基于模态预测及敏度分析的机床动特性设计方法

doi:10.3901/JME.2019.07.178

机械工程学报 ›› 2019, Vol. 55 ›› Issue (7): 178-186.doi: 10.3901/JME.2019.07.178

基于模态预测及敏度分析的机床动特性设计方法

李天箭¹, 吴晨帆¹, 沈磊¹, 孔祥志², 丁晓红¹

1. 上海理工大学机械工程学院上海 200093;
2. 沈阳机床(集团)计研究院有限公司沈阳 110142

收稿日期:2018-04-27 修回日期:2018-10-12 出版日期:2019-04-05 发布日期:2019-04-05
通讯作者: 李天箭(通信作者),女,1975年出生,博士,副教授,硕士研究生导师。主要研究方向为机床优化设计。E-mail:litianjian99@163.com
基金资助:
国家自然科学基金资助项目（51405300）。

Improving Machine Tool Dynamic Performance Using Modal Prediction and Sensitivity Analysis Method

LI Tianjian¹, WU Chenfan¹, SHEN Lei¹, KONG Xiangzhi², DING Xiaohong¹

1. School of Mechanical Engineering, University of Shanghai for Science and Technology, Shanghai 200093;
2. Shenyang Machine Tool(Group) Design and Research Institute Co., Ltd. Shenyang 110142

Received:2018-04-27 Revised:2018-10-12 Online:2019-04-05 Published:2019-04-05

摘要/Abstract

摘要： 为了提高机床的动态性能，以机床整机固有频率和频响函数振幅为目标，提出基于机床测试数据、进行试验模态分析及灵敏度计算的机床动态特性设计方法。方法首先提取机床测试数据建立机床结构原型模型，逐步计算机床大件结构和整机的固有频率对刚度、质量的灵敏度，确定结构薄弱环节；继而，对薄弱结构，采用模态预测和灵敏度分析方法设计计算，获取更合理的质量和刚度；之后，将设计分析结果输入LMS_Test.lab软件，借助软件完成对原型结构的模态修改，对修改后结构的动力学特性进行模态预测；最后，进行预测结果模态置信验证，确认模态预测的正确性，完整机床动态特性设计方法体系。将该方法应用于实际机床设计中，对比整机优化前后的频响函数曲线和仿真分析验证均证明，基于模态预测及灵敏度分析的机床动态特性设计方法完成的机床优化设计使得机床固有频率得到提高的同时振幅下降，机床的大件结构及整机的动态性能均有提升。

关键词: 动态特性, 机床, 结构动力修改, 灵敏度分析, 模态预测, 试验模态分析

Abstract: Based on machine test data, test mode analysis and sensitivity calculation, a design method is proposed to improve the dynamic performance of the machine tool, in which the natural frequencies of the machine tool and the amplitude of frequency response function are taken as the research objects. Firstly, the stiffness and mass sensitivity with respect to natural frequency are calculated to find weaknesses position of the structures, for the main components and the whole machine tool, respectively. Secondly, the more reasonable stiffness and mass are deduced based on the proposed method for the weaken structures. Thirdly, the improved scheme is modified by the LMS_Test.lab software and the reliability of the results is ensured by the modal analysis criterion (MAC). The method is applied to the machine tool design, and the simulation results show that the new machine tool dynamic performances are improved with the increased natural frequencies and the decreased amplitudes.

Key words: dynamic performance, experimental modal analysis, machine tool, modal prediction, sensitivity analysis, structural dynamic modification

中图分类号:

TG502
TH122

李天箭, 吴晨帆, 沈磊, 孔祥志, 丁晓红. 基于模态预测及敏度分析的机床动特性设计方法[J]. 机械工程学报, 2019, 55(7): 178-186.

LI Tianjian, WU Chenfan, SHEN Lei, KONG Xiangzhi, DING Xiaohong. Improving Machine Tool Dynamic Performance Using Modal Prediction and Sensitivity Analysis Method[J]. Journal of Mechanical Engineering, 2019, 55(7): 178-186.

参考文献

[1] 刘悦,汪劲松. 基于轴承及导轨接触刚度的混联机床静刚度研究及优化[J]. 机械工程学报, 2007, 43(9):151-155. LIU Yue, WANG Jinsong. Static stiffness research and optimization on a hybrid machine tool considering the stiffnesses of bearings and guideways[J]. Chinese Journal of Mechanical Engineering, 2007, 43(9):151-155.
[2] 李天箭,丁晓红,程凯. 基于空间统计学的机床动力学特性[J]. 机械工程学报, 2015, 51(21):87-94. LI Tianjian, DING Xiaohong, CHENG Kai. Machine tool dynamics based on spatial statistics[J]. Journal of Mechanical Engineering, 2015, 51(21):87-94.
[3] 王信锐. 数控机床能量模型及其应用研究[D]. 大连:大连理工大学, 2013. WANG Xinrui. Energy model of CNC machine tool and its application research[D]. Dalian:Dalian University of Technology, 2013.
[4] 郭垒,张辉,叶佩青,等. 基于灵敏度分析的机床轻量化设计[J]. 清华大学学报, 2011, 51(6):846-850. GUO Lei, ZHANG Hui, YE Peiqing, et al. Lightweight design of machine tools based on sensitivity analysis[J]. Journal of Tsinghua University, 2011, 51(6):846-850.
[5] DING Ye, ZHU Limin, ZHANG Xiaojian, et al. Response sensitivity analysis of the dynamic milling process based on the numerical integration method[J]. Chinese Journal of Mechanical Engineering, 2012, 25(5):940-946.
[6] ZHAO Liping, CHEN Hongren, YAO Yiyong, et al. A new approach to improving the machining precision based on dynamic sensitivity analysis[J]. International Journal of Machine Tools and Manufacture, 2016, 102:9-21.
[7] 廖伯瑜. 现代机械动力学及其工程应用[M]. 北京:机械工业出版社, 2003. LIAO Boyu. Modern mechanical dynamics and application[M]. Beijing:China Machine Press, 2003.
[8] LAW M, ALTINTAS Y, PHANI S. Rapid evaluation and optimization of machine tools with position-dependent stability[J]. International Journal of Machine Tools and Manufacture, 2013, 68:81-90.
[9] 邓聪颖,殷国富,方辉,等. 基于正交试验的机床结合部动刚度优化配置[J]. 机械工程学报, 2015, 51(19):146-153. DENG Congying, YIN Guofu, FANG Hui, et al. Optimal configuration of dynamic stiffness of machine tool joints based on orthogonal experiment[J]. Journal of Mechanical Engineering, 2015, 51(19):146-153.
[10] MAO Xinyong, LUO Bo, LI Bin, et al. An approach for measuring the FRF of machine tool structure without knowing any input force[J]. International Journal of Machine Tools and Manufacture, 2014, 86:62-67.
[11] 刘鲁宁. 高速面铣刀模态参数及其对切削性能影响研究[D]. 济南:山东大学, 2013. LIU Luning. Research on modal parameters and its influence on cutting performance of high speed milling cutter[D]. Jinan:Shandong University, 2013.
[12] ZAGHBANI I, SONGMENE V. Estimation of machine-tool dynamic parameters during machining operation through operational modal analysis[J]. International Journal of Machine Tools and Manufacture, 2009, 49(12-13):947-957.
[13] 张兴朝. 基于有限元分析的模块化数控机床结构动态设计研究[D]. 天津:天津大学, 2001. ZHANG Xingchao. Dynamic design of modular CNC machine tools based on finite element analysis[D]. Tianjin:Tianjin University, 2001.
[14] LI Bin, LUO Bo, MAO Xinyong, et al. A new approach to identifying the dynamic behavior of CNC machine tools with respect to different worktable feed speeds[J]. International Journal of Machine Tools and Manufacture, 2013, 72:73-84.
[15] 范利洪. 数控机床时变结构的动力学特性研究[D]. 武汉:华中科技大学, 2013. FAN Lihong. Study on the dynamics of CNC machine tools time-variant structure[D]. Wuhan:Huazhong University of Science and Technology, 2013.
[16] LI Tianjian, DING Xiaohong, CHENG Kai, et al. Dynamic optimization method with applications for machine tools based on approximation model[J]. Proceedings of the Institution of Mechanical Engineers, Part C:Journal of Mechanical Engineering Science,2017, 232(11):2009-2022.

基于模态预测及敏度分析的机床动特性设计方法

Improving Machine Tool Dynamic Performance Using Modal Prediction and Sensitivity Analysis Method

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王立平, 张兆坤, 邵珠峰, 王民. 机床制造加工数字化车间信息模型及其应用研究[J]. 机械工程学报, 2019, 55(9): 154-165.
[2]	杨闪闪, 王玲, 廖启豪, 梁斐然, 殷国富. 基于径向基函数法的五轴数控机床空间动态性能研究[J]. 机械工程学报, 2019, 55(9): 144-153.
[3]	王永青, 吴嘉锟, 刘阔, 刘海波, 刘志松, 廉盟. 数控机床精度保持性的定量评价与误差敏感度分析[J]. 机械工程学报, 2019, 55(5): 130-136.
[4]	陈旭, 朱才朝, 宋朝省, 谭建军, 朱永超. 紧急停机工况下风力发电机系统动态特性分析[J]. 机械工程学报, 2019, 55(5): 82-88.
[5]	董泽园, 李杰, 刘辛军, 梅斌, 陈俊宇. 数控机床两种几何误差建模方法有效性试验研究[J]. 机械工程学报, 2019, 55(5): 137-147.
[6]	李研彪, 郑航, 孙鹏, 徐涛涛, 王泽胜, 秦宋阳. 考虑关节摩擦的5-PSS/UPU并联机构动力学建模及耦合特性分析[J]. 机械工程学报, 2019, 55(3): 43-52.
[7]	刘巍, 李肖, 李辉, 潘翼, 贾振元. 基于双目视觉的数控机床动态轮廓误差三维测量方法[J]. 机械工程学报, 2019, 55(10): 1-9.
[8]	黄莹, 卢秉恒, 赵万华. 云计算在智能机床控制体系中的应用探析[J]. 机械工程学报, 2018, 54(8): 210-216.
[9]	许光辉, 王安斌, 宋月超, 王志强. 一种多层弹性部件轨道系统的动态特性试验研究[J]. 机械工程学报, 2018, 54(8): 74-82.
[10]	庹军波, 刘飞, 张华, 刘培基, 蔡维. 机床固有能量效率的内涵及其评价方法[J]. 机械工程学报, 2018, 54(7): 167-175.
[11]	唐清春, 尹韶辉, 王永强, 张健. 非模态回转轴旋转角的优化方法[J]. 机械工程学报, 2018, 54(3): 178-185.
[12]	廖永宜, 廖伯瑜. 基于模态柔度和能量分布的机床动态优化设计[J]. 机械工程学报, 2018, 54(23): 192-198.
[13]	金永平, 万步炎, 刘德顺, 彭佑多, 郭勇. 深海海底钻机收放系统动力学随机数值仿真方法研究[J]. 机械工程学报, 2018, 54(23): 112-120.
[14]	施虎, 何彬, 汪政, 梅雪松. 磁控形状记忆合金驱动特性及其在液压阀驱动器中的应用分析[J]. 机械工程学报, 2018, 54(20): 235-244.
[15]	邓超, 陶志奎, 吴军, 钱有胜, 夏爽. 基于性能退化的数控机床剩余寿命预测[J]. 机械工程学报, 2018, 54(17): 181-189.