汽两相压缩过程工作特性研究[D]. 大连:大连理工大学,2006. ZHANG Liang. Research on the characteristics of wet steam compression process[D]. Dalian:Dalian University of Technology,2006.
[16] 王闯,张益钦,袁恒川,等. 水润滑双螺杆空压机工作过程传热传质特性研究[J]. 机械工程学报,2021,57(8):247-254. WANG Chuang,ZHANG Yiqin,YUAN Hengchuan,et al. Research on heat and mass transfer characteristics of water lubricated twin-screw air compressor[J]. Journal of Mechanical Engineering,2021,57(8):247-254.
[17] 肖芳,刘常峰,姚同林. 螺杆式蒸汽压缩热泵系统性能试验研究[J]. 制冷技术,2017,37(5):48-52. XIAO Fang,LIU Changfeng,YAO Tonglin. Experimental study on performance of screw type steam compression heat pump system[J]. Chinese Journal of Refrigeration Technology,2017,37(5):48-52.

双螺杆水蒸气压缩机喷水冷却特性研究

Investigation on the Characteristics of Water Injected Twin-screw Steam Compressor

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张云舒, 吴斌涛, 赵昀, 丁东红, 潘增喜, 李会军. 电弧熔丝增材制造传热传质数值模拟研究现状与展望[J]. 机械工程学报, 2024, 60(8): 65-80.
[2]	王闯, 张益钦, 袁恒川, 邢子文. 水润滑双螺杆空压机工作过程传热传质特性研究[J]. 机械工程学报, 2021, 57(8): 247-254.
[3]	周祥曼, 田启华, 杜义贤, 柏兴旺, 张海鸥. 外加横向磁场作用电弧增材成形过程中的传热传质仿真[J]. 机械工程学报, 2018, 54(12): 193-206.
[4]	王海斗, 陈书赢, 马国政, 邢志国, 何鹏飞, 徐滨士. 等离子射流与喷涂粒子微观交互作用研究现状[J]. 机械工程学报, 2017, 53(24): 1-11.
[5]	沈九兵, 王瑞鑫, 周明龙, 陈文卿. 半封闭螺杆制冷压缩机排气噪声模拟与试验研究[J]. 机械工程学报, 2017, 53(20): 169-175.
[6]	郭霆, 沈九兵, 田雅芬, 邢子文. 螺杆蒸汽压缩机工作过程喷水冷却特性研究^*[J]. 机械工程学报, 2016, 52(24): 147-154.
[7]	沈九兵, 张凯, 邢子文, 房文娜, 曹建文. 采用双螺杆压缩机的机械蒸汽再压缩污水处理系统试验研究[J]. 机械工程学报, 2016, 52(10): 185-190.
[8]	吕方明;王坤;黄树红;吴波;高峰. 超临界水蒸气氧化的12Cr钢发射率试验研究[J]. , 2012, 48(18): 124-129.
[9]	李锦上. 空间共轭啮合副二次包络面三面共点构造法[J]. , 2011, 47(21): 43-48.
[10]	熊伟;冯全科. 基于三维的双螺杆压缩机转子干涉研究[J]. , 2005, 41(6): 55-59.
[11]	段永涛;文怀兴;张德翱. 基于热平衡分析法的喷射器引射系数计算与分析[J]. , 2005, 41(3): 42-46.
[12]	张学军;代彦军;王如竹. 蜂窝式除湿转轮的传热传质数学模型及其试验验证[J]. , 2005, 41(1): 82-87.
[13]	张德翱;段永涛. 水蒸气喷射泵设计中有关引射系数计算的若干问题探讨[J]. , 2004, 40(7): 51-54.
[14]	蔡睿贤;张娜. 含湿毛细多孔介质传热与传质基本方程的一组代数显式解析解[J]. , 2003, 39(6): 1-3.
[15]	朱亮;张爱华. 水蒸气保护电弧焊焊缝的氢质量分数[J]. , 2002, 38(8): 143-146.