Research on the Cylinder Block/Valve Plate Interface Performance in Ultra-high-pressure and High-speed Swash Plate Type Variable Displacement Axial Piston Machines

doi:10.3901/JME.2025.02.358

Abstract

Abstract: Ultra-high working pressure is the inevitable development trend and requirement of hydraulic technology. However, the ultra-high working pressure increases the overturning moment of the cylinder block of the axial piston pump, aggravates the overturn of the cylinder block, and is more likely to cause eccentric wear failure and leakage in the cylinder block/valve plate interface. It puts forward the higher requirements for the friction, lubrication and sealing, load-carrying performance of the cylinder block/valve plate pair. Therefore, A numerical analytical model is established, which is coupled with the mapping relationship between the structure parameters, operating parameters, oil performance parameters, etc., and the friction, lubrication as well as sealing, load-carrying properties of the cylinder block/valve plate pair oil film. Based on this model, a cylinder block/valve plate pair with a plane auxiliary support structure adapted to the ultra-high pressure 63 MPa working condition is designed through numerical analysis. It is founded that the support structure can make the oil film of the cylinder block in contact with the valve plate due to inclination of cylinder block to generate additional bearing capacity, thus further balancing the load overturning moment on the cylinder block and enhancing the anti-overturning ability of the oil film of the cylinder block/valve plate pair. The cylinder block/valve plate pair is applied to the first domestically developed ultra-high-pressure high-speed swash plate type variable displacement axial piston conjoined pump motor physical prototype with a nominal pressure of 63MPa, and the good working performance of the cylinder block/valve plate pair is verified through experimental tests. The research results can provide advanced design methods and guidance for the research and development of the high-performance cylinder block/valve plate pair.

Key words: axial piston pump, axial piston motor, ultra-high pressure, auxiliary support, cylinder block/valve plate pair, oil film

CLC Number:

TH137

HU Min, QIU Tianxiang, WU Zhe, LIU Rui, ZENG Yishan, LIU Changhai. Research on the Cylinder Block/Valve Plate Interface Performance in Ultra-high-pressure and High-speed Swash Plate Type Variable Displacement Axial Piston Machines[J]. Journal of Mechanical Engineering, 2025, 61(2): 358-370.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.2025.02.358

http://www.cjmenet.com.cn/EN/Y2025/V61/I2/358

References

[1] IVANTYSYNOVA M，BAKER J. Power loss in the lubricating gap between cylinder block and valve plate of swash plate type axial piston machines[J]. International Journal of Fluid Power，2009，10(2)：29-43.
[2] SHANG L，IVANTYSYNOVA M. Scaling criteria for axial piston machines based on thermo-elastohydrodynamic effects in the tribological interfaces[J]. Energies，2018，11(11)：3210.
[3] CHACON R，IVANTYSYNOVA M. An investigation of the impact of the elastic deformation of the end case/ housing on axial piston machines cylinder block/valve plate lubricating interface[C]// 10th International Fluid Power Conference，Dresden，2016：283-294.
[4] CHACON R，IVANTYSYNOVA M. Thermal effects on the fluid film in the cylinder block/valve plate interface due to compression and expansion of the fluid[J]. JFPS International Journal of Fluid Power System，2019，11(3)：136-142.
[5] CHACON R，IVANTYSYNOVA M. Virtual prototyping of axial piston machines：Numerical method and experimental validation[J]. Energies，2019，12(9)：1674.
[6] ERNST M H，IVANTYSYNOVA M. Cylinder bore micro-surface shaping for high pressure axial piston machine operation using water as hydraulic fluid[C]// Asme/bath Symposium on Fluid Power & Motion Control. 2017：V001T01A043.
[7] SHIN J H，KANG B S，KIM K W. Surface lay effects on the lubrication characteristics in the valve part of a swash-plate type axial piston pump[J]. Journal of the Korean Society of Tribologists and Lubrication Engineers，2012，28(1)：12-18.
[8] SHIN J H，KIM K W. Effect of surface non-flatness on the lubrication characteristics in the valve part of a swash-plate type axial piston pump[J]. Meccanica，2014，49(5)：1275-1295.
[9] SHIN J H，CHO K W. A simplified calculation model for the sliding contact boundaries in a hydrostatic piston mechanism[J]. Journal of Engineering Mathematics，2018，113(1)：143-163.
[10] TOMANIK E. Modelling the hydrodynamic support of cylinder bore and piston rings with laser textured surface[J]. Tribology International，2013，59：90-96.
[11] RICHARDSON D，SADEGHI F，RATEICK R G，et al. Experimental and analytical investigation of floating valve plate motion in an axial piston pump[J]. Tribology Transactions，2017，60(3)：537-547.
[12] RICHARDSON D，SADEGHI F，RATEICK R G，et al. Dynamic modeling of floating valve plate motion in an axial piston pump[J]. Tribology Transactions，2018，61(4)：683-693.
[13] RICHARDSON D，SADEGHI F，RATEICK R G，et al. Surface modification effects on lubricant temperature and floating valve plate motion in an axial piston pump[J]. Journal of Engineering Tribology，2019，234(1)：135065011984118.
[14] 侯亮，赖伟群，崔凯，等. 轴向柱塞马达平面配流副油膜润滑特性建模及分析[J]. 华南理工大学学报(自然科学版)，2021，49(2)：99-109. HOU Liang，LAI Weiqun，CUI Kai，et al. Modeling and analysis of oil film lubrication characteristics of axial piston motor plane valve pair[J]. Journal of South China University of Technology (Natural Science Edition)，2021，49(2)：99-109.
[15] CHEN Yuan，ZHANG Junhui，XU Bing，et al. Multi-objective optimization of micron-scale surface textures for the cylinder/valve plate interface in axial piston pumps[J]. Tribology International，2019，138：316-329.
[16] 马浩，高殿荣，毋少峰，等. 水压马达仿生非光滑表面配流副摩擦磨损研究[J]. 机械工程学报，2018，54(13)：142-152. MA Hao，GAO Dianrong，WU Shaofeng，et al. Experimental study on friction-wear for valve plate with bionic non-smooth surface of hydraulic motor[J]. Journal of Mechanical Engineering，2018，54(13)：142-152.
[17] 邓海顺，祁胜，于海武，等. 轴向柱塞泵配流副低压区织构化数值分析[J]. 农业机械学报，2011，42(6)：203-207. DENG Haishun，QI Sheng，YU Haiwu，et al. Numerical analysis for textured port plate of axial piston pump[J]. Transactions of the Chinese Society of Agricultural Machinery，2011，42(6)：203-207．
[18] 许路. 高压高速轴向柱塞泵配流副润滑特性研究[D]. 北京：北京理工大学，2016. XU Lu. Study on the lubrication characteristics of the valve plate bearing in hydraulic axial piston pump[D]. Beijing：Beijing Institute of Technology，2016.
[19] 赵愿，周俊杰，荆崇波，等. 轴向柱塞泵端面开槽配流副动压支撑特性[J]. 哈尔滨工业大学学报，2018，50(1)：169-174. ZHAO Yuan，ZHOU Junjie，JING Chongbo，et al. Effect of grooved face on the dynamic pressure support characteristics of cylinder/valve plate pair in the axial piston pump[J]. Journal of Harbin Institute of Technology，2018，50(1)：169-174.
[20] 胡敏. 轴向柱塞泵摩擦副功率损失分析与表面形貌设计研究[D]. 杭州：浙江大学，2017. HU Min. Study on power losses and design technology for the surface topography of friction pairs of axial piston pump[D]. Hangzhou：Zhejiang University，2017.
[21] 王彬，周华，杨华勇. 轴向柱塞泵配流副油膜试验原理及控制特性[J]. 机械工程学报，2009，45(11)：113-118. WANG Bin，ZHOU Hua，YANG Huayong. Principle of oil film test on port pair of axial piston pump and control characteristics[J]. Journal of Mechanical Engineering 2009，45(11)：113-118.
[22] WANG Lei DENG Haishun，GUO Yongchun，et al. Lubrication characteristics of external return spherical hinge pair of axial piston pump or motor under combined action of inclination and offset distance[J]. Journal of Central South University，2021，28(8)：2375-2393.
[23] 王建磊，门川皓，赵伟刚，等. 动静压机械密封的结构设计及端面槽型优化研究[J]. 机械工程学报，2021，57(9)：108-117. WANG Jianlei，MEN Chuanhao，ZHAO Weigang，et al. Research on structural design and end face slot of optimization of hydrodynamic and hydrostatic mechanical seal[J]. Journal of Mechanical Engineering，2021，57(9)：108-117.
[24] ZHAO Jiang’ao， FU Yongling，MA Jiming，et al. Review of cylinder block/valve plate interface in axial piston pumps：Theoretical models，experimental investigations，and optimal design[J]. Chinese Journal of Aeronautics，2021，34(1)：111-134.
[25] 张斌. 轴向柱塞泵的虚拟样机及油膜压力特性研究[D]. 杭州：浙江大学，2009. ZHANG Bin. Study on virtual prototype and pressure characteristics of oil film for axial piston pump[D]. Hangzhou：Zhejiang University，2009.
[26] 孙亚楠，高殿荣. 双介质双排量轴向柱塞泵配流窗处液体的泄漏和掺混特性[J]. 机械工程学报，2020，56(22)：271-280. SUN Yanan，GAO Dianrong. Liquid leakage and mixing characteristics at distribution windows of dual-medium and dual-displacement axial piston pumps[J]. Journal of Mechanical Engineering，2020，56(22)：271-280.
[27] 闫伟鹏. 轴向柱塞泵配流副抗倾覆稳定性及油膜润滑特性研究[D]. 哈尔滨：哈尔滨工业大学，2020. YAN Weipeng. Research on stability against tipping and lubrication characteristics of cylinder block/valve plate in axial piston pumps[D]. Harbin：Harbin Institute of Technology，2020.