Research Development on Wrinkling Prediction and Suppression for Sheet Hydroforming of Thin-walled Deep Drawing Parts

doi:10.3901/JME.2016.04.020

Abstract

Abstract: Deep drawn parts, which have been focused on by researchers for many decades, are widely used in the aerospace, automobile and ship industries. While with the new requirements of light weight, high accuracy, low cost and low energy, the ratio between thickness and diameter of some key components such as propellant storage tank of a launch vehicle is even lower than 0.3%, thus wrinkling cannot be neglected. This defect decreases the parts quality, reduces the molds life and affects the stability of industry production. The prediction method of the wrinkling, as well as the numerical simulation and experiments about this tricky problem are introduced. Furthermore, to solve the inner wrinkling, the sheet hydroforming technology development on the wrinkling control is shown. It can be concluded that appropriate sheet hydroforming process design can be used to control the wrinkling. The current problem in this area and the future study tendency are depicted.

Key words: energy method, sheet hydroforming, thin-walled deep drawing parts, wrinkling

CLC Number:

TG394

CHEN Yizhe, LIU Wei, YUAN Shijian. Research Development on Wrinkling Prediction and Suppression for Sheet Hydroforming of Thin-walled Deep Drawing Parts[J]. Journal of Mechanical Engineering, 2016, 52(4): 20-28.

References

[1] NGAILE G,KINSEY B. Advances in plastic forming of metals[J]. Journal of Manufacturing Science and Engineering,2011,133(6)：060301-1-060301-3.
[2] LEE M G,KIM C,PAVLINA E J,et al. Advances in sheet forming-materials modeling,numerical simulation,and press technologies[J]. Journal of Manufacturing Science and Engineering,2011,133(6)：061001-1-061001-12.
[3] KADKHODAYAN M,MOAYYEDIAN F. Analytical elastic-plastic study on flange wrinkling in deep drawing process[J]. Scientia Iranica,2011,18(2)：250-260.
[4] WANG X F,YANG Q S,LAW S. Wrinkled membrane element based on the wrinkling potential[J]. International Journal of Solids and Structures,2014,51(21)：3532-3548.
[5] 龚峰,张顺,吴挺岛. 1060纯铝微杯形件微拉深成形研究[J]. 机械工程学报,2014,50(24)：44-49.
GONG Feng,ZHANG Shun,WU Tingdao. Research on micro deep drawing of pure aluminum 1060 micro cylindrical cups[J]. Journal of Mechanical Engineering,2014,50(24)：44-49.
[6] 龚学鹏,李明哲,胡志清. 连续多点成形过程中起皱缺陷的有限元分析[J]. 机械工程学报,2010,46(22)：31-35.
GONG Xuepeng,LI Mingzhe,HU Zhiqing. Finite element analysis on wrinkle during process of continuous multi-point forming[J]. Journal of Mechanical Engineering,2010,46(22)：31-35.
[7] KASAEI M M,NAEINI H M,ABBASZADEH B,et al. Flange wrinkling in flexible roll forming process[J]. Procedia Engineering,2014,81：245-250.
[8] 李春峰. 金属塑性成形工艺及模具设计[M]. 北京：高等教育出版社,2008.
LI Chunfeng. Metal plastic deformation process and design of molds[M]. Beijing：Higher Education Press,2008.
[9] 苑世剑. 现代液压成形技术[M]. 北京：国防工业出版社,2009.
YUAN Shijian. Modern hydroforming technology[M]. Beijing：National Defence Industry Press,2009.
[10] 余同希,章亮炽. 塑性弯曲理论及其应用[M]. 北京：科学出版社,1992.
YU Tongxi,ZHANG Liangzhi. Theory and application of plastic bending process[M]. Beijing：Science Press,1992.
[11] GECKELER J W. Plastisches Knicken der Wandung von Hohlzylindern und einige andere Faltungserscheinungen an Schalen und Blechen[J]. ZAMM-Journal of Applied Mathematics and Mechanics/Zeitschrift für Angewandte Mathematik und Mechanik,1928,8(5)：341-352.
GECKELER J W. Plastic buckling of the flange area of cylindrical parts and some other bowls and plates[J]. Journal of Applied Mathematics and Mechanics,1928,8(5)：341-352.
[12] YU T X,JOHNSON W. The buckling of annular plates in relation to the deep-drawing process[J]. International Journal of Mechanical Sciences,1982,24(3)：175-188.
[13] WANG X,CAO J. On the prediction of side-wall wrinkling in sheet metal forming processes[J]. International Journal of Mechanical Sciences,2000,42(12)：2369-2394.
[14] KAWKA M,OLEJNIK L,ROSOCHOWSKI A,et al. Simulation of wrinkling in sheet metal forming[J]. Journal of Materials Processing Technology,2001,109(3)：283-289.
[15] ZHANG S H,LANG L H,KANG D C,et al. Hydromechanical deep-drawing of aluminum parabolic workpieces-experiments and numerical simulation[J]. International Journal of Machine Tools and Manufacture,2000,40(10)：1479-1492.
[16] MENG B,WAN M,WU X,et al. Inner wrinkling control in hydrodynamic deep drawing of an irregular surface part using drawbeads[J]. Chinese Journal of Aeronautics,2014,27(3)：697-707.
[17] 许沂,周丽新,张士宏,等. 采用可移动凹模的板材液压成形技术[J]. 机械工程学报,2004,40(8)：106-109.
XU Yi,ZHOU Lixin,ZHANG Shihong,et al. Hydroforming of sheet metal with a movable die component[J]. Chinese Journal of Mechanical Engineering,2004,40(8)：106-109.
[18] LIU W,XU Y,YUAN S. Effect of pre-bulging on wrinkling of curved surface part by hydromechanical deep drawing[J]. Procedia Engineering,2014,81：914-920.
[19] SENIOR B W. Flange wrinkling in deep-drawing operations[J]. Journal of the Mechanics and Physics of Solids,1956,4：235-246.
[20] TIMOSHENKO S P,GERE J M. Theory of elastic stability[M]. New York：McGraw-Hill,1961.
[21] KAFTANOGLU B. Plastic analysis of flange wrinkling in axisymmetrical deep drawing[C]//21st International Machine Tool Design and Restoration Conference,1980,1：21-28.
[22] CAO J,BOYCE M C. Wrinkling behavior of rectangular plates under lateral constraint[J]. International Journal of Solids and Structures,1997,34(2)：153-176.
[23] CAO J. Prediction of plastic wrinkling using the energy method[J]. Journal of Applied Mechanics,1999,66(3)：646-652.
[24] WANG X,CAO J. An analytical prediction of flange wrinkling in sheet metal forming[J]. Journal of Manufacturing Processes,2000,2(2)：100-107.
[25] AGRAWAL A,REDDY N V,DIXIT P M. Determination of optimum process parameters for wrinkle free products in deep drawing process[J]. Journal of Materials Processing Technology,2007,191(1)：51-54.
[26] SHAFAAT M A,ABBASI M,KETABCHI M. Investigation into wall wrinkling in deep drawing process of conical cups[J]. Journal of Materials Processing Technology,2011,211(11)：1783-1795.
[27] HILL R. A general theory of uniqueness and stability in elastic-plastic solids[J]. Journal of the Mechanics and Physics of Solids,1958,6(3)：236-249.
[28] HUTCHINSON J W. Plastic buckling[J]. Advances in Applied Mechanics,1974,14：67-144.
[29] HUTCHINSON J W,NEALE K W. Wrinkling of curved thin sheet metal[J]. Plastic Instability,1985：71-78.
[30] TUĞCU P. Plate buckling in the plastic range[J]. International Journal of Mechanical Sciences,1991,33(1)：1-11.
[31] WANG C T,KINZEL G,ALTAN T. Wrinkling criterion for an anisotropic shell with compound curvatures in sheet forming[J]. International Journal of Mechanical Sciences,1994,36(10)：945-960.
[32] ZHANG L C,YU T X,WANG R. Investigation of sheet metal forming by bending-part Ⅱ. plastic wrinkling of circular sheets pressed by cylindrical punches[J]. International Journal of Mechanical Sciences,1989,31(4)：301-308.
[33] YOSHIDA K,HAYASHI J,NIYAUCHI K,et al. Assessment of fitting behavior and shape fixation by yoshida buckling test-a way to overall formability[C]//
International Symposium on New Aspects of Sheet Metal Forming ISIJ,Tokyo,Japan. 1981：125-150.
[34] 周贤宾,周敏. 方板对角拉伸试验与板材的综合成形性[J]. 锻压技术,1985(4)：52-57.
ZHOU Xianbin,ZHOU Min. Diagonal tension test and the formability of sheet[J]. Forging & Stamping Technology,1985(4)：52-57.
[35] NARAYANASAMY R,LOGANATHAN C. Study on wrinkling limit of interstitial free steel sheets of different thickness when drawn through conical and tractrix dies[J]. Materials & Design,2008,29(7)：1401-1411.
[36] KIM J B,YOON J W,YANG D Y,et al. Investigation into wrinkling behavior in the elliptical cup deep drawing process by finite element analysis using bifurcation theory[J]. Journal of Materials Processing Technology,2001,111(1)：170-174.
[37] 李春峰,李硕本. 半球形零件冲压变形失稳点分析[J]. 塑性工程学报,1995,2(1)：36-42.
LI Chunfeng,LI Shuoben. Analysis of instability points of hemispherical parts in sheet metal forming[J]. Journal of Plasticity Engineering,1995,2(1)：36-42.
[38] 康达昌,郎利辉. 充液拉深工艺的研究[J]. 哈尔滨工业大学学报,2000,32(5)：42-44.
KANG Dachang,LANG Lihui. Hydrodynamic deep drawing process[J]. Journal of Harbin Institute of Technology,2000,32(5)：42-44.
[39] XU Y,LI F,LIU X,et al. Effects of pre-bulging on 2024 aluminum alloy complex-shaped components[J]. JOM,2011,63(5)：39-41.
[40] 万敏,杨玉英. 圆锥形零件的冲压成形极限[J]. 哈尔滨工业大学学报,1995,27(4)：121-125.
WAN Min,YANG Yuying. Forming limit of conical cup drawing[J]. Journal of Harbin Institute of Technology,1995,27(4)：121-125.
[41] LANG L,DANCKERT J,NIELSEN K B. Study on hydromechanical deep drawing with uniform pressure onto the blank[J]. International Journal of Machine Tools and Manufacture,2004,44(5)：495-502.
[42] ZHANG S H,DANCKERT J. Development of hydro-mechanical deep drawing[J]. Journal of Materials Processing Technology,1998,83(1)：14-25.
[43] 王仲仁,苑世剑,汤泽军,等. 省力液压成形的原理与途径[J]. 机械工程学报,2013,49(18)：99-105.
WANG Zhongren,YUAN Shijian,TANG Zejun,et al. Theory and Method of less-loading hydroforming[J]. Journal of Mechanical Engineering,2013,49(18)：99-105.
[44] 汤泽军,何祝斌,苑世剑. 内高压成形过程塑性失稳起皱分析[J]. 机械工程学报,2008,44(5)：34-38.
TANG Zejun,HE Zhubin,YUAN Shijian. Analysis of plastic wrinkling behavior in tube hydroforming process[J]. Chinese Journal of Mechanical Engineering,2008,44(5)：34-38.
[45] 徐永超,陈宇,苑世剑. 半球底筒形件充液拉深加载路径优化研究[J]. 哈尔滨工业大学学报,2008,40(7)：1076-1080.
XU Yongchao,CHEN Yu,YUAN Shijian. Loading path optimization of hydro-mechanical deep drawing of the cup with a semi-ball bottom[J]. Journal of Harbin Institute of Technology,2008,40(7)：1076-1080.
[46] YOSSIFON S,TIROSH J,KOCHAVI E. On suppression of plastic buckling in hydroforming processes[J]. International Journal of Mechanical Sciences,1984,26(6)：389-402.
[47] YOSSIFON S,TIROSH J. Buckling prevention by lateral fluid pressure in deep-drawing[J]. International Journal of Mechanical Sciences,1985,27(3)：177-185.
[48] YOSSIFON S,TIROSH J. On the permissible fluid-pressure path in hydroforming deep drawing processes-analysis of failures and experiments[J]. Journal of Manufacturing Science and Engineering,1988,110(2)：146-152.
[49] LO S,HSU T C,WILSON W R D. An analysis of the hemispherical-punch hydroforming processes[J]. Journal of Materials Processing Technology,1993,37(1)：225-239.
[50] ABEDRABBO N,ZAMPALONI M A,POURBOGHRAT F. Wrinkling control in aluminum sheet hydroforming[J]. International Journal of Mechanical Sciences,2005,47(3)：333-358.
[51] OH S I,JEON B H,KIM H Y,et al. Applications of hydroforming processes to automobile parts[J]. Journal of Materials Processing Technology,2006,174(1)：42-55.
[52] ZHANG S H,JENSEN M R,NIELSEN K B,et al. Effect of anisotropy and prebulging on hydromechanical deep drawing of mild steel cups[J]. Journal of Materials Processing Technology,2003,142(2)：544-550.
[53] 苑世剑,刘伟,徐永超. 板材液压成形技术与装备新进展[J]. 机械工程学报,2015,51(8)：20-28.
YUAN Shijian,LIU Wei,XU Yongchao. New development on technology and equipment of sheet hydroforming[J]. Journal of Mechanical Engineering,2015,51(8)：20-28.
[54] YUAN S J,LIU G,HUANG X R,et al. Hydroforming of typical hollow components[J]. Journal of Materials Processing Technology,2004,151(1)：203-207.
[55] YUAN S J,CUI X L,WANG X S. Investigation into wrinkling behavior of thin-walled 5A02 aluminum alloy tubes under internal and external pressure[J]. International Journal of Mechanical Sciences,2015,92：245-258.